HUINA 1550 Remote Control 1:14 Electric Excavator Instruction Manual

HUINA 1550 Remote Control 1:14 Electric Excavator

Remote control car battery installation and charging instructions

Open the remote control car battery cover, install 7.2V charging batteries set and close the batteries cover, tighten the sorews

1. Connection LED lights lit;
2. Charging LED lights flash slowly:
3. Full LED light goes out:

The remote control battery installation instructions

Open the remote control battery cover, install 2x 1.5 “AA” batteries, and love the battery cover, tighten the screws. When the indicator light of the remote control is not indicated low battery, replace the battery

Frequency Pairing

This product uses a 2.4GHe frequency remote control before the play should be on the remote control and the vehicle frequency matching: remote control cars and remote control aher installing the battery power is turned on At this point the remote control will automatically find the frequency. light is blinking When the remote control light stops flashing Frequency matching is completed, the remote control function can be used normally

Remote Control Operation

1. 00 Direction joystick:
2. 00 Direction joystick:
3. Shake the “simultaneous forward” the car forward; crank “while back” the car back;
4. The left stick forward, the right stick backward, excavators, turn right
5. Left joystick backward, right stick forward, excavators turn left
6. Left arrow key table: Key control table left rotation:
7. Right table Arrow keys: right-button control rotary table:
8. Bucket control keys: Control the bucket rise and fall;
9. Big arm (B) Segment control keys: Big arm (B) segment rise and fal
10. Big arm (A) Segment control keys: Big am (A) segment rise
11. Big arm (A) Segment control keys: Big arm (A) segment fal;
12. Programming key
13. Press the programming button for 3 seconds to enter the programming mode, then the functional operation of the excavator, press the programming button, complete the programming mode,
14. On completion of the programming mode and then press the programming button at the programming mode start
15. Press any key to release the programming mode
16. Mute switch button: (Press: the music, the lights start press again: the music, the lights stop)
17. Auto Demo key: Auto Demo excavator each function; Remote power switch;

Battery use instructions and Cautions

1. Batteries must be inserted with colored polarity. Do not mix different types of batteries or new and used batteries.
2. Only the recommends or the same types of batteries can use with the car.
3. The supply terminals can not be short-circuited.
4. Exhausted batteries must be removed from the car
5. Non-rechargeable batteries should not be charged. The batteries are only to be charged under adult supervision.
6. The batteries must be removed from the toy before charging
7. The user needs to be regularly examined for the damage of the wire, and plug. shell and related part, in the event of such damage, stop using until the damage has been repaired. Do not break off the antenna of the controller, part may cut you.
8. The R/C car should use 7.2V chargeable battery set RIC controller should use 2×1.5V “AA” alkaline non-rechargeable battery. the sharp

FCC STATEMENT

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference ina
residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help
• Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>