Shenzhen Tfiretek Technology X5 Projector User Manual

USER MANUAL
Projector X5
For more questions, please consult online customer service.

Notice
Please read this user manual carefully before use.
Shenzhen TFIRETEK Technology Co., Ltd.

Specification

Package contents

Safety Instructions

WARNING:

1. To reduce the risk of fire or electric shock, do not expose this device to rain or moisture. The device shall not be exposed to dripping or splashing and objects filled with liquids, such as vases, shall not be placed on the apparatus.
2. The plug of the power cord set is used as a disconnect device, the disconnect device shall remain readily operable.
3. To reduce the risk of electric shock, do not remove the cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.
4. The plug of the power cord set is used as the power interrupting device. Please pay attention to safety plug and pull and convenient operation.
5. Do not expose the appliance to naked flame sources (for example, lighted candles). 6. Do not install the appliance in a confined space, such as a bookcase or built-in cabinet.

Correct Disposal of this product. This marking indicates that this product should not be disposed of with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer or service operator where the product was purchased. They can take this product for environmentally safe recycling.

FCC Warning Statement

FCC Radiation Exposure Statement:
The antennas used for this transmitter must be installed to provide a separation distance of at least 20cm from all persons and must not be co- located for operating in conjunction with any other antenna or transmitter. This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions (1) this device may not cause harmful interference. and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

1. Reorient or relocate the receiving antenna.
2. Increase the separation between the equipment and receiver.
3. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for help.

Hazardous Substances Table

0: It indicates that the content of the toxic and hazardous substances in all homogeneous material is less than the specified limit by Directive2011/65/EU (RoHS)
x: It indicates that at least one content of the toxic and hazardous substance in all homogeneous material is beyond the specified limit by Directive2011/65/EU (RoHS) This table shows the toxic and hazardous substances when manufacturing this device, hazardous substance information is based on information from the supplier as well as internal inspection. In some parts, the hazardous substances cannot be replaced with current technologies, Tfiretek is always doing its best to improve the quality of the product.

Important Safety Notes

To ensure the performance and stability of the projector, please place it horizontally and leave a space of about 30cm between the projector and the wall.

|
---|---
Do not install in places with poor ventilation| Do not install in high temperature or humid places
|
Do not block the vents| Do not install in dusty or smoky places

Projector Accessories

Notice: Do not look directly at the lens to prevent eye injury!

Remote Control Button Function

Product name: Remote control.
Model: V1 Parameters:
DC 3V , AAA*2

Voice pairing method

1. Press and hold the left & right direction buttons at the same time for 3-5 seconds until! the red light flashes.
2. Open Settings — Remote Control & Accessories —click the name of the Voice Assistant to connect (as shown in the pictures)

Due to the continuous updates of the design, the appearance of the machine may be slightly different from that shown in the above pictures. please refer to the actual product.

Power-On/Off Operation

1. Power connection
   

2. Boot & Shutdown

Projection Distance Reference & Screen Adjustment

1. Projection distance reference
   

2. Sharpness adjustment

1. After the machine is placed horizontally, turn the focusing ring up and down to adjust the picture to be clear.
2. If the machine installed tilted, please set the keystone correction to adjust. If unable to get satisfactory sharpness, move the machine slightly forward or backward.

Warn: The machine filter and air outlet must not be blocked or too close to the wall. Clean the filter regularly every month to prevent clogging.

Connection settings

WiFi connect ( For Android devices and Cast devices)

1. Open Settings — Network & WiFi ( picture 1 ) to enter the WiFi settings page ( picture 2 )
2. Choose the WiFi option and enter passwords to connect.

Tips:

1. Click “Next” on the software keyboard to connect WiFi after passwords are entered.
2. If the pop—up window of “Problem with Authentication” appears, it means that the password is incorrect. If the pop—up window of “Saved”, it may be that the router’s WiFi settings are limited. It is recommended to check as follows:
   A. Turn off the WiFi for seconds and turn it on again to connect.
   B. Reboot the router and connect again, try to reduce the connected devices.
   C. Connect to the mobile phone hotspot to check if the projector WiFi works properly.

HDMI & Bluetooth Connection

HDMI connection

1. Press the “Switch” button on the projector or the signal button of the remote to choose the signal source. (In picture 1 ).
2. Only on the Android interface: open Settings — Signal ( picture 2).

Due to the continuous update of the design, the software interface may be slightly different from this picture, please refer to the actual product.

ScreenCast for Android Phone ( support Android 5.3 and above )

1. Open the “Miracast” App as below picture. The local device name is “Android_XXXX”
2. Open the Wireless Cast on an Android phone to search available devices, and click the “Android_XXXX” option to connect.
3. Click on the prompt box to accept the screencast connection. If the screen is synchronized, means screencast is completed.

Wireless Screen Mirroring for iPhone

1. Please ensure the iOS device and projector are connected to the same network.
2. Open the “CoolAirMirror” App on the projector.
3. Open the Screen Mirroring from the control center on iPhone.
4. Search for available devices.
5. Connect to the “ByteFly—XXXXXX” option to start the mirroring screen.

Connection Settings (Introduction of different versions)

1. Projector—Multimedia version
   The Multimedia version projector can play content from HDMI input or USB transmission from a laptop or set-top—box.

2. Projector—Cast version
   Cast version projector can both play HDMI input content and the content shared by mobile phone screen mirroring.

3. Projector—Smart version
   Smart projector available to preinstall various applications to play network video.

Filter Cleaning

1. Filter Cleaning

Pull out the filter and clean the dust on it, then install it back.

Projector Common Troubleshooting

1. The remote control is insensitive or unresponsive
   — Please check if the batteries are installed properly.
   — Please replace with new batteries.
   — Please aim the remote control for the projector to operate.

2. Unable to boot up
   — Please check if the power cord is connected properly and if the power light is on. Try to unplug and plug the power if the projector still cannot boot up.

3. Black screen or abnormal picture after booting for a while
   — Please check if the vents are blocked.
   — Please check if the cooling fan is working properly. If abnormal, please return for repair.
   — Please try to reboot the projector.

4. No network connection
   — Please check if the WiFi is connected properly and if the WiFi signal is good.
   — Please connect the hotspot or smartphone to verify if the router is working properly.

5. Blurry display
   — Please check if the lens is clean.
   — Please use the focusing ring to adjust the sharpness.
   — Please check if the environment is too bright.

6. Screen freeze
   — Please reboot the projector to test again. If the screen still freezes, please turn it off for 10 minutes and turn it on again.

Manufacturer Information:

Shenzhen TFIRETEK Technology Co., Ltd. 4 Floor, Plant 5, Detail Industrial Zone, No., 496, Huarong Road, Langkou Community, Dalang. Street, Longhua District, Shenzhen City, China
Hereby, Shenzhen TFIRETEK Technology Co., Ltd. declares that the projector X5 is in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet address: http://www.tfiretek.com/

European Agent Information:
Name: eVatmaster Consulting GmbH
Add Bettinastr. 30,60325 Frankfurt am Main, Germany
Zip Code: 60325
E-mail: contact@evatmaster.com
Tel: +496995179070

Warranty Card

1. This projector supports Three Guarantees Service. Warranty for 1 year from the date of purchase. (non-artificial damage).

2. Within warranty, we support warranty service for any failures caused by product technology.

3. The following situations are not covered by the warranty:
   — Accessories except for the projector.
   — Products that have been disassembled and repaired without permission.
   — Damage caused by external force and other natural disasters.

4. When the product fails, please contact the dealer or supplier in time to arrange for repair within this warranty card.

5. This warranty liability is limited to product failure repairs within the warranty period.

Warranty Card

Client Name:_
Client ID:___
Purchase shop:__
Client Phone Number:____
Return Address:_____
Fault description
(For a quick repair, please describe in detail):

FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference. and (2) this device must accept any interference received, including interference that may cause undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy. if not installed and used in accordance with the instructions. may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on. the user is encouraged to try to correct the interference by one or more of the following measures:
– Reorient or relocate the receiving antenna.
– Increase the separation between the equipment and receiver.
– Conned the equipment into an outlet on a circuit different from that to which the receiver is connected.
– Consult the dealer or an experienced radio/TV technician for help with an important announcement

Radiation Exposure Statement
To con-ply with FCC RF exposure compliance requirements, this grant is applicable to only mobile configurations. The antennas used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>