KENWOOD Multipro Excel FPM910 Food Processor Instructions

Multipro Excel FPM910 Food Processor
Instruction Manual

|
---|---

safety

• Read these instructions carefully and retain them for future reference.

• Remove all packaging and any labels.

• The blades and discs are very sharp, handle with care. Always hold by the finger grip at the top, away from the cutting edge, both when handling and cleaning.

• Do not lift or carry the processor by the handle – or the handle may break resulting in injury.

• Always remove the knife blade before pouring contents from the bowl.

• Keep hands and utensils out of the processor bowl and blender goblet whilst connected to the power supply.

• Switch off and unplug:-

• before fitting or removing parts; when not in use; before cleaning.

• Never use your fingers to push food down the feed tube. Always use the pusher/s supplied.

• Never fit the blade unit to the power unit without the blender goblet or compact chopper/grinder fitted.

• Before removing the lid from the bowl or blender or compact chopper/grinder from the power unit:-switch off; wait until the attachment/blades have completely stopped;  be careful not to unscrew the blender goblet or compact chopper/grinder from the blade assembly.

• SCALD RISK: Hot ingredients should be allowed to cool to room temperature before blending.

• Do not use the lid to operate the processor, always use the on/off speed control.

• This appliance will be damaged and may cause injury if the interlock mechanism is subjected to excessive force.

• Always unplug your food processor when not in use.

• Never use an unauthorized attachment.

• Never leave the appliance unattended when it is operating.

• Never use a damaged appliance. Get it checked or repaired: see ‘service & customer care.

• Never let the power unit, cord, or plug get wet.

• Don’t let excess cord hang over the edge of a table or worktop or touch hot surfaces.

• Do not exceed the maximum capacities stated in the recommended speed chart.

• This appliance shall not be used by children. Keep the appliance and its cord out of reach of children.

• Children should be supervised to ensure that they do not play with the appliance.

• Appliances can be used by persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or  instruction concerning the use of the appliance in a safe way and if they understand the hazards involved.

• Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.

• Misuse of your processor/blender can result in injury.

• The maximum rating is based on the attachment that draws the greatest load. Other attachments may draw less power.
  Refer to the relevant section under “using the attachments” for additional safety warnings for each individual attachment. blender safety

• SCALD RISK: Hot ingredients should be allowed to cool to room temperature before blending.

• Always take care when handling the blade assembly and avoid touching the cutting edge of the blades when cleaning.

• Only operate the blender with the lid in place.

• Only use the goblet with the blade assembly supplied.

• Never run the blender empty.

• To ensure the long life of your blender, do not run it for longer than 60 seconds.

• Smoothie recipes – never blend frozen ingredients that have formed a solid mass during freezing, break it up before adding to the goblet.

• Important – The skirt on the base of the goblet is fitted during manufacture and no attempt should be made to remove it.

IMPORTANT: HOT BLENDING INSTRUCTIONS
To minimize the possibility of scalding when blending hot ingredients keep hands and other exposed skin away from the lid to prevent possible burns.
The following precautions must be observed:

• CAUTION: Blending very hot ingredients may result in hot liquid and steam being forced suddenly past the lid or filler cap bq.
• We recommend that hot ingredients are allowed to cool before blending.
• NEVER exceed 1200mls/5 cups capacity if processing hot liquids, such as soups (refer to the markings on the goblet).
• ALWAYS commence blending at a low speed and gradually increase the speed. NEVER blend hot liquids by using the Pulse setting.
• Liquids that tend to foam such as milk, should be limited to a maximum capacity of 1000mls/4 cups.
• Take care when handling the blender as the goblet and its contents will be very hot.
• Take particular care when removing the lid. The lid is designed to be a tight fit to prevent leakage. If necessary protect your hands with a cloth or oven gloves when handling.
• Ensure the goblet is securely attached to the base and when removing from the appliance, guide the base and ensure it is removed together with the goblet.
• Ensure that the lid and filler cap is securely in place before every blending operation.
• Always ensure that the vents in the filler cap are clear before every blending operation cl.
• When fitting the lid to the goblet always ensure that the lid and goblet rim is clean and dry to ensure a good seal and prevent spillage.

slicing/grating disc safety

• Never remove the lid until the cutting disc has completely stopped.
• Handle the cutting discs with care – they are extremely sharp.
• Do not overfill the bowl – do not exceed the maximum capacity level marked on the bowl.

compact chopper/grinder safety

• Never fit the blade unit to your food processor without the jar fitted.
• Never unscrew the jar while the compact chopper/grinder is fitted to your appliance.
• Do not touch the sharp blades – Keep the blade unit away from children.
• Never remove the compact chopper/grinder until the blades have completely stopped.
• To ensure the long life of your compact chopper/grinder, do not run it continuously for longer than 60 seconds. Switch off as soon as you have got the right consistency.
• The appliance will not work if the compact chopper/grinder is incorrectly fitted.
• Do not process turmeric root in the compact chopper/grinder as it is too hard and may damage the blades.

juice extractor safety

• Do not use the juice extractor if the filter is damaged.

• Only use the pusher supplied. Never put your fingers in the feed tube.
  Unplug before unblocking the feed tube.

• Before removing the lid, switch off and wait for the filter to stop.

before plugging in

• Make sure your electricity supply is the same as the one shown on the underside of your appliance.
• This appliance conforms to EC directive 2004/108/EC on Electromagnetic Compatibility and EC regulation no. 1935/2004 of 27/10/2004 on materials intended for contact with food.

before using it for the first time
1 Remove the plastic blade covers from the knife blade. Take care the blades are very sharp. These covers should be discarded as they are to protect the blade during manufacture and transit only.
2 Wash the parts see ‘care & cleaning’

key processor

weighing function (Type FPM91)

Thermoresist blender

A – standard attachments

B -Optional attachments

Not all the attachments listed below will be included with your food processor model. Attachments are dependent upon the model variant. For more information or to order additional attachments refer to the “service and customer care” section.

To use your food processor

1. Fit the detachable drive shaft onto the power unit 1 – push down lightly to ensure the drive shaft is fully engaged.

2. Then fit the bowl into the power unit. Place the handle towards the back on the right-hand side and turn clockwise 2 until it locks.

3. Fit an attachment over the bowl drive shaft.
   • Always fit the bowl and attachment onto the processor before adding ingredients.

4. Fit the lid 3 – ensuring the top of the drive shaft/tool locates in the center of the lid.

5. Fit the pushers to the feed tube – turn the small pusher clockwise to lock in position 4.
   • The processor will not operate if the bowl, lid, or wide feed tube pusher are not fitted correctly into the interlocks. Check that the feed tube and bowl handle are situated on the right-hand side.

6. Plugin. The Power On light will come on and flash until the bowl and lid are fitted correctly. Select one of the following options: Auto Button – the light will come on when the Auto Button is pressed and the optimum speed for the attachment will be automatically selected. Speed Control – manually select the required speed (refer to the recommended speed chart). Pulse – use the pulse (P) for short bursts. The pulse will operate for as long as the control is held in position.

7. At the end of processing turn the speed control to the ‘O’ off position or if using the Auto press the button and the light will go out.
   • The Power On light will flash if either the lid, bowl or wide feed tube are not fitted.
   • The Power On and Auto lights will flash if the Auto is selected but the interlocks are not engaged.
   • The Auto Button will not operate if a speed is selected on the speed control.
   • Always switch off and unplug before removing the lid. important
   • Your processor is not suitable for crushing or grinding coffee beans or converting granulated sugar to caster sugar.

Eco function

If the food processor is left plugged in for over 30 minutes without being used, it will go into standby mode to reduce energy consumption.

• The Power On light will pulse slowly and the food processor will not operate until one of the following actions are carried out:-
• The Auto Button is pressed.
• The speed control is turned to a speed and then turned back to the ‘O’ off position.

The light will change to being constantly lit when ready to use.
Note: If the bowl or lid is not engaged in the interlock the power on the light will pulse more rapidly than the Eco function.

weighing function (Type FPM91)

Your food processor is fitted with a built-in weighing function to allow ingredients to be weighed straight into the bowl or blender goblet.

• The maximum weighing capacity is 3Kg. This is the total weight of all the ingredients including the weight of the bowl or goblet.

to use the weighing function

1. Always fit the detachable drive shaft, bowl, and attachment or blender goblet onto the power unit before adding ingredients.

2. Plugin – the display screen will remain blank.

3. Press the ON/ZERO button once and the display screen will light up.

4. Press the (kg/lb) button to select either grams or ounces. The display will default to kg/g when first switched on.
   • The unit weighs in 2g increments and teaspoon/tablespoon measures are recommended for weighing small quantities.

5. Check the display shows ‘0’, if not, zero by pressing the ON/ZERO button. Then weigh the required ingredients straight into the bowl or goblet. After the weight is displayed, press the ON/ZERO button and the display will return to ‘0’.
   Add the next ingredients and that weight will be displayed.
   Repeat until all ingredients are weighed.
   • If the display is not zeroed and either the ingredients or the bowl/attachment/lid are removed the display will show [ – – -] to represent a minus reading.
   To zero press the ON/ZERO button once.

6. Add the lid and select a speed to operate the processor.
   • During operation the display screen will freeze [- – – -] until the speed control returned to the ‘O’ off position.
   • After processing the last weight will be displayed on the screen when the speed control is returned to the ‘O’ off position. Note: The weight of the lid will be included if  the display is not zeroed before switching on.
   • The weight of any additional ingredients added down the feed tube whilst the processor is running will not be shown on the display screen.

weighing tray

A removable weighing tray is supplied for weighing ingredients without the bowl or blender.
To use, place the tray on top of the power unit. Then follow steps 2 to 5 under ‘to use the weighing function’.
To remove, just lift the tray off.

auto switch off

• The display screen will turn off automatically if the same weight reading is shown after 5 minutes.

• The display screen can be turned off manually by pressing and holding down the ON/ZERO button for a few seconds.
  important

• Do not overload by exceeding the maximum weighing capacity of 3Kg. The display will show [0 – Ld] if the weighing function is overloaded.

• Do not subject the power unit to excessive force as this may damage the weighing sensor.

• Always place the processor on a dry flat surface prior to weighing.

• Do not move the power unit during the operation of the weighing function.

to use your Thermo resist blender

1. Fit the sealing ring bt into the blade unit CK – ensuring the seal is located correctly in the grooved area.
   • Leaking will occur if the seal is damaged or incorrectly fitted.

2. Hold the underside of the blade unit CK and insert the blades into the goblet – turn anti-clockwise until it clicks 5. Refer to the graphics on the underside of the blade unit as follows:
   – unlocked position
   – locked position
   The blender will not work if incorrectly assembled.

3. Put your ingredients into the goblet.

4. Fit the lid to the goblet and push down to secure 6. Fit the filler cap.

5. Place the blender onto the power unit, and turn clockwise 7 to lock.
   • The appliance will not operate if the blender is incorrectly fitted to the interlock.

6. Select Auto, or a speed (refer to the recommended speed chart) or use the pulse control.

hints

• When making mayonnaise, put all the ingredients, except the oil, into the blender. Remove the filler cap. Then, with the appliance running, add the oil slowly through the hole in the lid.

• Thick mixtures, e.g. pâtés and dips, may need scraping down.
  If the mixture is difficult to process, add more liquid.

• Ice crushing – operate the pulse in short bursts until crushed to the desired consistency.

• The processing of spices is not recommended as they may damage the plastic parts.

• The appliance will not work if the blender is incorrectly fitted.

• To blend dry ingredients – cut into pieces, remove the filler cap, then with the appliance running, drop the pieces down one by one. Keep your hand over the opening. For best results empty regularly.

• Don’t use the blender as a storage container. Keep it empty before and after use.

• Never blend more than 1.6 liters (56 fl oz) – less for frothy liquids like milkshakes.

Recommended speed chart

tool/attachment| function| recommended
speed| processing
time | maximum capacities
---|---|---|---|---
Knife blade| All in one cake mixes| 8| 15-20 secs| 2Kg/41b 8oz flour weight
Pastry – rubbing fat into flour
Adding water to combine pastry ingredients| 5 – 8| 10 secs
10-20 secs| 500g/1 lb 2oz flour weight
Chopping fish and lean meat Patés and terrines| Pulse – 8| 10-30 secs| 1Kg/2Ib 4oz max lean beef
Chopping vegetables| Pulse| 5-10 secs| 500W1lb 2oz
Chopping nuts| 8| 30-60 secs| 200g/8oz
Pureeing soft fruit, cooked fruit and vegetables| 8| 10-30 secs| 1Kg/2Ib 4oz
Sauces, dressing and dips| 8| 2 mins max| 800g/1 Ib 8oz
Knife blade with max capacity disc| Cold soups| Start at low speed and increase to maximum| 30-60 secs| 2 litres/4pts
Milkshakes/batters| 15-30 secs| 1.5 litres/2pts 12 fl oz
Dual whisk| Egg whites| 8| 60-90 secs| 2 – 8 (70g – 280g)
Egg & sugar for fatless sponges| 8| 4-5 min| 3 eggs (150g)
Cream| 8| 30 secs| 250 mIs – 750mIs 9 fl oz – 27 fl oz
Folding tool| Whipping cream and fruit purees| 1 – 2| 60 secs| 300g/12oz cream, 300g/12oz puree
Egg whites into heavy mixtures| 1 – 2| 60 secs| 6003y1lb 6oz total wt
Macaroons| 1 – 2| 60 secs| 500g/1 lb 2oz total wt
Dough tool| Yeasted mixes| 8| 60 secs| 1.3Kg/ 2Ib 12oz total wt
White Bread Flour| 8| 60 secs| 650g/1 Ib 8oz flour wt
Wholemeal Bread Flour| 8| 60 secs| 500g/1 Ib 2oz flour wt
Discs – slicing/grating| Firm food ftems such as carrots, hard cheeses| 5 – 8| –| Do not fill above
the maximum capacity
marked on the bowl
Softer ftems such as cucumbers, tomatoes| 1 – 5| –
Extra fine grater| Parmesan cheese, potatoes for German potato dumplings| 8| –
Fine Julienne disc| Potato straws and rosti
Stir fries aid vegetable garnishes| 8| –
Decorative slicing disc| Firm food items such as carrots and potatoes Softer food items such as cucumber| 5 – 8| –
French fry disc| Cuts potatoes for thin French Fries and ingredients for casseroles and dips
(eg cucumber, apple and pear.)| 8| –
Thermoresist blender| Cold liquids and drinks| 8| 15-30 secs| 1.6 litres/56 fl oz
Stock based soups| 8| 30 secs| 1.2 litres/42 fl oz
Soups using milk| 8| 30 secs| 1 litres/2pts
We recommend that hot ingredients are allowed to cool before blending. However should you wish to process hot ingredients please read the Hot Blending Safety instructions.
Mini bowl and knife| Meat| 8| 20 secs + Pulse| 300g/12oz Lean beef
Chopping herbs| 8| 30 secs| 20g/1oz
Chopping nuts| 8| 30 secs| 100g/4oz
Mayonnaise| 8| 30 secs| 2 Eggs 300g/12oz Oil
Purees| 8| 30 secs| 200g/8oz
tool/attachment| function| recommended
speed| processing
time | maximum capacities
---|---|---|---|---
Compact chopper/ grinder| Processing a range of spices| 8| 30-60 secs| 100g/4oz
Grinding coffee beans| 8| 30 secs| 75g/3oz
Chopping nuts| Pulse| 5 secs| 140g/5oz
Lean braising steak (cut into 2cm cubes)| Pulse| 10 secs| 200g/8oz
Citrus Juicer| Smaller items i.e. limes and lemons| 1 – 2| –| 2Kg/4Ib 8oz
Larger fruits i.e. oranges and grapefruits
Juice extractor| Juicing firm fruit and vegetables ie apples and carrots| auto| –| 1Kg/2Ib 4oz apples 800g/1 lb 12oz carrots
Juicing soft fruits ie grapes and tomatoes| auto| –| 500g/1 lb 2oz

❋This is for guidance only and will vary depending on the exact recipe and ingredients being processed.

using the attachments
Refer to recommended speed chart for each attachment.

knife blade

The knife blade is the most versatile of all the attachments.
The length of the processing time will determine the texture achieved. For coarser textures use the pulse control.
Use the knife blade for cake and pastry making, chopping raw and cooked meat, vegetables, nuts, pâté, dips, pureeing soups, and to also make crumbs from biscuits and bread.

hints

• Cut food such as meat, bread, and vegetables into cubes approximately 2cm/3/4in before processing.
• Biscuits should be broken into pieces and added down the feed tube whilst the appliance is running.
• When making pastry use fat straight from the fridge and cut into 2cm/3/4in.cubes.
• Take care not to over-process.

Dough tool

Use for yeasted dough mixes.

• Place the dry ingredients in the bowl and add the liquid down the feed tube whilst the appliance is running. Process until a smooth elastic ball of dough is formed this will take approx. 60 secs.
• Re-knead by hand only. Re-kneading in the bowl is not recommended as it may cause the processor to become unstable.

Dual whisk

Use for light mixtures only e.g. egg whites, cream, evaporated milk and for whisking eggs and sugar for fatless sponges. Heavier mixtures such as fat and flour will damage it.

using the whisk

1. Fit the detachable drive shaft and bowl onto the power unit.
2. Push each beater 8 securely into the drive head.
3. Fit the whisk by carefully turning it until it drops over the driveshaft.
4. Add the ingredients.
5. Fit the lid – ensuring the end of the shaft locates in the center of the lid.
6. Switch on.

important

• The whisk is not suitable for making all in one ake mixes as these mixes are too heavy and will damage it. Always use the knife blade. hints
• Best results are obtained when the eggs are at room temperature.
• Ensure the bowl and whisks are clean and free from grease before whisking.
• Heavier ingredients such as flour and dried fruit should be folded in by hand.
• Do not exceed the maximum capacity or processing time stated in the recommended speed chart.

Folding tool

Use the folding tool to fold light ingredients into heavier mixtures for example meringues, mousses, and fruit fools.

1. Fit the detachable drive shaft and bowl onto the power unit.
2. Push the paddle 9 securely into the drive head.
3. Fit the folding tool by carefully turning it until it drops over the driveshaft.
4. Add the ingredients.
5. Fit the lid – ensuring the end of the shaft locates in the center of the lid.
6. Select low speed (speed 1 -2).
   to remove the beater
   Detach the beater from the drive head by pressing the release button bk.

hints

• Do not use Auto or high speed as a low speed is required to optimize the folding performance.
• For best results do not over whisk egg whites or cream –the folding tool will not be able to fold the mixture correctly if the whisked mix is too firm.
• Do not fold the mixture for longer than stated in the recommended speed chart as the air will be knocked out and the mix will be too loose.
• Any unmixed ingredients left on the paddle or sides of the bowl should be carefully folded using the spatula.

Max capacity disc

When blending liquids, use the max capacity disc with the knife blade. It allows you to increase the liquid processing capacity from 1.4 liters to 2 liters, prevents leaking, and improves the chopping performance of the blade.

1. Fit the detachable drive shaft and bowl onto the power unit.
2. Fit the knife blade.
3. Add ingredients to be processed.
4. Fit the capacity discover the top of the blade ensuring it sits on the ledge inside the bowl 11. Do not push down on the capacity disc.
5. Fit the lid and switch it on.

Slicing/grating discs

slicing discs – 4mm 27, 2mm 28
Use the slicing side for cheese, carrots, potatoes, cabbage, cucumber, courgette, beetroot, and onions.

grating discs – 4mm 29, 2mm 30
Use the grating side for cheese, carrots, potatoes, and foods of a similar texture.

extra fine grater disc 32 (if supplied)
Grates Parmesan cheese and potatoes for German potato dumplings.

fine julienne 33 (if supplied)
Use to cut potatoes into straws and coarse grate for rosti, stir-fries, and vegetable garnishes.

decorative slicing disc 34 (if supplied)
Use to slice potatoes, carrots, cucumbers, and foods of a similar texture into fluted-shaped slices.

French fry disc 35 (if supplied)
Cuts potatoes for thin French Fries and ingredients for casseroles and dips (eg cucumber, apple, and pear.)

safety

• Never remove the lid until the cutting disc has completely stopped.
• Handle the cutting discs with care – they are extremely sharp.
• Do not overfill the bowl – do not exceed the maximum capacity level marked on the bowl.

to use the cutting discs

1. Fit the detachable drive shaft and bowl onto the power unit..
2. Holding by the center grip, place the disc onto the drive shaft with the appropriate side uppermost bm.
3. Fit the lid.
4. Put the food in the feed tube.
   Choose which size feed tube you want to use. The pusher contains a smaller feed tube for processing individual items or thin food items.
   To use the small feed tube – first put the large pusher inside the feed tube.
   To use the wide feed tube – fit the small pusher into the wide pusher and turn clockwise to lock in place.
   Do not fill the feed tube above the maximum level as the processor will not operate unless the wide feed tube pusher is fitted correctly.
   5 Switch on and push down evenly with the pusher – never put your fingers in the feed tube. hints
   • Use fresh ingredients
   • Don’t cut food too small. Fill the width of the feed tube fairly full. This prevents the food from slipping sideways during processing. Alternatively use the small feed tube.
   • When using the Julienne disc, place ingredients horizontally.
   • When slicing or grating: food placed upright bn comes out shorter than food placed horizontally bo.
   • Food placed upright comes out shorter than food placed horizontally.
   • There will always be a small amount of waste on the disc or in the bowl after processing.

Mini bowl and knife (if supplied)

Use the mini processor bowl to chop herbs and process small quantities of ingredients e.g. meat, onion, nuts, mayonnaise, vegetables, purées, sauces, and baby food.
Do not overfill the bowl.

a mini blade
b mini bowl

to use the mini bowl and knife

1. Fit the detachable drive shaft and bowl onto the power unit.

2. Fit the mini bowl over the detachable drive shaft – ensure the cutout sections align with the locating tabs 15 on the main bowl.
   Note: The main bowl lid cannot be fitted if the mini bowl is not located correctly.

3. Place the knife blade over the drive shaft 16.

4. Add the ingredients to be processed.

5. Fit the lid and switch it on.

safety

• Never remove the lid until the knife blade has completely stopped.
• The knife blade is very sharp – always handle with care.

important

• Do not process spices – they may damage the plastic.
• Do not process hard food such as coffee beans, ice cubes or chocolate – they may damage the blade.

hints

• Herbs are best chopped when clean and dry.
• Always add a little liquid when blending cooked ingredients to make baby food.
• Cut foods such as meat, bread, and vegetables into cubes approximately 1-2 cm (1⁄2 –3⁄4 in) before processing.
• When making mayonnaise add the oil down the feed tube.

Compact chopper/grinder (if supplied)

Use the compact chopper/grinder for processing dry ingredients such as nuts, and coffee beans and it is also suitable for processing a range of spices such as Black peppercorns,  cardamom seeds, cumin seeds, coriander seeds, fennel seeds, fresh ginger root, fresh chilies, and whole cloves.

a sealing ring
b blade unit
c glass jar

to use your compact chopper/grinder

1. Put your ingredients into the jar. Fill it no more than half full.
2.  Fit the sealing ring to the blade unit.
3. Hold the underside of the blade unit and insert the blades into the jar – turn anti-clockwise to lock 17.
4. Place the compact chopper/grinder onto the power unit and turn clockwise to lock 18.
5. Use the Auto button, or select a speed (refer to the recommended speed chart).

safety

• Never fit the blade unit to your food processor without the jar fitted.
• Never unscrew the jar while the compact chopper/grinder is fitted to your appliance.
• Do not touch the sharp blades – Keep the blade unit away from children.
• Never remove the compact chopper/grinder until the blades have completely stopped.
• To ensure the long life of your compact chopper/grinder, do not run it continuously for longer than 60 seconds. Switch off as soon as you have got the right consistency.
• The appliance will not work if the compact chopper/grinder is incorrectly fitted.
• Do not process turmeric root in the compact chopper/grinder as it is too hard and may damage the blades.

hints

• For optimum performance when processing spices we recommend that you do not process more than 100g at a time in the compact chopper/grinder.
• Whole spices retain their flavor for a much longer time than ground spices so it is best to grind a small quantity fresh at a time to retain the flavor.
• To release the maximum flavor and essential oils whole spices are best roasted prior to milling.
• Cut ginger up into small pieces before processing.
• For best results, the mini bowl attachment is recommended when chopping herbs.

citrus juicer (if supplied)
Use the citrus juicer to squeeze the juice from citrus fruits (eg oranges, lemons, limes, and grapefruits).
a cone
b sieve

to use the citrus juicer

1. Fit the bowl onto the power unit, and add the detachable drive shaft.
2. Fit the sieve into the bowl – ensuring the sieve handle is locked into position directly over the bowl handle 19.
3. Place the cone over the driveshaft turning until it drops all the way down 20.
4. Cut the fruit in half. Then switch on and press the fruit onto the cone.
   • The citrus juicer will not operate if the sieve is not locked correctly.
   • For best results store and juice the fruit at room temperature and hand roll on a worktop before juicing.
   • To help with juice extraction move the fruit from side to side when juicing.
   • When juicing large quantities, empty the strainer regularly to prevent the build-up of pulp and seeds.

metal juice extractor (if supplied)

Use the centrifugal juicer for making juice from firm fruit and vegetables.

d filter drum

to use the juice extractor

1. Fit the drive adaptor onto the power unit 21– push down lightly to ensure the adaptor is located correctly.
2. Then fit the bowl. Place the handle towards the back and turn clockwise until it locks cm.
3. Place the pulp remover into the filter drum – ensuring the tabs locate with the slots in the bottom of the drum 22.
4. Fit the filter drum co.
5. Place the attachment lid onto the bowl, turn until it locks and the feed tube sits over the handle cp. Your juice extractor will not operate if the bowl or lid is not fitted correctly into the interlock.
6. Place a suitable glass or jug under the juice outlet.
7. Cut the food to fit the feed tube.
8. Select Auto and push down evenly with the pusher – never put your fingers in the feed tube. Process fully before adding more.
   • After adding the last piece, let the juice extractor run for a further 30 seconds to extract all the juice from the filter drum.

safety
• Do not use the juice extractor if the filter is damaged.
• Only use the pusher supplied. Never put your fingers in the feed tube. Unplug before unblocking the feed tube.
• Before removing the lid, switch off and wait for the filter to stop.

important
• If the juice extractor starts to vibrate, switch off and empty the pulp from the drum. (The juice extractor vibrates if the pulp becomes unevenly distributed).
• maximum capacity that can be processed at one time is 1Kg of fruit or vegetables (refer to speed chart).
• Some very hard foods may make your juice extractor slow down or stop. If this happens switch off and unblock the filter.
• Switch off and clear the pulp collector regularly during use. hints
• Before processing remove stones and pips (eg pepper, melon, plum) and tough skins (eg melon, pineapple). You don’t need to peel or core apples and pears.
• Use firm, fresh fruit, and vegetables.
• To maximize juice extraction place small quantities at a time in the feed tube and push down slowly.
• Citrus fruit – peel and remove the white pith, otherwise the juice may taste bitter. For best results use the citrus juicer.

Attachment storage box

Your food processor is supplied with a storage box for your bowl attachments and discs.

1. Fit the knife blade and discs into the storage box when not in use 26.
2. The storage box is fitted with a safety lock – close the lid to the lock. To open, push the tab in 27 and lift up the lid 28.

Care & cleaning

• Always switch off and unplug before cleaning.
• Handle the blades and cutting discs with the care they are extremely sharp.
• Some foods may discolor the plastic. This is perfectly normal and won’t harm the plastic or affect the flavor of your food. Rub with a cloth dipped in vegetable oil to remove the discoloration.

power unit

• Wipe with a damp cloth, then dry. Ensure that the interlock area is clear of food debris.
• Don’t immerse the power unit in water.
• Store excess cord in the storage area at the back of the power unit ct.

blender and compact chopper/grinder

1. Empty the goblet/jar, and unscrew the blade unit by turning to the unlock position to release.

2. Wash the goblet/jar by hand.

3. Remove and wash the seals.

4. Don’t touch the sharp blades – brush them clean using hot soapy water, then rinse thoroughly under the tap. Don’t
   immerse the blade unit in water.

5. Leave to dry upside down.

dual whisk

• Detach the beaters from the drive head by gently pulling them free. Wash in warm soapy water.
• Wipe the drive head with a damp cloth, then dry. Do not immerse the drive head in the water.

folding tool

• Detach the beater from the drive head by pressing the release button 10. Wash in warm soapy water.
• Wipe the drive head with a damp cloth, then dry. Do not immerse the drive head in the water.

centrifugal juicer

• The cutting blades on the base of the filter drum are very sharp, take care when handling and cleaning the drum.

• Some foods may discolor the plastic. This is perfectly normal and won’t harm the plastic or affect the flavor of your food. Rub with a cloth dipped in vegetable oil to remove the discoloration.
  juice drive adaptor

• Wipe with a damp cloth, then dry

• Do not immerse the adaptor in water.

all other parts

• Wash by hand, then dry.
• Alternatively, they are dishwasher safe and can be washed on the top rack of your dishwasher. Avoid placing items on the bottom rack directly over the heating element. A  short low temperature (Maximum 50°C) program is recommended.

whisk beaters/folding tool paddle
Do not immerse the drive head in the water| ✓
blender goblet, lid, filler cap| ✓
blade unit and seal for blender| X
blade unit and seal for compact chopper/grinder| X
compact chopper/grinder jar| ✓
citrus juicer| ✓
metal juice extractor| ✓
juice drive adaptor| X
spatula| ✓

Service & customer care

• If the cord is damaged it must, for safety reasons, be replaced by KENWOOD or an authorized KENWOOD repairer.

• If you experience any problems with the operation of the processor, before calling for assistance refers to the troubleshooting guide.
  If you need help with:

• using your appliance or

• servicing or repairs

• Contact the shop where you purchased your appliance.

• Designed and engineered by Kenwood in the UK.

• Made in China.

IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC.
At the end of its working life, the product must not be disposed of as urban waste.
It must be taken to a special local authority differentiated waste collection center or to a dealer providing this service.
Disposing of a household appliance separately avoids possible negative consequences for the environment and health deriving from inappropriate disposal and enables the constituent materials to be recovered to obtain significant savings in energy and resources. As a reminder of the need to dispose of household appliances separately, the product is marked with a crossed-out wheeled dustbin.

No power/indicator light not lit.
Bowl is not fitted to the power unit correctly.
Bowl lid is not locked on correctly.
Eco function operating.| Check processor is plugged in.
Check bowl is located correctly and the handle is situated
towards the right-hand side.
Check that the lid interlock is located correctly into the handle area.
The processor will not work if the bowl and lid are fitted incorrectly.
Press either the Auto Button or turn speed control on, then return to ‘0’ to switch off the Eco function.
If none of the above check the fuse/circuit breaker in your home.
The compact chopper/grinder will not operate.| Compact chopper/grinder is not locked on correctly.
Compact chopper/grinder not assembled correctly.| The compact chopper/grinder will not operate if fitted incorrectly to the interlock.
Check blade unit is fully tightened onto the compact chopper/grinder jar.
A blender will not operate.| Blender is not locked on correctly.
Blender was not assembled correctly.| The blender will not operate if fitted incorrectly to the
interlock.
Check blade unit is fully tightened into the goblet.
The processor stops or slows during processing.| Overload protection operated.
Processor overloaded or overheated during operation.
Maximum capacity exceeded.| Switch off, unplug and allow the appliance to cool down for approximately 15 minutes.
Refer to the speed chart for maximum capacities to process.
Weighing function
Display screen freezes on [- – – -1.
Weight changed on the display screen.| The quantity weighed too small.
The power unit moved during operation.| Use teaspoon and tablespoon measures for very small
quantities.
Do not move the unit during use. Zero the display before
weighing next ingredients.
Power On light flashing rapidly.| Normal operation.
The light will flash if the bowl, lid, or blender is not fitted to the power unit or not locked in place correctly.| Check interlocks are engaged correctly.
Power On light flashing slowly.| Normal operation.
The food processor was left plugged in for over 30 minutes without being operated and went into Eco mode.| Press either the Auto Button or turn speed control on and then return to ‘0’ to switch off the Eco function.
Auto and Power On light flashing.| Normal operation.
The light will flash if the Auto is selected but interlocks are not engaged.| Check interlocks are engaged correctly or press the Auto button to switch off the Auto function.
Blender or compact chopper/grinder
leaking from blade assembly base.| Seal missing.
Seal incorrectly fitted.
Seal damaged.| Check the seal is fitted correctly and not damaged. To obtain a replacement seal see “service & customer care”.
Blender seal missing from blade unit when removed from packaging.| The seal is packed pre-fitted to the blade unit.| Unscrew the goblet and check that seal is fitted to the blade unit.
To obtain a replacement seal see “service & customer care”.
Poor performance of tools/attachments.| Refer to hints in the relevant “using the attachment” section. Check attachments are assembled correctly.

HEAD OFFICE: Kenwood Limited, 1-3 Kenwood Business Park, New Lane, Havant, Hampshire PO9 2NH
kenwoodworld.com

CREATE MORE

Documents / Resources

| KENWOOD Multipro Excel FPM910 Food Processor [pdf] Instructions
FPM90, FPM91, Multipro Excel FPM910 Food Processor, Multipro Excel FPM910, Food Processor
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>