aiwa PJ-882 USB Rechargeable Blender User Manual

aiwa PJ-882 USB Rechargeable Blender

Important Safety Precautions

Please heed all safety precautions when operating this product.

Warning

• May cause serious & fatal injuries.
• May cause danger & hurt/damage the product.
• Device Shelf Life: Up to 5 (Five) Years.
• Please do not use this product above the recommended shelf life due to wear and tear causing mechanical failure.

Please heed all safety precautions stated in this user manual.

• Attention
• Warning Prohibition
• Do not allow water contact
• Do not disassemble
• Do not touch
• Operate according to instructions
• Unplug power source
• Do not operate with
• wet hands Cutting Hazard Do not expose to heat
• Do not attempt to disassemble or alter the product
• Do not expose the product to fire, flammable & any other sources of heat. Doing so may cause fire-related accidents.
• Do not use any spray paint, oil, insecticide on the product.
• Do not continue using this product if high motor friction issuspected due to low machine lubrication.
• Approach a certified mechanic or repair specialist to have the problem diagnosed or stop using the product for safety reasons.
• Do not touch the blade directly with your bare hands.
• Do not place the product near to fire, flammable & any other sources of heat. Doing so may cause fire-related accidents.
• Do not turn on if product is not closed/assembled properly.
• Do not place any hard objects into the juicer.
• Do not move the juicer around necessarily during operation.
• We recommend to place the blender in a fixed location during usage.
• Do not move the juicer around necessarily during operation.
• We recommend to place it in a fixed location during usage.
• Please clean the juicer thoroughly after usage. Allow it to dry
• completely before assembling and storing it away.
• Do not over fill the juicer. This will cause liquid leakage.
• Do not the juicer unattended during operation.
• This product is not intended for use by persons with reduced physical, mental, sensory capabilities (including children), or lack of experience, unless under the supervision of a person/adult responsible for their safety.
• Do not move the juicer around necessarily during operation.
• We recommend to place the blender in a fixed location during usage.
• Do not pour any liquids that are above 40 degrees Celsius into the juicer. This will severely damage the cup.

Important Safety Precautions

• Do not place your hands/ fingers on the blade.
• Always hold the juicer by the blender body.

Note

• Please charge the new juicer for four (4) hours before first-time usage.
• Charge the device every thirty (30) days.

Product Overview

1. Cup Body
2. Magnetic Sensor Strip
3. Blade
4. Blender Body
5. Display
6. ON/OFF Button
7. Type-C Charging Port (with waterproof seal)
8. Anti-Slip Suction Cup

Display Guide

• Juicer is secured tightly. Press the Power button to begin the operation
• Juicer is not twisted close tightly enough, please tighten the cap.
• The blender motor is stuck due to a hard object / too many substances.
• Please remove the stuck object, turn off and try again later.
• Device is charging
• The device is fully charged
• Low battery
• Faulty Battery (Display flashes between Lo & Er alternately) Battery unit overheating.
• LED Display Color: Blue
• Product Name: Portable Wireless Juicer Voltage: DC 5V
• Charging Current: <1A
• Rated Power: 120W
• Peak Power: 180W
• Current: 5-20A
• Current Cut-Off Load: 23A
• Battery: 4000mAh/3.7V X2
• Motor: DC7.4V
• Single Operation Duration: 20 sec Max RPM: 20000 Rpm±15%
• Water Rating: IPX6
• Recommended Water Level: <50mm Capacity: 460ml Max
• USB Charging Cable: Type-C (80cm) Blade: 304 Stainless Steel, toothed Blender Body: ABS
• Cup Body Lid: PP
• Cup Body: Tritan
• Frosted finish
• Dimensions: 80x80x225mm
• Weight: 0.47 Kg

Do not place the product near to fire, flammable & any other sources of heat. Doing so may cause fire-related accidents.

User Precautions

1. Please abide by all safety precautions as stated in this user manual
2. Please charge the juicer for Four (4) hours prior to first-time usage.
3. Do not open the juicer during operation or place your
4. fingers/any other hard objects into the juicer.
5. Please ensure juicer is turned off before cleaning.
6. Do not submerge the blender body in water while cleaning.
7. Maximum single operation time: 20 Seconds.
8. When the fruit pieces are too large, the juicer’s motor will stop automatically to prevent any mechanical failures. Please
9. make sure the device is turned off while removing.
10. Press the Power button to begin operating again.
11. Do not place this juicer in an automatic dishwasher.
12. Do not use any harsh abrasives or harsh chemicals to clean this juicer.
13. This juicer is built for blending soft fruit pieces only. Not
14. suitable for meat, ice cubes, beans or any other hard food.
15. Please use this device with care.
16. Please use a brush or the dedicated brush provided to clean the blades.
17. Avoid touching the blade with your bare fingers.
18. Do not touch the blade or hot motor assembly directly after usage.
19. Stop all usage if any smoke emits from the product.
20. Do not attempt to remove the in-built battery from the juicer.
21. The blender body is designed specifically to fit the given cup body.
22. Do not use them with other products/cups / bodies.
23. Please charge the juicer every thirty (30) days.

Important User Guidelines

Please charge the juicer for Four (4) hours prior to first time usage. Juicing Guide:

1. Twist open the cup, prepare 1.5cm x 1.5cm sized fruits, add adequate water to one’s preference. We recommend just enough water to match the height of the fruit cubes.
2. Close the juicer tightly and press the power button once.
3. The juicer will automatically stop after 20 seconds. This process can be repeated.
4. Make sure the juicer is turned off after operation. Wash the juicer thoroughly.
5. Prepare 1.5cm x 1.5cm sized fruit cubes. Please remove all hard objects not limited to but including seeds, tough skin etc.
6. Capacity Guide: 60% of cup (Fruits) , add water. 80% of the Cup utilized. Do not fill more than 80%of the cup’s capacity.
7. Close the juicer tightly until the ‘88’ display lights up and press the power button once. The juicer will automatically stop after 20 seconds. This process can be repeated.
8. Make sure the juicer is turned off after operation. Wash the juicer thoroughly.

User Guide with pictures

1. Open the juicer.
2. Prepare 1.5cm x 1.5cm sized fruit cubes. Please remove all hard objects not limited to but including seeds, tough skin etc.
3. Capacity Guide: 60% of cup (Fruits) , add water. 80% of the Cup utilized. Do not fill more than 80% of the cup’s capacity.
4. Close the juicer tightly until the ‘88’ display lights up and press the power button once. The juicer will automatically stop after 20 seconds. This process can be repeated.

Washing Guide
Important: Do NOT submerge the blender body to water. Avoid exposing the charging port to water. Any misuse due to user error is not covered by warranty.

1. Remove the cup body and wash.
2. Only wipe the bottom of the blender body.
3. Rinse the blades in a manner where the blender body is not fully exposed to water.

Troubleshooting

1. Can’t be turned on. No Display shown on LED Display.
2. Please tighten the cup with the blender body again.
3. Can’t be turned on.
4. Lo Display: Low battery
5. Lo / Er: Faulty Battery (Please send it for repair / exchange / get a new replacement)
6. “EL” Display.
7. The blender motor is stuck due to a hard object / too much substances.
8. Please remove the stuck object, turn off and try again later.
9. “Er” Display.
10. Juicer is not twisted close tightly enough, please tighten the cup.
11. The juicer is leaking Check the rubber seals around the blender body edges and make sure they are properly in placed.
12. Weird noise during operation Check the rubber seals around the blender body edges and make sure they are properly in placed.
13. Weird noise during operation Please make sure the product is being placed on a stable surface or lessen the amount of substances in the cup.
14. Display Guide
15. Juicer is secured tightly. Press the Power button to begin operation

• Er: Juicer is not twisted close tightly enough, please tighten the cup.
• EL: The blender motor is stuck due to a hard object / too much substances.
• Please remove the stuck object, turn off and try again later.
• Ch: Device is charging.
• FL: Device is fully charged.
• Lo: Low battery.
• Lo / Er: Faulty Battery (Display flashes between Lo & Er alternately) Ec: Battery unit overheating.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>