HUMMINBIRD 532365-4 Helix Series In-Dash Mounting Installation Guide

HELIX® SERIES IN-DASH MOUNTING
Installation Guide

Installation Overview

Following are instructions for the in-dash mount installation of the HELIX 7 control head. We encourage you to read this guide before starting the installation, so you may understand the installation requirements.
Technical Support: If you find that any items are missing from your installation kit, visit our Web site at humminbird.com or call Humminbird® Technical Support at 1-800-633-1468.
Supplies: In addition to the hardware supplied with your accessory, you will need the gimbal knobs (2) included with your control head, a drill and various drill bits, a cutting tool for the dashboard material, a 3/8″ wrench, a 5/16″ socket wrench, safety glasses, and dust mask, and masking tape.

WARNING! Do NOT use power tools to secure the hardware. We encourage you to read the installation instructions so you may understand the installation requirements.
NOTE: The illustrations in this manual may not look the same as your product, but your product will function in the same way.

Plan the Mounting Location

Start by locating a suitable, flat area of the dashboard for mounting. Consider the following to find the best mounting location:

• Interference: The mounting location must provide an adequate distance from electric motors or any equipment that may cause electronic interference.
• Stability: The mounting area should be protected from waves, shock, vibration, and water.
• Depth: The mounting area should have a depth of 3 inches (7.62 cm) to allow space for the control head and cables.
• Ventilation: The area beneath the mounting surface should be well-ventilated.
• Accessibility: The location should be easily accessible for all cables to reach the ports on the back of the control head.

NOTE: If a cable is too short for your application, extension cables are available. For assistance, contact Humminbird Technical Support at humminbird.com or call 1-800-633-1468.

HELIX 7 Series In-Dash Mounting Dimensions

Cut the In-Dash Mounting Hole

To in-dash mount, the HELIX control head, start by placing the components on the surfaces where you intend to install them.

1. Review the instructions, measurements, and cutting options indicated on the In-dash Mounting Template.

2. Tape the template to the chosen in-dash mounting location.

3. Using the template, select the cutting method that is best for your boat:
   Δ Drill one entry hole away from the main cut line that is large enough to insert the blade of your cutting tool.
   OR
   Δ Drill a corner hole away from the main cut line using a drill bit that will create a hole as close to a diameter of .5 inches (12.7 mm) as possible. Repeat for the other three corners as indicated on the template. Use one of the corner holes as an entry hole, or drill an additional entry hole away from the main cut line.

4. Carefully begin cutting toward the dotted cut line, and continue cutting to the inside of the line around the template.

5. Test the Mounting Hole: Install the control head in the mounting hole to test the fit. Make adjustments to the mounting hole as needed. Remove the template when finished.

6. Thoroughly clean and deburr the mounting hole.

Install the In-Dash Mount Bracket

To install the in-dash mount bracket, you will need the gimbal knobs included with your control head. See your control head installation guide for more details.

Preparation

1. Place the control head, with the screen facing down, on a towel or cloth on a stable and level surface.

Install the Ratchets

1. Hold the in-dash mount bracket so the arms on the bracket are pointing up.
2. On the inside of the ratchet, locate the ribs (two semicircles) and align them with the openings on the inside of the bracket arm (see the illustration Installing the Ratchets on the In-Dash Mount Bracket ). With this orientation, install the ratchet on the bracket arm.
3. Repeat: Repeat step 2 to install the second ratchet.

Installing the Rachets on the In-Dash Mount Bracket Install the Gimbal Knobs

1. Holding the ratchets in place, lower the bracket (with the bracket arms pointing down) onto the back of the control head. Align the ratchets on the bracket arms with the openings on the sides of the control head.
   NOTE: The in-dash mount bracket is symmetrical. Therefore, it does not require a specific installation orientation.

2. Confirm the bracket is parallel with the face of the control head (see the illustration Installing the In-Dash Mount Bracket on the Control Head ). Thread a gimbal knob into the opening on the control head and tighten using four to five rotations.

3. Repeat: Repeat step 2 to install the second gimbal knob.

4. Confirm the bracket is still parallel to the face of the control head and hand-tighten both gimbal knobs to secure the bracket to the control head.

Install the Bolts

1. Place the hardware onto each bolt in the following order: nut and washer. See the illustration Installing the In-Dash Mount Bracket on the Control Head.
2. Insert the bolts into the threaded bolt holes on the bracket. Hand-tighten the bolts until there is enough of the bolt exposed on the other side of the bracket to install the end cap. You will fully tighten the bolts in a later procedure.
3. Install one end cap on the end of each bolt.

Installing the In-Dash Mount Bracket on the Control Head

Install the Control Head

1. From the front of the dashboard, with the control head screen facing out, carefully lower the control head diagonally into the mounting hole. Insert one end of the bracket through the hole first.

2. Adjust the angle so the control head is centered in the mounting hole.

3. Press down lightly on the control head. Confirm the control head is seated flush against the dash. Make adjustments, as needed.

4. From under the dash, place the bracket reinforcement plate around the back of the control head.

5. Finger-tighten each bolt until the end cap is flush against the bracket reinforcement plate. Then, use a 5/16″ socket wrench to hand-tighten the bolts no more than 2 additional turns.
   Hand-tighten only!
   Do NOT over-tighten the bolts. There should be no play or gaps between the unit and the dash. The bracket should remain straight without bending.

6. Finger-tighten each nut until the nut and washer are flush against the bracket. Fully tighten each nut using a 3/8″ wrench while holding the bolt in place. Do NOT over-tighten the nuts. Hand-tighten only!
   

WARNING! Do NOT use power tools to secure the hardware.
WARNING! Do NOT over-tighten the bolts. If the bracket is bending or bowing, it is too tight. Over-tightening the bolts may damage the control head.

Route and Connect the Cables

1. See the installation guides included with each hardware component to install power and other optional equipment.
2. Route all cables (power, transducer, accessories) to the control head and insert the connectors into the correct ports on the back of the control head (see the illustration Connecting the Cables ).

Connecting the Cables

CAUTION! Do NOT mount the cables where the connectors could be submerged in water or flooded. If cables are installed in a splash-prone area, it may be helpful to apply dielectric grease to the inside of the connectors to prevent corrosion. Dielectric grease can be purchased separately from general hardware or automotive store.

Your control head is ready for on-the-water operation. See your control head operations manual for further details.

1-Year Limited Warranty

We warrant the original retail purchaser that products made by Humminbird have been manufactured free from defects in materials and workmanship. This warranty is effective for one year from the date of original retail purchase. Humminbird products found to be defective and covered by this warranty will be repaired or replaced free of charge at Humminbird’s option and returned to the customer freight prepaid. Humminbird’s sole responsibility under this warranty is limited to the repair or replacement of a product that has been deemed defective by Humminbird. Humminbird is not responsible for charges connected with the removal of such product or reinstallation of replaced or repaired parts, or shipping charges to the factory or authorized service center (if outside the U.S.).
This warranty does not apply to a product that has been:

• Improperly installed;
• Used in an installation other than that recommended in the product installation and operation instructions, including commercial applications;
• Damaged or has failed because of an accident or abnormal operation;
• Repaired or modified by entities other than Humminbird.

Please retain your original receipt as proof of the purchase date. This will be required for in-warranty service.

THIS WARRANTY IS EXPRESSLY IN LIEU OF ANY OTHER WARRANTIES, OBLIGATIONS, OR LIABILITIES ON THE PART OF HUMMINBIRD AND WILL BE THE CUSTOMER’S EXCLUSIVE REMEDY, EXCEPT FOR ANY APPLICABLE IMPLIED WARRANTIES UNDER STATE LAW WHICH ARE HEREBY  LIMITED IN DURATION TO ONE YEAR FROM THE DATE OF ORIGINAL PURCHASE. IN NO EVENT WILL HUMMINBIRD BE LIABLE FOR ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR BREACH OF ANY EXPRESS OR IMPLIED WARRANTY RELATING TO THE PRODUCTS.

Some states do not allow limitations on an implied warranty, or the exclusion of incidental or consequential damages, so the above exclusions may not apply to you. You may also have other rights, which vary from state to state.

Humminbird Service Policy

Even though you’ll probably never need to take advantage of our incredible service policy, it’s good to know that we back our products this confidently. We do it because you deserve the best. We will make every effort to repair your unit within three business days from the receipt of your unit at our factory. This does not include shipping time to and from our factory. Units received on Friday are typically shipped by the following Wednesday, units received Monday are typically shipped by Thursday, etc.

All repair work is performed by factory-trained technicians to meet exacting factory specifications. Factory-serviced units go through the same rigorous testing and quality control inspections as new production units.
After the original warranty period, a standard flat-rate service charge will be assessed for each repair (physical damage and missing parts are not included). Any repairs made after the original warranty will be warranted for an additional 90 days after service has been performed by our factory technicians. You can contact Technical Support or visit our Web site to verify the flat rate repair fee for your product (visit the Product Support section): http://www.humminbird.com

We reserve the right to deem any product unserviceable when replacement parts are no longer available or impossible to obtain. This Service Policy is valid in the United States only. This applies only to Humminbird products returned to our factory in Eufaula, Alabama. This Service Policy is subject to change without notice.

DOMESTIC (USA) CUSTOMERS:
PLEASE DO NOT RETURN THIS PRODUCT TO THE STORE FOR SERVICE
For all technical issues please call 1-800-633-1468
or visit humminbird.com, click SUPPORT.
Please reference the product serial number and
model number when contacting Humminbird.

Returning Your Unit for Service

Before sending your unit in for repair, please contact the factory, either by phone or by email, to obtain a Repair Authorization Number for your unit.

NOTE: Please do not return your Humminbird to the store for service.

Please have your product model name and serial number available before calling the factory. If you contact the factory by e-mail, please include your product model name and serial number in the e-mail, and use the Request for Repair Authorization Number for your e-mail subject header. You should include your Repair Authorization Number in all subsequent communications about your unit.

For IN-WARRANTY service, complete the following steps:

• Obtain a Repair Authorization Number from Humminbird Technical Support.
• Tag the product with your name, street address, phone number, and your assigned Repair Authorization Number.
• Include a brief written description of the problem.
• Include a copy of your receipt (to show proof and date of purchase).
• Return product freight prepaid to Humminbird, using an insured carrier with delivery confirmation.

For OUT-OF-WARRANTY service, complete the following steps:

• Obtain a Repair Authorization Number from Humminbird Technical Support.
•  Include payment in the form of a credit card number and expiration date or money order. Please do not send cash.
• Tag the product with your name, street address, phone number, and your assigned Repair Authorization Number.
•  Include a brief written description of the problem.
•  Return product freight prepaid to Humminbird, using an insured carrier with delivery confirmation.

Contact Humminbird

Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA

WARNING! Disassembly and repair of this electronic unit should only be performed by authorized service personnel. Any modification of the serial number or attempt to repair the original equipment or accessories by unauthorized individuals will void the warranty.

NOTE: Product specifications and features are subject to change without notice.

ENVIRONMENTAL COMPLIANCE STATEMENT: It is the intention of Johnson Outdoors Marine Electronics, Inc. to be a responsible corporate citizen, operating in compliance with known and applicable environmental regulations, and a good neighbor in the communities where we make or sell our products.

WEEE DIRECTIVE: EU Directive 2002/96/EC “Waste of Electrical and Electronic Equipment Directive (WEEE)” impacts most distributors, sellers, and manufacturers of consumer electronics in the European Union. The WEEE Directive requires the producer of consumer electronics to take responsibility for the management of waste from their products to achieve environmentally responsible disposal during the product life cycle.

WEEE compliance may not be required in your location for electrical & electronic equipment (EEE), nor may it be required for EEE designed and intended as a fixed or temporary installation in transportation vehicles such as automobiles, aircraft, and boats. In some European Union member states, these vehicles are considered outside of the scope of the Directive, and EEE for those applications can be considered excluded from the WEEE Directive requirement.

This symbol (WEEE wheelie bin) on a product indicates the product must not be disposed of with other household refuse. It must be disposed of and collected for recycling and recovery of waste EEE. Johnson Outdoors Marine Electronics, Inc. will mark all EEE products in accordance with the WEEE Directive. It is our goal to comply with the collection, treatment, recovery, and environmentally sound disposal of those products; however, these requirements do vary within European Union member states. For more information about where you should dispose of your waste equipment for recycling and recovery and/ or your European Union member state requirements, please contact your dealer or distributor from which your product was purchased.

© 2021 Johnson Outdoors Marine Electronics, Inc. All rights reserved.
532365-4_A

Documents / Resources

| HUMMINBIRD 532365-4 Helix Series In-Dash Mounting [pdf] Installation Guide
532365-4 Helix Series In-Dash Mounting, 532365-4, Helix Series In-Dash Mounting
---|---

References

• humminbird.com
• humminbird.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>