ECOTRIC C-STA20LED-W-XXX Electric Bike Owner’s Manual
- June 5, 2024
- ECOTRIC
Table of Contents
- Carton Contents
- Assembling Instruction
- TORQUE SPECIFICATIONS
- Display Instrument Setting
- Troubleshooting
- Warranty Information
- Return Policy
- FAQ
- Battery And Charger Care
- USER MAINTENANCE INSTRUCTIONS
- Safety
- General Warning
- Electrical Parameters
- The Universal Wiring Diagram
- Recording Your ECOTRIC Bike Info
- References
C-STA20LED-BL-XXX
C-STA20LED-W-XXX
C-STA20LED-MB-XXX
(XXX represents any alphanumeric character)
Carton Contents
(x1) ECOTRIC Bike (x2) Keys
(x1) Lithium Ion Battery (x1) Tool Kit
(x1) Battery Charger (x1) Reflector
(x1) Kit Box (x1) Owner’s user Manual
(x2) Pedals
(x1) Saddle
First of all, we would like to thank you for choosing the ECOTRIC electric bike. We believe this technology, with the benefits of electric propulsion, provides you with the perfect vehicle to increase your mobility.
Our brush-less electric hub motor allows you to run errands or commute to work while saving money on gas and reducing your environmental impact on our world. It also allows you to pedal if you want to get exercise along the way.
All this and it is just plain fun to ride!
If you have any concerns, questions, or suggestions about the ECOTRIC electric bike, please contact us at the website where you bought the bike firstly,we will always do our best to serve you. You can also contact us at service@ecotric.com. Again, thanks for choosing ECOTRIC.
PLEASE NOTE:
THIS MANUAL IS NOT INTENDED AS A DETAILED USER, SERVICE, REPAIR OR
MAINTENANCE MANUAL. PLEASE SEEK ASSISTANCE FROM A QUALIFIED TECHNICIAN FOR
SERVICE, REPAIRS OR MAINTENANCE.
WARNING
Electric Bikes can be dangerous to use. The user or consumer assumes all risk of personal injuries, damage, or failure of the bicycle or system and all other losses or damages to themselves and others and to any property arising as a result of using the bicycle.
As with all mechanical components, the bicycle is subjected to wear and high stresses. Different materials and components may react to wear or stress fatigue in different ways. If the design life of a component has been exceeded, it may suddenly fail possibly causing injuries to the rider. Any form of crack, scratches, or change of coloring in highly stressed areas indicates that the life of the component has been reached and it should be replaced.
For replacement parts, technical information and warranty assistance, please feel free to contact us.
YOUR INSURANCE POLICIES MAY NOT PROVIDE COVERAGE FOR ACCIDENTS INVOLVING
THE USE OF
THIS BICYCLE. TO DETERMINE IF COVERAGE IS PROVIDED YOU SHOULD CONTACT YOUR
INSURANCE
COMPANY OR AGENT.
DO NOT DISASSEMBLE, MODIFY OR REPLACE ELECTRICAL PARTS.
Assembling Instruction
Unfold The Bike
Your Electric bike equips with a front V-brake and Rear disc brake.
(1) Carefully take your bike out of the carton and gently rest it in place.
(2) Remove all of the inside cardboard protection and bubble wrap on the bike
(Figure.1-1).
(3) Unfold the bike, Please locate and set aside the kit box containing the battery charger, pedals, and tool kit, etc. (Figure.1-2)
Handle Bar Installation
Unfold the stem, locate the cam lever on the top of the stem, open the cam lever, loosen the nut, and remove the cam lever, slide out the metal cover (Figure. 2-1). Place the handlebar into the groove on the top of the stem, slide the metal cover back into the stem (Figure. 2-2). Adjust the handlebar to a proper angle that fits you, and tighten the handlebar with the cam lever (Figure. 2-3).
Seat Post Installation
1. Please pay attention to the vertical lines on the seat post; it is the minimum insert line/safety line. Please make sure install the post into the frame deeper than the minimum insertion line. It is at the bottom of the seat post (Figure. 3-1).
Warning: It could break the seat tube during riding if the seat post does not install correctly. It is not covered by the warranty.
2. Open the clamp on the seat tube, insert the seat post into the seat tube, adjusting the seat to a comfortable height, tighten the tension adjusting nut, and then press the clamp lever inward toward the seat tube (Figure. 3-2).
Please Note : If necessary, tighten the clamp by twisting the clamp handle clockwise while in the un-clamped position. Then, fold the handle in toward the seat post. This should require a fair amount of force to ensure the seat post is held tight. If necessary, the clamp can be further tightened with a 5 mm Allen wrench while in the clamped position.
Warning: The cam lever may be bent if over tighten tension nut when cam lever un-clamped, it is not covered by warranty!
Pedals Installation
1. Identify left vs. right pedal
There is an “L” or “R” stamped into the axle (the threaded part that looks
like a screw) (Figure. 4-1)
Please Note : They are not the same!! Apply a small amount of grease if
possible
2. Install the left-hand pedal firstly
You will have to screw it in counter-clockwise because the threading is the
reverse of a normal screw. Do this by slowly pedaling the cranks backward. If
the pedal feels stiff, stop, and then re-try, it should feel like a smooth
motion. Please do not use the wrench until you are ready to tighten it for the
final few turns. Tighten it down until you can’t anymore (Figure. 4-3).
Please Note : Hand-tight is not sufficient. Use a tool. If the threads on
the crank are stripped after riding, it means the crank needs to replace. It
is NOT covered by warranty.
3. Install the right-hand pedal
This one threads in clockwise, like a normal screw. Follow the same
principals, as discussed in step 2 for the left pedal (Figure. 4-2).
4. Wipe off any excess grease from around the crank.
TORQUE SPECIFICATIONS
Item|
N.m
---|---
Handlebars|
18N.m (Trail Tracker 12N.m)
Handlebar Stem|
12N.m (Trail Tracker 8N.m)
Seatpost|
Quick Release
Seat|
18N.m
Front Wheel|
18N.m (If Applicable)
Rear Wheel|
30N.m or above
Battery Removing & Charging
1. Remove and install the battery
The keys are tied to the handle on the battery. If the key is on the “Off”
position, push the key in, and turn it to the “Unlock” position (Figure. 5-1),
then pull the battery out of the frame. When mounting the battery, you should
align the battery and the rail on the frame, and slide the battery into the
frame (Figure. 5-2). Then turn the key to the “On” position (Figure. 5-3).
2. Introduction of the battery
There are three positions on the battery lock.
“ON”: The bike is powered on, and the battery locks on the frame. The key
cannot be removed at this time. “OFF”: The bike is powered off, but the
battery is locked on the frame. The key can be removed at this time.
“UNLOCK”: You need to push the key in to turn to this position. The bike
is powered off, and the battery is not locked on the bike.
Fuse: There are two Fuses on the battery. Charging Fuse: 10A, Min. 60Vdc;
Discharging Fuse: 30A, Min. 60Vdc. (UL certified Fuse)
3. Battery Charging
Find the charging port on the battery (Figure. 5-4), connect the charger’s
plug to the battery charging port first, and then connect the other side plug
to the AC outlet (120V).The charger’s LED is the red color when charging, and
it will turn to green color when the battery is fully charged. It will take
6-8 hours to fully charge the battery. Remember to charge the battery before
the first ride fully.
Please Note : There is a small button on the battery, turn on the
battery, press and hold the small button, you can see the remaining capacity
of the battery (There is one red light + two green lights when fully charged)
(Figure. 5-5).
4. Battery storage outside of the eBike
If the battery is not used for an extended period, charge it fully and
recharge it every two months.Store it in a cool, dry place.
Folding or Unfolding The bike
1. Locate the quick-release lever on the frame, open the lever (Figure 6-1), then pull it out. Hold the handle, and lift the pin up (Figure 6-2), then the frame can be folded now.
2. Open the handle on the frame. There is a small spherical handle on the side of the handle, pull it to the top, then pull the handle outward (Figure 6-3), fold the stem and pedals(Push the pedals in, and then flip them up). The bike is folded (Figure 6-4).
Operating Instructions
1. Lighting Up The Display
Turn the key to the “ON” position, press the “ON/OFF” button on display
(Figure. 7-1), and the display will be light up. Note: The default pedal
assist level is “LOW” (Figure. 7-2).
2. Testing The Throttle,Pedal Assist, And Walk Assist Mode
The bike has three modes: throttle, pedal-assist, and walk-assist. Please lift
the rear wheel, then test them separately.
A. Throttle: please twist the throttle. It is on the right side of the
handlebar(Figure. 7-3).
B. Pedal Assist: please lift the rear wheel and turn the pedal by hand. The
motor will work one time once you turn the crank 3/4-cycle (Figure. 7-4).
C. Walk assist: Please press and hold the “6km” button on the handlebar. The
bike will go into a walk-assist mode (Figure. 7-5).
3. Testing The Brake System
Please hold the 2 brake levers on both sides of the handle bar, then trying to
push the bike forward to make sure the bike is assembled firmly, and brakes
can stop the bike properly.
4. Please record the bike’s serial number (Figure. 7-6) and battery serial
number (Figure. 7-7) on the last page of the user manual in case of stolen or
missing.
5. You are ready to ride!
Display Instrument Setting
810 LED Display
ON/OFF: Turn on the power, press the “ON/OFF” button, the power will be turned ON or OFF.
6KM: Walk Assist Mode, press and hold the “6km/h” button to have cruise 6km/h speed automatic riding without pedals.
Mode: Press the “mode” button to select the pedal assistant power with pedals and throttle (Low-Med-High).
Power: Power is indicating the battery power. It should be four red LED when fully charged.
Troubleshooting
We fully understand your feelings when you meet a problem with the bike.
Contacting us on the website where you bought the bike and telling us your
problem in detail with some pictures and videos will be the fastest and
easiest way to help you solve the problem. Please don’t forget to leave your
order number to us for reference.
The following are some assist tips for electrical problems:
The display can not light up
Please fully charge the battery (6-8 hours). The LED on the charger should be
green color when the battery is full charged.
If it still doesn’t work, please check the wires and battery, please make sure
the connections are not loose, and the battery installs in place, then please
light up the display in the correct order (light up the power button on the
battery,press the “6km” button, and hold).
If it still doesn’t work, we need to get a voltmeter, and do some testing:
First,please light up the power button, and test the battery output voltage
(Figure. 8-1). If the voltage is “0”, it means there is something wrong with
the battery output plug, cell, or fuse. Please take a picture or a video to
show your testing result, and then send it to us. The customer service
department will give you a solution. If the battery voltage is not “0”, but
less than 32V, please full charge the battery (6-8 hours), then test it again;
if the battery voltage is between 32v-42v, but the display can not be light
up, it means the battery is in good condition, we need to test the other two
plugs.
Second, please open the controller box, and find the power wire (black and red
color) that connecting the battery and controller (Figure. 8-2). Please test
the power wire’s voltage. If it is “0”, it means the power wire needs to
replace, please take pictures, and send the pics to us. If the voltage is the
same as the battery, there’s no problem with the power wire. We need to test
the output voltage of the controller. It is the plug that connects the
controller and display. It has five wires on the plug, please test the red and
black wires (Figure. 8-3). If the voltage is “0”, it means the controller
needs to be replaced, please take some pictures and send them to us; if the
voltage is the same as the battery, it means the display needs to be replaced.
Please picture the testing results and send them to us. It will help us for
solving your problem asap.
We have video on YouTube, the model is different,but the method is the
same:
https://www.youtube.com/watch?v=zzrkBPsYjrg&t=1s
The throttle does not work
We mean the display can be lighted up, but the throttle does not work. The
brakes have two functions when you press the brake lever: 1. it will stop the
bike 2. it will cut the power of the motor.
First , please check the brake lever, and make sure the brake lever can
hold or release fluently. If not, maybe the brake cut the power. Please video
your problem and send it to us. We will give you a solution.
Second , Please test the pedal assist mode (please lift the rear wheel,
then turn the crank a whole cycle), and walk assist mode(press and hold the
“down” button). If only the throttle does not work, it means the throttle
needs to be replaced. Please video your testing and send the video to us. If
none of the three modes works, we need to test the motor wire and brake
sensor.
Third , please find the plug on the motor wire (Figure. 9-1), the
connection may loose. Please re-plug it, restart the bike, and then test all
three modes, if it still doesn’t work, we need to check the brake sensor.
Fourth , please open the controller box (Figure. 9-2), and find the two
plugs that connect the brake levers and controller. It is the only two plugs
that have two wires on each plug (Figure. 9-3). Please disconnect them , then
test all three modes again. If they work, it means the brake sensor is
defective. The brake wires need to be replaced. If it still doesn’t work, it
means the controller needs to be replaced. Please video your problem, and send
the video to us.
If it still doesn’t work after replacing the brake wire or controller, please
video how you do the troubleshooting, and send the video to us.
We have a video on YouTube,the model is different,but the method is the
same:
https://youtu.be/i_s9v7mw_zs
Warranty Information
The warranty covers items that fail when used within their normal operating
parameters. Please provide the order number when you need warranty. This
warranty applies only to the original registered owner of the ECOTRIC bicycle
and is not transferable.
TO ACTIVATE YOUR NEW ECOTRIC ELECTRIC BICYCLE WARRANTY, PLEASE REGISTER YOUR
BIKE BY THIS LINK. https://www.ecotric.com/pages/warranty-registration-1
If any part happen to be damaged during shipping, please contact us
immediately after shipment arrival. ECOTRIC will send a replacement part at
our expense and will work with you to fix the issue.
Situations that are not covered by warranty
- Water Damage (wading in the water, parking in the rain)
- Refit (refit the motor, electrical system, battery, frame, fork, etc. without our authorization)
- Overloading (Riding on steep slope/load more than 200lbs)
- Artificial damage (incorrect installation/usages)
- Uncontrollable factors (Crash, falling, stolen, etc.)
- Improper use (Abusive use the bicycle in off-road terrain, mud, water, gravel or jumping from ramps, stairs or elevated ramps,or using the bike at an altitude higher than 6562 feet )
- Damages caused by natural disasters (such as earthquakes, lightning, fire, flooding and other hazards).
- Use of other components (such as charger, battery, display, or controller, it may result in fire or death)
- Acts in violation of laws
- Never registered your ebike or cannot provide the order number
18 months Limited Warranty Components (In the period of 18 months from purchase by Official Authorized Store)
- Frame - are warranted to be free from defects in material or workmanship for 18 months from purchase by Official Authorized Store. Paint finish is considered consumable and is not part of the warranty.
- Motor, Display, Controller and Motor Assembly – are warranted to be free from defects in material or workmanship for a period of 18 months from purchase by Official Authorized Store.
- Original Battery – are warranted to be free from defects in material or workmanship for a period of 18 months from the date of purchase as follows: full replacement during the first 12 months, while replacements needed during months 13-18 are prorated by the below link https://www.ecotric.com/pages/battery-replacement-cost
Exclusions:
The warranty does not cover components subject to wear: Tires, inner tubes,
brake lines, brake pads, wheel lining tape, fuses, etc. The other parts are
Normal wear parts which are excluded from this warranty.
Please note that for warranty issues, the customer is responsible for the cost of labor to install warrantied components.
Return Policy
-
ECOTRIC Electric Bicycle Return Policy allows you to return or exchange your electric bicycle once within 30 days start from the date of receiving the bike. Please check the warranty terms for complete information for when a return is applicable. Please note that we do not accept the return of the spare parts. If you insist on returning it, you need to bear a 50% restocking fee of the original price.
-
Ship-back charge:
A. If the unit purchase under a free-shipping promotion, there will not be a refund for shipping cost. However, the customer will have to bear the 20% restocking fee of the original price if the return is unrelated to quality, damages, or wrong item but merely for a personal and discretional last-minute decision from the buyer.
B. If you need the pick-up service, please tell us, and we will arrange a return label with the pick-up fee for you, but the customer will need to pay for this pick-up fee.) -
The returned unit must be in like-new condition, include all original packaging, accessories, and documentation. Any missing components may be deducted from the refund. Any shipping damage during the ship-back may incur a deduction from the refund.
-
Returned units are subject to a 20% of inspection and restocking fee from the original purchase price.
-
The refund will be issued in an average time frame of 2-3 weeks after we are receiving, inspecting, and processing the returned unit.
-
If the customer wants to cancel the order after the shipping label being created, the customer will have to bear the shipping cost.
Please note : Buyer is required to get the packing box, pack the bike,
and take the bike to UPS/FedEx Store when the buyer wants to return the bike.
(Please keep the original box in case of returning if necessary). We cannot
accept your return request if you bought the bike for more than 30 days, but
we will keep providing our best customer service.
If the buyer picks up the bike locally, the buyer is responsible for carrying
the bike back to our warehouse.
If you buy the bike in the USA, but use it in the other country or Hawaii,
Alaska, or Puerto Rico, PO Boxes/APO’s is out of our delivery range. The buyer
is responsible for returning the bike to the original shipping address.
FAQ
Q: How does after-sale customer service/ warranty work?
A: When you have problems with your bike, please message us on the
website where you bought the bike. We will reply to you in one business day.
It is best to describe your problem in details, and make a video to show your
concern, it is the fastest way to solving your problem.
Example: My bike does not work. The customer should tell us that the display
can be lighted up, but the throttle does not work. When you have electrical
problems, the first thing we want to know is the display can be lighted up or
not, (The condition of the display will help us to distinguish how to solve
the electrical problems), then please provide more details about how it
happens and the symptom of the problem. We will report your problem/video to
our technician team, and give you a solution. If your bike is under warranty,
we will arrange spare parts from our warehouse in the USA.
Q: I’m tech inclined and think I can fix it myself,does that void the
warranty if I do?
A: No, we always like to work with and support customers who are
resourceful enough to fix an issue on their own, and we will provide plenty of
tech support over email to guide you through the process. It saves wasted time
and expense in shipping and it can be a useful and fun learning process.
Please contact us before attempting a DIY repair, however, as some things have
non-obvious complications.
Q: Why is the charger hot?
A: When the battery is charging, it is normal that the charger is getting
hot, because part of the energy is converted into heat energy when converting
AC to DC. As long as there’s no smell, you don’t need to worry about it.
However, it’s better to put it in a ventilated place, because the heat will
accelerate the aging of electronic components.
Q: What is the range of this bike?
A: We try to give an exact number, but the range is related to the road
conditions, rider’s weight, wind resistance, ramp or not, and how you ride the
bike. We test the bike on the city road, (slight wind, flat highway, rider
160lbs, throttle, and pedal assist), the range is 20 miles. Suppose you can
ride 16-23 miles. It is normal. Full charging the bike, and pump up the tire
full will Increase range.
Q: Can I ride the bike in the rain?
A: Yes, ride the rain in moderate or light rain is no problem. Please
make sure the bike is bone dry before next riding, or the bike will cut-off
randomly. But do not park the bike in rain and never wading in water. The
battery and controller have a self-protection program, they will cut the power
if there is a short, but water damage will destroy the the bike’s electrics.
Q: What is the most important thing for maintaining battery?
A: Remember to charge the bike in time, and not leave the bike with an
empty battery. Remember to charge the battery every 2 months if you do not use
it for a long time, or the battery will starve to death as no power. It will
result in a short-range or display can not light up.
Q: Do you have spare keys for the E-bike?
A: Sorry, we do not have spare keys, but spare lock-set. You should
replace the whole lock set if you lost the keys. Remember to keep a copy of
the key if necessary.
Battery And Charger Care
The charger will charge a fully depleted battery in 6–8 hours. The indicator light on the charger will be red when the battery is charging and will turn green when fully charged.
Avoid subjecting the battery to high temperatures, such as directly under the sun, for prolonged periods.
Recharge the battery before it becomes completely discharged. Completely discharging will reduce the numbers of recharging cycles during the battery’s life and limit the capacity. Never store the battery in a discharged state. After much use, your battery’s charge-holding capacity will decrease. If you find that your battery does not hold a sufficient charge, you should contact us to order a replacement.
If the battery is not used for an extended period, charge it fully and recharge it every two months. Store it in a cool, dry place. Your battery is engineered with precision for high capacity and a long, useful life. Please do not use it to power other electrical devices. Improper use of the battery will damage the battery and shorten its useful life and may cause fire or an explosion. If you experience unusual sounds or odors coming from the charger or the battery, unplug the charger immediately and contact customer service.
Recharge the battery after every use.
- Do not disassemble or alter the battery or battery charger.
- Do not place the battery near fire or corrosive substances.
- Do not allow any liquids on or inside the battery/charger.
- Do not expose the battery/charger to extreme weather conditions.
- Do not operate the battery/charger if damaged.
- Recharge the battery only with a charger specified by the manufacturer.
- Do not use the battery/charger for any use other than its intended purpose.
- Only use the battery/charger on approved products.
Please instruct your children to keep away from the charging place.
WARNING
RISK OF FIRE
NO USER SERVICEABLE PARTS
USER MAINTENANCE INSTRUCTIONS
Having an electric bike that breaks down or isn’t running smoothly is a real pain. Here are few simple things you can do to avoid this and keep it running smoother for longer.
Electric bikes are bicycles that have additional technology to provide pedal assistance. Because they tend to get used so much more, and at greater average speeds, maintenance is a critical factor in keeping them running smoothly.
You don’t need to have a fancy workshop, do these few simple things:
Bicycle maintenance
Regularly check the significant touch point bolts for tightness handlebars,
seat rails, wheels etc. If any of these come off while riding,it can be
dangerous! Riding with loose bolts can be an expensive and inconvenient
repair.
Lube your chain regularly.
Check tire pressures at least once a week. Pump up to the recommended pressures if needed.
Clean your ebike with a regular hose and / or bucket & brush. Avoid high pressure water systems as you don’t want to get water in the electrics!
Wiring. Be careful not to knock your wiring, particularly on things such as lights, motor cables near wheels, sensor cables etc.
Batteries. See our article on battery care and safety. Also, take care of sliding your battery in and out, so you don’t bend any battery plate nodes.
The next best thing you can do for your ebike is to get it serviced regularly by a skilled mechanic preferably one with experience working on electric bikes! Find or avoid problems before they happen.
MOVING AND STORAGE INSTRUCTIONS
There is very little to do in terms of electrics maintenance however the main
thing is to take care! Particularly when you are moving your ebike in and out
of cars, stairs or tricky storage places.
Prolonged Exposure to UV Rays, Rain and the Elements May Damage the Enclosure
Materials, Store Indoors When Not in Use.
Safety
Helmet:
Always wear an approved helmet while riding your bike and follow the helmet
manufacturer’s instructions for it, use and care of your helmet.
It is your responsibility to familiarize yourself with the laws of where you
ride your Bike and comply with all applicable laws.
Mechanical Safety Check:
Check the condition of your Bike before every ride. Make sure no nuts, bolts
or fixing are loose, with particular attention to the axle nuts and handlebar
stem. Make sure the tires are correctly inflated with the recommended air
pressure that locates on the side wall of every tire. Check the brakes for
proper operation. You must take your bike in to be serviced and checked by a
qualified bike mechanic before 100 miles (161 kilometers) of riding. This is a
standard good practice for any new bike as cables will stretch, and components
will “bed in”. The service must include spokes tension for both front and rear
wheels.
Your First Ride:
When you buckle on your helmet and go for your first ride, be sure to pick an
area away from cars, other cyclists, obstacles, or other hazards to become
familiar with the controls, features, and performance of your new Bike.
Additional Passengers:
The Bike bikes are designed for one passenger only (excluding Tandems). DO NOT
carry any additional passengers on the front or rear of the bike.
Weight Capacity:
These Electric Bikes are designed with a maximum weight capacity of 200 pounds
for all models. The rear rack maximum weight capacity of a Bike (if
applicable) is 25 pounds. Exceeding the maximum weight capacity can result in
damage of the bike, which can lead to serious injury.
Tires & Wheels
Make sure tires are correctly inflated. Check by putting one hand on the
saddle, one on the intersection of the handlebars and stem, then bouncing your
weight on the bike while looking at tire deflection. Compare what you see with
how it looks when you know the tires are correctly inflated; and adjust if
necessary. Tires in good shape? Spin each wheel slowly and look for cuts in
the tread and sidewall. Replace damaged tires before riding the bike. Are
wheels true? Spin each wheel and check for brake clearance and side-to-side
wobble. If a wheel wobbles side to side even slightly, or rubs against or hits
the brake pads, take the bike to a qualified bike shop to have the wheel
trued.
General Warning
Like any sport, bicycling involves the risk of injury and damage. By choosing
to ride a bicycle, you assume the responsibility for that risk, so you need to
know – and practice – the rules of safe and responsible riding and proper use
and maintenance. Proper usage and maintenance of your bicycle reduces the risk
of injury.
Your electric bicycle is designed for use by persons 16 years old or older.
Riders must have the physical coordination, reaction time and mental
capability to ride and manage traffic, road conditions,sudden situations and
respect the laws governing bicycle use where they ride, regardless of age. If
you have an impairment or disability such as a visual impairment, hearing
impairment, physical impairment, cognitive/language impairment, or a seizure
disorder, consult your physician before riding any bicycle.
A special note for parents
As a parent or guardian, you are responsible for the activities and safety of
your child, and that includes making sure that the bicycle is properly fitted
to the child; that it is in good repair and safe operating condition; that you
and your child have learned and understand the safe operation of the bicycle;
and that you and your child have learned, understand and obey not only the
applicable local motor vehicle, bicycle and traffic laws, but also the common
sense rules of safe and responsible bicycling. As a parent, you should read
this manual,and review its warnings and the bicycle’s functions and operating
procedures with your child, before letting your child ride the bike.
WARNING
Make sure that your child always wears an approved bicycle helmet when riding;
but also make sure that your child understands that a bicycle helmet is for
bicycling only, and must remove when not riding. A helmet must not be worn
while playing, in play areas, on playground equipment, while climbing trees,
or while not riding a bicycle. Failure to follow this warning could result in
serious injury or death.
Your electric bicycle is for use by persons 16 years old and older ONLY. Do
not let a child younger than 16 years old ride the bike.
Electrical Parameters
Model
| C-STA20LED-BL-XXX
C-STA20LED-W-XXX
C-STA20LED-MB-XXX
(XXX represents any alphanumeric character)
---|---
Motor|
36V 350W
Type of Motor
| Brush-less Hub motor
Battery|
36V12.5AH
Type of Battery
| Li-ion Battery
Charging Temperature Range|
32-104 °F
Discharge Temperature Range
| 14-113 °F
Charger Output|
42V DC MAX. 2.0A
Range Per Charging
| 18-23 miles
Maximum Speed|
20 MPH
Maximum Loading
| 200 LBS
Dimensions|
60.9×44.88×24.4 inch
Folding Dimensions
| 33.4x15x27.2 inch
Weight|
50 LBS
Maximum Elevation
| 6562 feet
Storage Temperature Range|
14-113 °F
The Universal Wiring Diagram
This wiring diagram is only for reference, if any question you have, please contact customer service for any repair.
colour
| black| red| purple| blue| orange| green| yellow| pink| white|
---|---|---|---|---|---|---|---|---|---|---
Code| B| R| P| U| O| G| Y| K|
W
Recording Your ECOTRIC Bike Info
BICYCLE SERIAL NUMBER:
BATTERY SERIAL NUMBER:
MODEL:____
COLOR:____
DATE OF PURCHASE:
DEALER’S NAME:____
DEALER’S PHONE:___
DEALER’S EMAIL:____
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>