Rowenta SO6020F0 Hot Air Convector Instruction Manual

: June 5, 2024
: Rowenta

Table of Contents

WARNINGS
**VERY IMPORTANT
USE IN THE BATHROOM (protection against splashing with water)
VOLTAGE
SAFETY
OPERATION
INSTALLATION ON WALL
CLEANING
STORAGE
IN THE EVENT OF PROBLEMS
ENVIRONMENT PROTECTION FIRST!
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

www.rowenta.com![Rowenta SO6020F0 Hot Air Convector

fig](https://manuals.plus/wp-content/uploads/2022/05/Rowenta-SO6020F0-Hot- Air-Convector-fig-550x453.png)

A. Function-selection switch
B. Temperature-control switch: Thermostat
C. On/Off indicator
D. “Signal protect” indicator
E. Air intake screen
F. Air outlet screen
G. Transport handle
H. Power cord holder
I. Outlet compartment
J. Foot-operated power cord rewind
K. Wall bracket
L. Upper wall-bracket hook
M. Lower wall-bracket hook

Please read carefully and keep in a safe place.

WARNINGS

For your safety, this appliance complies with the applicable standards and regulations or commercial (Low Voltage, Electromagnetic Compatibility, Environmental Directives, etc.)
The warranty will be invalid in the event of damage arising from incorrect use.
Do not place your appliance directly beneath a wall socket.
Do not operate your appliance in a dusty room or if there is a risk of fire.
Each time before use, check that in general the appliance is in good condition, as well as the plug and the cord.
Never insert any objects inside the appliance (e.g.: needles)
If the power cord is damaged, it must be changed by the manufacturer, the After Sales Service or a similarly qualified person in order to avoid any danger.
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
Do not pull the power cord or the appliance, even to unplug it from the wall socket.
Completely unwind the cord each time before use.
This product has been designed for domestic use only. Any commercial use, inappropriate use or failure to comply with the instructions, the manufacturer accepts no responsibility and the guarantee will not apply.

**VERY IMPORTANT

**

WARNING: To avoid risk of overheating, NEVER PLACE OBJECTS ON TOP OF THE UNIT.
Do not use the unit in the proximity of flammable objects or products (curtains, aerosols, solvents, etc.)
Never use the unit in an inclined or horizontal position.
Do not use this appliance near a bath, shower, sink or swimming pool.
NEVER ALLOW WATER TO PENETRATE THE APPLIANCE.
Do not touch the appliance with wet hands.
In the event of a long absence: turn the button A (fig.4b/4c) to the initial setting (SO6020/SO6030) and unplug the appliance or turn the button B (fig.4a) to the initial setting (SO6010) and unplug the appliance.

USE IN THE BATHROOM (protection against splashing with water)

This “ IP21 “ unit has been specially designed so that it can be used in any room in your house, including those where there is a risk of water being splashed onto it from above (kitchen, bathroom, etc.).
However, the electrical installation in the room, the installation of the unit and the way the unit is used must all comply with the safety standards in force in your country.
Your appliance must be installed so that the switches or other control elements cannot be touched by the person in the bath or shower.

VOLTAGE

Before first use, make sure that the voltage being used corresponds to what is indicated on the unit and that the electrical installation is adapted to the power level indicated.
Your appliance can be used with a power plug without an earth connection. It is a class II appliance (dual electrical insulation ).

SAFETY

SO6010/SO6020:

In the event of abnormal overheating, a safety device shuts down the appliance and then automatically restarts it once it has cooled. If the fault persists or gets worse, a thermal fuse shuts the appliance down definitively and it must then be taken to an approved service center. SO6030:
In the event of abnormal overheating, a safety device shuts down the appliance and then automatically restarts it once it has cooled. If the fault persists or gets worse, a thermal fuse shuts the appliance down definitively and it must then be taken to an approved service center.
If the unit tips over, a safety device automatically turns it off. When placed back in an upright position, it will once again begin to operate. In both cases, a warning beep will occur and the “Signal Protect” indicator (D) will light up.

OPERATION

Before turning the unit on, make sure:
– it is positioned as described in these instructions,
– that it is placed in a flat and horizontal position, and;
– that the air intake and outlet screens are free of all obstacles.

• Function Selection (SO6020/SO6030):
Select the desired function by turning switch (A) to line up the marking on the switch with one of the following symbols:
0 : on
: Cooling
• : 1200W
• • : 2400W

Indicator:
– On/Off indicator (C fig.4), lights up when the unit is turned on.
“Signal Protect” indicator (D fig.4c), lights up in case of overheating or if the unit tips over. Only for Mod.SO6030.
Thermostat:
Adjust the temperature setting, according to your own comfort, by turning button B (fig.4).
Frost-free setting
: This setting enables you to automatically maintain the temperature above 0°C in a normally insulated room, whose volume corresponds to the power of your appliance.
SO6010: To do this, plug in your appliance and turn button B (fig.4a) so that the marker is opposite the “ *”.
SO6020/SO6030: Plug in the unit and turn switch B to line up the marking on the switch with the` “ *”` and turn to switch A to select one of the following: • 1200W or •• 2400W
Cold ventilation setting : (SO6020/SO6030) This setting enables you to use your fan heater as a fan in the summer.

INSTALLATION ON WALL

The unit is made for wall use.
It must be positioned correctly and in a vertical orientation (switch located in the upper zone; see fig 5) The instructions for bathroom installation and minimum distances described in fig. 5 must be respected. You must use the provided wall brackets (K) to attach the unit to the wall.
Wall Attachment: see fig. 6a.

Attach the wall bracket with appropriate screws and plugs following the direction of the arrow.
Insert the upper wall-bracket hook (L) in the unit’s transport handle (G), and clip the lower wall-bracket hook (M) onto the unit.

Taking Down the Unit: see fig.6b.

Maintain a solid grip on the unit and push down upon the lower tongue of the wall bracket.
Pull the unit out from the bottom.
Lift the unit up and remove it from the upper hook.

CLEANING

Your appliance must be unplugged before proceeding with any cleaning work.
You can clean it with a slightly damp cloth.
IMPORTANT: Never use abrasive products which might damage the appearance of your appliance.
We recommend that you clean the air inlet and outlet grills at least once a year; (clean with a vacuum cleaner if necessary).

STORAGE

It is extremely important that the unit be allowed to cool down before it is put away.
The power cord can be rewound for storage (see fig.3).
When you are not using your appliance, store it in a dry place.

IN THE EVENT OF PROBLEMS

Never dismantle your appliance yourself. A poorly repaired appliance may be dangerous for the user.
Before contacting one of our Approved Service Centres (see enclosed list), ensure that:
– the appliance is set to normal operating mode;
– the air inlet and outlet grills are totally clear.