EVERNARY K-100A Caregiver Pager Wireless Calling System User Manual
- June 12, 2024
- EVERNARY
Table of Contents
EVERNARY K-100A Caregiver Pager Wireless Calling System
Product Information
The Caregiver Pager is a device that allows caregivers to receive notifications and alerts from transmitters. It has the ability to register different ring tones and adjust the volume. The pager can be set to either a short ring or a long ring mode. It also has the capability to restore factory settings if needed.
Restore Factory Settings
To restore the factory settings of the Caregiver Pager, follow these steps:
- Hold down the volume key for about 10 seconds until the red light stays on continuously.
- The red light indicates that the factory settings have been successfully restored.
How To Register SHORT RING
To register a short ring tone on the Caregiver Pager, follow these steps:
- Select the desired ring tone by pressing the key.
- Hold down the volume key for about 3 seconds until the red light quickly flashes.
- Press a transmitter to register.
- A “ding-dong” sound will indicate successful registration.
- The pager will automatically exit to standby mode after registration, unless no action is taken within 6 seconds.
Note: In standby mode, you can adjust the ring tone by pressing the key. Pressing the key will overwrite the current ring tone with the new one, regardless of whether the transmitter is pressed or not.
How To Register LONG RING
To register a long ring tone on the Caregiver Pager, follow these steps:
- Select the desired ring tone by pressing the key.
- Hold down the volume key for about 3 seconds until the red light quickly flashes.
- Continue to press and hold the volume key until the red light turns into a slow flashing state.
- Press a transmitter to register.
- A “ding-dong” sound will indicate successful registration.
- The pager will automatically exit to standby mode after registration, unless no action is taken within 6 seconds.
Note: In standby mode, you can adjust the volume but cannot select the ring tone. The volume can be adjusted using the volume key. There are 4 levels of adjustable volume, and there is no mute mode available.
Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment should be installed and operated with a minimum distance of 0cm between the radiator and your body.
How To Register SHORT RING
The ring will stop automatically after two consecutive reminders.
- After selecting the ring tone what you need by key, hold down the volume key for about 3 secs until red light quickly flash.
- Then press a transmitter to register, a ding-dong sound that means the registration is successful, then automatically exit to standby. Or no action within 6 secs after registering, it will automatically exit to standby.
Provided that the transmitter is registered :
- In standby, you can adjust the ring tone by pressing the key;
- If you press the key, the current ring tone will be overwritten and updated to the new one, regardless of whether the transmitter is pressed or not.
How To Register LONG RING
The ring will keep cycling unless the call is cancelled manually.
- After selecting the ring tone what you need by key, hold down the volume key for about 3 secs until red light quickly flash. Continue to press and hold until the red light turns into a slow flashing state.
- Then press a transmitter to register, a ding-dong sound that means the registration is successful, then automatically exit to standby. Or no action within 6 secs after registering, it will automatically exit to standby.
Note: You can press and volume key to stop the call. In standby, you can adjust the volume but can not select the ring tone. 4 levels adjustable volume, no mute mode.
Restore Factory Settings
Hold down the volume key for about 10 secs until the red light is long, indicating that the factory settings have been successfully restored.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuing t to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different f rom that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>