EVERNARY SOS01D Flashing and Vibrating Caregiver Pager User Manual
- June 5, 2024
- EVERNARY
Table of Contents
User Manual for Flashing and Vibrating Caregiver Pager
Brief introduction
The wireless caregiver pager is specially designed for patients, the disabled,
elderly, pregnant women or children. Simply press call button to alert the
caregiver via the wireless fash or vibrating receivers.
Main Features:
- 100 meters working range in open air,
- The flashing receiver has 4 working modes for different people;
- The Plug-in receiver and portable vibrating receiver works together,
- 52 melodies, 4 adjustable volume levels;
- Learning code and expandable, more sensors and receivers can be easily added by users;
- Easy installation and operation
- Low power consumption.
Structure diagram of products
Flashing receiver
Vibrating receiver (Portable)
Panic button (Transmitter)
Specifications
Parameter| Flashing receiver| Vibrating receiver|
Transmitter
---|---|---|---
Voltage| AC 110V/ 220V| 3V DC power (AAA batteries*2)| CR2032 battery
Operating temperature| -15 °C-55°C| -15 °C-55°C| -20 °C-55°C
Transmission distance| 100 m in open air
Operating frequency| 433.92MHz ±200KHz
Volume| 25-110dB
Power consuption| 0.1 W
Notice before installation
Caregiver Pager With Call Buttons relies on wireless radio technology which is
subject to physical and environmental considerations. These products do not
have an out of
range function and as such should be tested periodically in the setting in
which they are to be used to understand their area of efective operation.
- Radio signal will be affected by metal, wall, concrete and barrier etc., the test distance in open air is 50-100 meter, generally, ral operating distance through secunty doors, walls can be about 30-50 meter, which depends on the specific environment.
- Please first test whether the operation range you choose is proper before install them.
- Please don’t place the transmitter close to other metal devices, if the operating range is short, please change the location of transmitter.
- Please install the receivers away from induction cooker, television and horn where there is interference of magnetic and signal.
- The shorter the straight-line distance between receiver and transmitter is, the better performance of signal through wall is.
- The product can be used directly without any settings if you do not add more receivers or transmitters and not change the default ring tone (Ding Dong).
Installation Methods
For Receiver:
Just plug flashing receiver into the standard outlet in room, then it will
flash or sound Ding Dong after getting signal from the transmitter.
Put 2AAA batteries into the vibrating receiver, and then it will vibrate and
sound Ding Dong’ after getting signal from the transmitter.
Please note that learning code doorbell needs re-matching if you want to add
more transmitters or re-choose the ring tone.
For Transmitter:
NOTE: Please first test whether the operating range you choose is working
Panic button is easy carry, it can be hung around the neck as pendant or put
in pocket, neck strap is included
Warning
- You’d better use the high quality battery, avoid using the ones with short life and easy leakage of electrolyte.
- Be sure to protect the precision electronic components, non-professionals are not allowed to open it for maintenance.
- Avooid installing the product to exposure place under sun and long rains directly.
- Correct use of the products helps to effectively extend the lifetime.
- The device is not a substitute for visual monitoring by a caregiver, it is not suitable for all individuals, other devices may be required. The manufacturer does not claim that this device will stop eiopment and/or stop falls, it is designed to augment caregiver’s management program. Test this device before each use.
Operating Instructions
-
Volume Selection
There are 4 levels of volume for choosing. Find the volume control button on the left side of the receiver. Press this button repeatedly to get the desired volume level, -
Music/Chime Selection
There are 52 different ring tones. You can pair your receiver and re-choose the musical same lime as the next step (3): -
Pairing (matching) a Receiver with transmitter and change music a)Set Receiver into Configure Mode – Press Volume Change Button on the receiver for 5 seconds until it starts flashing and makes a sound to indicate ready status.
b)Next, press Melody Change Button to choose the ring tone you like
c)After that, trigger sensors or buttons, receiver will ring every time it gets a signal. Trigger again to confirm the settling. seconds until the LED stops flashing. Or you can unplug the Receiver to
d)Finally, exit from Configure Mode – Press Volume Change Button for 5 exit.
e)Clear the settings-press melody change button for 5 seconds
NOTE: After clearing operation, the receiver will automatically connect with the FIRST button or sensor you triggered and play the default ring tone (Ding Dong). -
Adding additional receivers or sensors
Repeat steps 1a-b-c-d for additional receivers or sensors if needed. Each Receiver can be configured with the same or different ring tones in this way.
Products list
2 receivers, 1 button with battery, strap and user manual.
FCC Caution：
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>