FS IPC201-2M-T Turret Network Cameras User Guide

: June 5, 2024
: FS

Table of Contents

FS IPC201-2M-T Turret Network Cameras
Introduction
Accessories
Hardware Overview Ports
Installation Requirements
Mounting the Camera
Ceiling Mount
Connecting the Power PoE Device
Support and Other Resources
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

FS IPC201-2M-T Turret Network Cameras

Introduction

Thank you for choosing turret network cameras. This guide is designed to familiarize you with the structure of the camera and describes how to deploy the camera in your network.

Accessories

NOTE:
There is no wrench in the accessories of IPC201-2M-T. The installation position map varies according to the different models of cameras.

Hardware Overview Ports

Power Interface
Ethernet Interface
Connect DC 12V power
Connect to Ethernet cable

Installation Requirements

Installation and removal of the device and its accessories must be carried out by qualified personnel.
Store or use the device in a proper environment that meets environmental requirements, including and not limited to temperature, humidity, dust, corrosive gases, electromagnetic radiation, etc.
Make sure the device is securely installed or placed on a flat surface to prevent falling.
Unless otherwise specified, do not stack devices.
Ensure good ventilation in the operating environment. Do not cover the vents on the device. Allow adequate space for ventilation.
Protect the device from liquid of any kind.
Make sure the power supply provides a stable voltage that meets the power requirements of the device. Make sure the power supply’s output power exceeds the total maximum power of all the connected devices.
Take proper waterproof measures in accordance with requirements before using the device outdoors.
Using the device may involve the collection of personal information such as face, fingerprint, license plate number, email, phone number, GPS. Please abide by your local laws and regulations while using the device.

Mounting the Camera

Installing Micro SD Card (Optional)

Insert the Micro SD card (purchased separately) into the camera.
Do not hot plug the Micro SD card after it is inserted. Otherwise the camera or the Micro SD card might be damaged.

Installing Waterproof Connector (Optional)

Install the supplied waterproof components to the Ethernet cable in sequence.
NOTE:
Please use self-adhesive waterproof tape (purchased separately) to protect the cables.

Ceiling Mount

Locate the positions of the holes by pasting installation position map on the ceiling, and lead the cables through the hole on the ceiling.
Drill holes with a diameter of 6 – 6.5 mm and the depth of 30 mm in the marked locations.
Knock the plastic rivets of self-tapping screws into the guide holes and ensure that they are tightened up.
Connect all cables of the ceiling and the camera.
Secure the camera to the ceilingl by leading the self-tapping screws through the guide holes in the base and ﬁx them by using a screwdriver.
Loosen the screw on the base and detach the housing from the base plate with the marks aligned.

NOTE:
The installation process above is concealed installation, during which holes are drilled in the ceiling and tail cable is led out from the top of the camera. Cables are connected and frapped at the ceiling side to prevent messy cables from affecting camera mounting. If open installation is adopted, tail cable is led out from one side of the camera and can be routed from the side groove of the camera.

Mount the housing with install mark aligned.

Adjust the monitoring direction by rotating the camera, tighten the screws.

Connecting the Power PoE Device

Use an Ethernet cable to connect the network interface of the camera to the PoE port on a PoE device, such as a PoE switch.
Power Adapter

Use the power adapter (purchased separately) to connect the power interface of the camera to the local power source.

Conﬁguring the Camera
Step 1: Connect the computer to the camera on the same LAN. Step

2: Set the IP address of the computer to 192.168.1.x. (“x” is any number from 2 to 254.)

Step 3: Open a browser, type http://192.168.1.13 , and enter the default username and password, admin/admin.

Step 4: Click Login to display the web-based conﬁguration page.

NOTE:
You may need to install a plug-in at your ﬁrst login. Please follow the on- screen instructions to complete the installation and then open the browser again to log in.

Support and Other Resources

Download https://www.fs.com/download.html
Help Center https://www.fs.com/service/help_center.html
Contact Us https://www.fs.com/contact_us.html

Product Warranty
FS ensures our customers that any damage or faulty items due to our workmanship, we will offer a free return within 30 Days from the day you receive your goods. This excludes any custom made items or tailored solutions.

Warranty: Turret network cameras enjoy 2 years limited warranty against defect in materials or workmanship. For more details about warranty, please check at
https://www.fs.com/policies/warranty.html Return: If you want to return item(s), information on how to return can be found at
https://www.fs.com/policies/day_return_policy.html