BOSS AUDIO SYSTEM 77206OM Bolt Portable Bluetooth Speaker User Guide

77206OM Bolt Portable Bluetooth Speaker
User Guide
BOLT

77206OM Bolt Portable Bluetooth Speaker

Power on the speaker.
Long press to turn on / off the Emergency lighting.
Attention. Do not look directly into the beam!

Charge the speaker until the red LED light turns off. ‘
Tips: When you hear a voice prompt: Battery is low, please recharge the speaker. To save power, the speaker turns off automatically after 9 minutes of inactivity unless the AUX cable is plugged in.

BOLT is sold in pairs to let you enjoy the true stereo sound quality without using the wires (TWS). You can also use each unit individually as an independent Bluetooth speaker.
Long press to power on. The Bluetooth indicator flashes blue s owly, indicating that the speaker is in pairing mode.
Double click on either speaker to set up a True Wireless connection. The two speakers will pair with each other automatically after 5 to 10 seconds.
Once paired, the True Wireless will reconnect automatically when both speakers have turned on again.
Tips: After a successful connection, you can use the +/- and NI keys on either speaker to control both speakers at the same time. You can double-click click on either speaker to disconnect the True Wireless connection.

1. After TWS is paired, you can connect your mobile device with the main speaker.
   Select “Boss Audio Systems Bolt” from the available devices (enter the password ‘0000’ if necessary) to start pairing and connecting with the speaker.

2. After successful connection, the Bluetooth indicator on the main speaker turns solid blue and you hear a voice prompt “Bluetooth connection successful”.

Tips: This speaker supports automatic connection with a previously paired device after power-off and power-on again. If no paired device is found, the Bluetooth LED will flash slowly for 9 minutes before automatically turning off.
You can double-click to enter manual pairing mode. In this way, you can pair the speaker with a new Bluetooth device. You can reset the speaker/ clear all BT and TWS connections by pressing the button inside the AUX IN port using a non-mental pin.

Press o cycle through modes. The modes available are Bluetooth, AUX-IN, USB and SD. In AUX/USB/SD mode, each speaker works independently.

Play music on your device paired and connected with the speaker. While music is playing:
• Hold +/- to adjust the volume.
• Press +/- t o skip to the next/previous track.
• Press to pause or resume music playing.

When you make a call or there is an incoming call, you can use the speaker as a speakerphone.
When there is an incoming call, you can press once to receive the call or long-press to reject the call. To end the call, press
Tips: Music playing is paused during a call and resumed automatically when the call ends.
To disconnect the current Bluetooth connection, double click In stereo (TWS) mode, double click to disconnect the TWS connection, and switch to mono mode. To switch back to stereo mode, Double click on the speaker with solid blue light.

Important Safety

WARNING: The apparatus shall not be exposed to dripping or splashing and objects filled with liquids, such as vases, shall not be placed on the apparatus.
WARNING: Where the mains plug/appliance coupler is used as the disconnect device, the disconnect device shall remain readily operable.
WARNING: The battery (battery or battery or battery pack) shall not be exposed to excessive heat such as sunshine, fire, or the like.
Read these instructions before operation.
Keep these instructions for future reference.
Follow all instructions for installation, use, and maintenance of the device.
To clean the device, disconnect the power first. Clean only with a soft and dry cloth.
To ensure compatibility, only use accessories recommended by the manufacturer.
When the device is suddenly moved from cold to warm surroundings, condensation may form in the housing of the device.
Before use, leave the device in a warm environment until the moisture evaporates.
Keep the device away from heat sources, such as a radiator, heater, oven, amplifier, naked flames or direct sunlight.
No naked flame sources, such as lighted candles, should be placed on the apparatus.
Never block any ventilation openings. Install in accordance with the manufacturer’s instructions.

• Do not expose the device to sand or dust, or cover it with items, such as newspapers, table cloths, or curtains.
• Do not operate the device in an enclosed cabinet. Leave sufficient free space around the device for adequate ventilation.

Do not attempt to repair or service the device yourself. Opening or removing the cabinet may expose you to electric shock, and other hazards. If repair is required, contact your dealer and refer all servicing to qualified service personnel.
Do not use the device if any abnormality occurs. If any smoke or odor becomes apparent, contact your dealer immediately. Do not try to repair the device yourself.
Avoid using dropped or damaged appliances. If the device is dropped and the housing is damaged, the internal components may not function normally. Stop use and contact your dealer for repair. Continued use of the device may cause fire or electric shock. To reduce the risk of electric shock, do not touch any connector with wet hands. Never remove the housing of the device. Never lubricate any part of the device. Never place the device on top of any other electrical equipment.
Notice Modification
Any modification (such as removing the speaker grill) to the device, without prior authorization from the manufacturer, may void your warranty and authority to operate the device
FCC compliance statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur In o particular Installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/P/ technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. and (2) This device must accept any interference received, including interference that may cause undesired operation.
This device complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This device and its antenna is) must not be co-located or in conjunction with any other antenna or transmitter.
Recycling Packaging
Observe the local regulations on how to dispose of the packaging materials.
Instructions for Users on Removal, Recycling, and Disposal of Used Batteries For products with a built-in battery that lasts for the lifetime of the product, removal may not be possible for the user. In this case, recycling or recovery centers handle the dismantling of the product and the removal of the battery. If for any reason, it becomes necessary to replace such a battery, this procedure must be performed by authorized service centers. it is illegal to dispose of any battery with household trash. All batteries must be disposed of in an environmentally sound manner. Contact your local waste-management officials for information regarding the environmentally sound collection, recycling and disposal of used batteries.
WARNING: Danger of explosion if the battery is incorrectly replaced. To reduce the risk of fire or burns, don’t disassemble, crush, puncture, short external contacts, expose to temperature above 60°C (140°F), or dispose of in fire or water.
Copyright Bluetooth®
The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by BOSS AUDIO SYSTEMS is under license.

Specifications

The technical specifications are subject to change without prior notice.

BOLT
All registered and unregistered trademarks are the property of their respective owners.
BOSS INTERNATIONAL GROUP BOSS AUDIO SYSTEMS BOLT All rights reserved.
QSG -Boss Audio Systems BOLT-V3.0

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>