ideal lux Kool AP1 Wall Lamp Instruction Manual

ideal lux Kool AP1 Wall Lamp

Specifications

• Model: Kool AP1
• Max Wattage: 15W
• Socket Type: G9 LED
• Voltage: 240V
• Material: Cement

Product Usage Instructions

Assembly and Installation
Follow the assembly instructions in numerical order for proper installation. It is recommended to have the lighting fitting installed by a qualified electrician.

Safety Instructions
Ensure to adhere to the following safety guidelines:

1. The fixture complies with European safety standards EN 60.598-1.
2. For any installation or maintenance, always disconnect the power supply.
3. Use appropriate fixing accessories for different materials.
4. Do not look directly at the light source.

Maintenance

For maintenance and troubleshooting:

• If the lamp fails to light up, replace the fuse.
• Do not dismantle the LED light source.
• Refer to a qualified electrician for any damages to the external electrical cable.

INSTALLATION INSTRUCTION

• FOLLOW THE ASSEMBLY INSTRUCTIONS BY READING THE NUMERICAL PROGRESSION
• THE LIGHTING FITTING SHOULD BE INSTALLED BY A QUALIFIED ELECTRICIAN

PRE-CAUTION

SAFETY INSTRUCTIONS

1. This fitting is produced and tested in accordance with the strictest European safety standards (EN 60.598- 1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor or by a qualified electrician.
5.  Always isolate power before commencing installation, maintenance or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires not suitable for recessed on normally flammable surfaces.
11. Luminaire not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing to the ceiling.
13. This fitting is only suitable for fixing to the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps which do not exceed the maximum specified wattage.
16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
18. Cracked or broken safety glass has to be replaced immediately. Use only manufcturer approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class I Electrical safety guaranteed by the main insulation and an additional protective conduct- tor (earthing) connected with the metal frame of the lamp. Earthing is obligatory.
22. Class Il Electrical safety guaranteed by the main insulation and a double or reinforced insulation. Earthing is not necessary.
23. Class Ill Electrical safety guaranteed by very low power supply (less than 50 Volt). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,5 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Totally protected against dust infiltration.
31. Not protected.
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40. Luminaire not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

IDEAL LUX s.r.l.
Via Taglio Destro 32
30035 Mirano (VE) Italy
www.ideal-lux.com

IDEAL LUX Warehouse
Via delle Industrie, 8/D 30036 Santa Maria di Sala (Venezia) 8.00 – 12.00 / 13.30 – 17.00

FAQ

• What should I do if the lamp does not turn on?
  • If the lamp fails to turn on, try replacing the fuse with a new one to ensure proper functionality. If issues persist, consult a qualified electrician for further assistance.
• Can I replace the LED light source?
  • No, the LED light source is not replaceable. Do not attempt to disassemble the light fixture.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>