MARLEY One Drop Wireless Charger User Guide

MARLEY One Drop Wireless Charger

DIAGRAM

1. USB-C connects to back of One Drop
2. USB-A end connects to USB AC adapter (not included)
3. B.USB-A end connects to USB port
4. rap cable strap around for storage (optional)

 CHARGING

• INPUT: 5V/3A, 9V/2A (QC 2.0, QC 3.0)
• OUTPUT: SW I 7.SW I lOW (MAX.)
• CHARGING DISTANCE: SUPPORTS CASES UP TO 3MM

STATUS

1. Charging
2. Charging Complete
3. Foreign Object Detected

LED INDICATION

1. Blinking
2. Off
3. Blinking

SET UP

•  Unwrap the included charging cable.
•  Connect the USB-C end of the cable into the charging port located on the back of One Drop.
•  Connect the USB-A end of the cable to the desired USS-powered port.
• Place One Drop on a flat and to stable surface ensure proper charging.

CHARGING

•  To charge your Qi-enabled wireless device, align the device centered on One Drop.
•  A white LED indicator light will slowly blink when your device is properly charging.
•  Once your device is fully charged, the white LED indicator light will turn off.
•  A red LED indicator light will blink if One Drop detects a foreign object or reaches excessive teMperature.
•  Quickly reMove the object or unplug One Drop to reduce the temperature before continuing usage.

STORAGE

•  When in storage or during travel, it is recOMMended to reMove the charging cable froM One Drop.
•  Carefully and neatly wind the charging cable.
•  Wrap the included cable ManageMent strap around the charging cable.
•  Insert the tab of the cable ManageMent strap into the loop.
•  Gently pull the tab ridges through the loop to secure.

REQUIREMENTS

•  Suitable only for Qi-coMpatible devices.
•  Not recOMMended for devices with over 3MM thick casing.
•  Please Note: To achieve Power Delivery fast charging, the device and power source Must also support Power Delivery.

COMPLIANCE INFO

ONE DROP

READ ALL INSTRUCTIONS BEFORE USE AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENC E.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer or an experienced radio/TV technician for help.
  This device complies with FCC radiation exposure limits set forth for an uncontrolled environment. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:  this device may not cause harmful interference, and  this device must accept any interference received, including interference that may cause undesired operation

WARNING:
For Australia and New Zealand for charging this equipment, only use Australian approved detachable power supply unit with the output ratings of 5V DC, 500 mA.

FCC & IC Radiation Exposure Statement:
This equipment complies with FCC and Canada radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter

CAUTION
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

ISEDC STATEMENT:
This device complies with Innovation, Science, and Economic Development Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:  this device may not cause interference, and this device must accept any interference, including interference that may cause undesired operation of the device. This Class B digital apparatus complies with Canadian ICES-003.

WE EXPLANATION
 This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled
waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. Hereby, FKA Brands Ltd, declares that this radio equipment is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. A copy of the Declaration of Conformity can be obtained from

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>