thermaltake TF1 1550W Toughpower Installation Guide
- June 7, 2024
- thermaltake
Table of Contents
thermaltake TF1 1550W Toughpower
Warnings and Caution
- Do not unplug the AC power cord when the power supply is in use. Doing so may cause damage to your components.
- Do not place the power supply in a high humidity and/or temperature environment.
- High voltages exist in the power supply. Do not open the power supply case unless you are an authorized service technician or electrician. Doing so will void the warranty.
- The power supply should be powered by the source indicated on the rating label.
- Please use only genuine Thermaltake modular cables with Thermaltake Cable Management power supply models. Third party cables might not be compatible and could cause serious damage to your system and power supply. The warranty is voided with the use of third party cables.
- All warrantees and guarantees will be voided, if failure to comply with any of the warnings and cautions covered in this manual.
Components Check
- TOUGHPOWER TF1 power supply unit
- AC power cord
- User manual
- Mounting screws x 4
- Cable straps x 4
Power Connector Introduction
| | | | | |
---|---|---|---|---|---|---
Main Power Connector (24 Pin)
| CPU Connector (8 Pin / 4+4 Pin| SATA Connector (5 Pin)| PCI-E Connector (8
Pin / 6+2 Pin)| Peripheral Connector (4 Pin)| Extra jumper accessory| Floppy
Adapter (4 Pin)
1| 2| 16| 8| 8| 1|
1
Output Specification
Continuous Power
|
AC INPUT
| Input Voltage: 100V – 240V~ ;
Input Current: 18A max. ; Frequency: 47Hz – 63Hz
---|---|---
1550W
| DC OUTPUT| +3.3V| +5V| +12V| -12V|
+5VSB
Max Output Current| 22A| 22A| 129.16A| 0.5A| 3A
Max Output Power
| 120W| 1549.92W| 6W|
15W
Installation Steps
Note: Make sure that your system is turned off and unplugged.
Disconnect the AC power cord from your old power supply.
-
Open your computer chassis; please refer to the instruction manual provided with your chassis.
-
Install the PSU into the case with the four screws provided.
-
If your motherboard requires a 24pin Main Power connector, please connect the 24pin Main Power connector to the motherboard.
-
-1. For motherboard that only requires a 4pin ATX 12V (CPU) connector, please detach a 4pin c onnector from the 4+4pin ATX 12V connector and connect it to the motherboard. (Either one of the 4pin from the 4+4pin ATX 12V connector will work)
4-2. For motherboard that requires a single 8pin EPS connector, please use the 4+4pin connector from the power supply. -
Connect other peripheral power connectors to devices such as hard drives,optical drives,etc.
-
If your graphic card requires PCI-E power connector, please connect corresponding PCI-E connector instructed by your graphic card’s user manual. Please note the power supply utilizes an unique 6+2pin PCI-E connector that can be effectively used as a single 8pin or 6pin PCI-E connector. To use it as a 6pin PCI-E connector, please detach the 2pin connector from the 6+2pin connector.
-
Close your computer case and connect the AC power cord to the power supply AC inlet.
-
This PSU is equipped with a turbo mode button, press this button, the fan speed is the turbo mode.
Total Protection
– Over Voltage Protection
Voltage Source
| Protection Point
---|---
+3.3V|
3.7V~4.5V
+5V
| 5.5V~7.0V
+12V|
13.6V~15.6V
– Short Circuit Protection
Activated when any DC rails short circuited
– Under Voltage Protection
Voltage Source
| Protection Point
---|---
+3.3V|
2.55V~2.83V
+5V
| 4.1V~4.47V
+12V|
8.8V~9.8V
– Over Power Protection
The power supply shall be shut down and latch off, if the wattage of the power
supply is 120% ~ 145% over continuous power.
– Over Current Protection
Voltage Source
|
Protection Point
---|---
+3.3V
| 150%
+5V|
150%
+12V
| 145%
+12V(SATA)|
145%
– Over Temperature Protection
Protection temperature is 60 to 80 at 115V and full load.
EMI & SAFETY
EMI Regulatory & SAFETY Standards
TOUGHPOWER TF1 1550W| CE, cTUVus, TÜV, FCC, EAC, CCC, S-Mark and BSMI certified.
Environments
| Operating temperature | Q°C to +50°C |
|---|---|
| Operating humidity | 20% to 90%,non-condensing |
| MTBF | > 120,000 hours |
Trouble-Shooting
If the power supply fails to function properly, please follow the troubleshooting guide before application for service:
- Is the power cord plugged properly into electrical outlet and into the power supply AC inlet?
- Please make sure the I/O switch on the power supply is switched to I position.
- Please make sure all power connectors are properly connected to all the devices.
- If connected to a UPS unit, is the UPS on and plugged in?
If the power supply is still unable to function properly after following the above instruction, please contact your local store or Tt branch office for after sales service. You may also refer to Thermaltake’s website for more technical support: thermaltake.com
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>