V-TAC VT-5129 WiFi Receiver Instruction Manual

VT-5129 WiFi Receiver
WEEE Number: 80133970
Instruction Manual

INSTALLATION INSTRUCTION

WIFI RECEIVER

INTRODUCTION & WARRANTY

Thank you for selecting and buying V-TAC products. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any other queries, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at their best. The warranty is valid for 2 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. This product is warranted for manufacturing defects only.
*Note: The product depicted in this manual may appear slightly different from what you receive in the box

INTRODUCTION

Based on radio frequency (RF) and energy harvesting technology, the wireless switch does not need an external power supply to control. When pressing the button, the mechanical energy automatically converts into electrical energy. Meanwhile, the switch will send out radio signals to control the receiver on/off.
WARNING

1. Please switch off the power before starting the installation.
2. Installation must be performed by a cerfied electrician/person.

This marking indicates that this product should not be disposed of with other household wastes.
Caution, risk of electric shock.

RECEIVER INSTALLATION

Please follow the below installation diagram to install the receiver.

NOTES
A. The integrated load of the wireless receiver is 1000W.
Lamps can be LED lights, incandescent bulbs, exhaust fans, or WIFI devices, etc.

B. A one-gang wireless switch controls a wireless receiver

C. A two-gang wireless switch controls 2 wireless receivers

APPLICATION (HOME, HOTEL,INN OR FACTORY ETC.)
D. A receiver can be controlled by 8pcs of wireless switch panels at the most.
E. Three two-gang wireless switch controls 3 wireless receivers

F. A three-gang wireless switch controls 3 wireless receivers
G. A hand remote control switch controls 3 wireless receivers.

CODE OPERATION

PAIRING THE SWITCH & THE RECEIVER

1. Connect the receiver between the light and the power source.
2. Power on electricity, and press and hold the song button for 2 seconds. When the indicator light flashes, it enters the matching code mode, then loosen your finger.
3. Press the wireless switch button that you want to pair. Use the wireless switch to control the light on or off, indicating that the learning code is successful.

NOTE:
(a) Not recommended that 1 switch controls many receivers.
(b) Ensure that there is no other pairing within 100 meters range to avoid interface.

ADDING ANOTHER SWITCH TO A PAIRED SWITCH
Press and hold paired switch panel for about 20ll LED indicator on the switch blinks rapidly, then loosen your finger, press the new one, and finally test whether it can turn on/off the lamps.
DELETING AN ADDITIONAL SWITCH FROM A PAIRED SWITCH
Press and hold paired switch panel for about 60s, during which the LED indicator on the switch changes from: firstly blinks rapidly; secondly blinks 8 mes slowly, thirdly blinks 9 mes at a slower speed, finally blinks once at the slowest speed, then loosen

UNPAIRING THE RECEIVER
Press and hold the receiver button for about 10s, and loosen your finger when the indicator light changes from rapid blinks to slower, press the paired switch panel cannot control the lamps

HOW TO SET THE OPEN/CLOSE STATE OF THE RECEIVER TO MAKE THE WIRELESS SWITCH COMPATIBLE WITH THE TRADITIONAL SWITCH
Note: The receiver defaults to the Close state.

1. Power off the electricity, install the receiver as in the diagram, and distinguish live from neutral lines.
2. Power on the electricity, then program the receiver with the switch according to the Learning code Operation chapter

IF THE RECEIVER IS IN AN OPEN STATE,

• Turn on the traditional switch to light the lamps, the wireless switch can control the lamps.
• Turn off the traditional switch to light the lamps, the wireless switch cannot control the lamps.

METHOD OF SETTING THE RECEIVER IN AN OPEN STATE
Press and hold the switch button for 16s, and loosen your finger when the indicator light is continuously bright. (During the 16s, the indicator light will change from quick flash to slower flash, after that, the indicator light will be off, then will be on.)
METHOD OF SETTING THE RECEIVER IN A CLOSE STATE
Press and hold the switch button for 16s, and loosen your finger when the indicator light is continuously bright.
REPLACE THE BATTERY

1. Remove the switch frame and panel with a hand or screwdriver.
2. Remove 4 screws with a screwdriver, take off the battery cover
3. Replace the old battery with the new one, pay anon to the positive and negative poles of the battery;
4. Install the panel and frame again.

WIRELESS SWITCH INSTALLATION

The switch can be surface mounted with screws or double-sided stickers or set on the table.

1. Install with Double-sided adhesive. (Included)
   Pick up the area where you’re going to place the switch, clean the surface with a wet rag, post the adhesive rubber in the back of the switch, then attach the switch to the clean surface.

2. Install with screws (not included) First, take apart the frame and button panel of the switch, Fix the switch base on the wall with two screws, then install the parts together.

SPECIFICATIONS

PARAMETERS OF WIRELESS RECEIVER

PARAMETERS OF THE METAL HAND REMOTE

PARAMETERS OF THE WIRELESS SWITCH

Product Size| 868611MM
868613MM| Type| 1-gang, 2gang, 3-gang
---|---|---|---
Switch times| >600,000 times| Working frequency| 433.932 MHz +/-75KHz
Sensitivity| -116dB| Working voltage| 3V (CR2032)
Package weight| 82-86g| Life of the battery| >300,000 times
Emission current| <30 mA| Standby current| <0.01 uA
Working temperature| -40—+70°C| Waterproof| IP54
Working characteristics| No need wiring| Fireproof PC| CHIMEI
Remote distance| >600m outdoor| Light on the switch| Blue light
Remote distance| >40m indoor| Interchangeable panel| The three kinds of panels can be interchangeable

RECEIVER INSTALLATION

By Screws: Fit the receiver with KA3.5×25 screws in the applicable place.
By 3M tapes: Sck the double-sided tape on the plain surface of the receiver, then sck the receiver to the applicable place.
WARNING!

1. Please switch off the power before starting the installation.
2. Installation must be performed by a cerfied electrician/person.

Red, Blue input wires connect to AC220V to the AC110V power supply. Brown, Blue Output wires connect to lamps.

CODE LEARNING/PAIRING OR DELETE

I FIRST PAIRING

-> Keep pressing the receiver key for 2s
-> LED light is flashing, loosen the receiver key and enter the learning mode.
-> Press the remote key which you want to learn code.
-> Lamp turns on. Pairing is successful.
II ADD MORE KEYS

-> Press and hold paired remote key for about 20s LED indicator on the switch blinks rapidly, then loosen your grip, and press the new one once. Finally, test whether it can turn on/off the lamps.
III DELETE KEYS

-> Press and hold paired remote key for about 60s, during remote LED indicator on remote changes from:
Firstly blinks rapidly; Secondly, blink 8 mes slowly, Thirdly blink 9 mes at a slower speed, Finally blink once at the slowest speed, then loosen your grip, press the remote key again to check if the keys have been deleted or not.

IN CASE OF ANY QUERY/ISSUE WITH THE PRODUCT, PLEASE REACH OUT TO US AT:SUPPORT@V-TAC.EU
FOR MORE PRODUCTS RANGE, INQUIRY PLEASE CONTACT OUR DISTRIBUTOR OR NEAREST
DEALERS. V-TAC EUROPE LTD. BULGARIA, PLOVDIV 4000, BUL.L.KARAVELOW 9B

Documents / Resources

| V-TAC VT-5129 WiFi Receiver [pdf] Instruction Manual
VT-5129 WiFi Receiver, VT-5129 Receiver, VT-5129, Receiver, WiFi Receiver
---|---

References

• TAC.EU

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>