Car Keys Express MAZDA Replacement Remote User Guide

: June 5, 2024
: Car Keys Express

Table of Contents

COMPATIBILITY LOOKUP
PAIRING INSTRUCTIONS
FCC REGULATORY STATEMENT
- OTHER KEYS
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Car Keys Express MAZDA Replacement Remote User Guide

COMPATIBILITY LOOKUP

MODEL	YEARS PAIR	CODE
FORD
Edge	2007-2015	1
Escape	2001-2006	1
Escape	2013-2018	1
Econoline	1999-2013	1
Excursion	2000-2006	1
Expedition	1998-2002	1
Explorer	1998-2001	1
Explorer	2011-2015	1
Explorer Sport	2001-2003	1
Explorer Sport Trak	1998-2006	1
F-Series	1998-2017	1
Fiesta	2011-2017	1
Flex	2009-2017	1
Freestyle	2007	1
Fusion	2011	1
Ranger	1998-2011	1
Taurus X	2008-2009	1
Transit Connect	2010-2013	1
Windstar	1999-2004	1

LINCOLN
Mark LT| 2006-2008| 1
MKX| 2007-2012| 1
MKZ| 2011-2017| 1
Navigator| 1998-2002| 1
MAZDA

B-Series| 1999-2009| 3
Tribute| 2001-2003| 1
Tribute| 2004-2011| 3
MERCURY
Cougar| 1999-2002| 2
Mariner| 2005-2007| 1
Monterey| 2004-2007| 1
Mountaineer| 1998-2001| 1

PAIRING INSTRUCTIONS

Instructions have timing requirements. Waiting too long between steps may result in your vehicle’s computer timing out, requiring you to start over. Once you begin the pairing procedure, be sure to move at a quick and even pace.

PAIR CODE 1

Insert a working key into the ignition.
Turn the ignition from OFF to RUN (without starting the engine) 8 times within 10 seconds, with the 8th time ending in RUN. The door locks will cycle to confirm pairing mode.
Within 20 seconds, press any button on the first remote. The door locks will cycle to confirm pairing.
Within 20 seconds, press any button on the second remote. The door locks will cycle to confirm pairing.
Repeat step 3 for any additional remotes.
Turn the ignition to OFF. Locks will cycle again to indicate the end of pairing mode.
Test all remotes.

PAIR CODE 2

Insert a working key into the ignition.
Turn the ignition from OFF to RUN (without starting the engine) 4 times within 6 seconds.
Turn the ignition OFF. The LED in the clock/trip computer will light up continuously to confirm pairing mode.
Within 20 seconds, press any button on the first remote. The LED in the clock will flash 4 times to confirm pairing.
Within 20 seconds, press any button on second remote.
Repeat step 5 for any additional remotes.
Turn the ignition to RUN (without starting the engine). The LED will turn off to indicate the end of pairing mode.
Test all remotes.

PAIR CODE 3

Close all doors.
Open the driver’s door and press the UNLOCK button on driver’s door panel.
While the door is open, insert a key into the ignition.
Turn the ignition from OFF to RUN (without starting the engine) 8 times within 10 seconds, with the 8th time ending in RUN. The door locks will cycle to confirm pairing mode.
Within 20 seconds, press any button on the first remote. The door locks will cycle to confirm pairing.
Within 20 seconds, press any button on second remote. The door locks will cycle again to confirm pairing.
Repeat step 7 for any additional remotes.
Turn the ignition to OFF. Locks will cycle to indicate the end of pairing mode.
Test all remotes.

FCC REGULATORY STATEMENT

FCC ID: 2AOKM-FD1

47 CFR §15.19(a)(3) THIS DEVICE COMPLIES WITH PART 15 OF THE FCC RULES. OPERATION IS SUBJECT TO THE FOLLOWING TWO CONDITIONS. (1) THIS DEVICE MAY NOT CAUSE HARMFUL INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT ANY INTERFERENCE RECEIVED, INCLUDING INTERFERENCE THAT MAY CAUSE UNDESIRED OPERATION.

Note: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

HELP

For help or assistance, please contact technical support at: 888-598-8910.