ZEVNI Z-67ZVJRY2-4569 3-Light Plated Brass Island Hanging Chandelier Modern Pendant Light Instruction Manual

Z-67ZVJRY2-4569 3-Light Plated Brass Island Hanging
Chandelier Modern Pendant Light
Instruction Manual

Z-67ZVJRY2-4569 3-Light Plated Brass Island Hanging Chandelier Modern

Pendant Light

Item Number: Z-67ZVJRY2-4569
WARNING (To reduce the risk of fire, electric shock, or personal injury):

1. We suggest installation by a licensed electrician.

2. Please read the instruction carefully and save it as you may need it at a later time.

3. Before you start, NEVER attempt any work without shutting off the electricity until the work is done.
   A) Go to the main fuse, or circuit breaker, box in your home.
   Place the main power switch in the “OFF” position.
   B) Place the wall switch in the “OFF” position.

4. The mounting surface should be clean, dry, flat, strong enough and 1/4” larger than the canopy on all sides. Any gaps between the mounting surface and canopy exceeding 3/16” should be corrected as required.

5. Make sure that the ceiling or wall can stand the weight of the lamp before installation.

6. Make sure the voltage you are using is 120V. The maximum wattage is 60W per bulb.

7. Keep the lamp away from acidic and alkaline substances in case of damaging the surface of the lamp.

8. When replacing bulbs, you should turn off or unplug the lamp and you must wait until it is cool as bulbs get hot quickly.

9. The safety instructions appearing in this manual are not meant to cover all possible conditions that may occur. It must be understood that common sense, caution, and care must be used with any electrical products.

IMAGE FOR FINISHED PRODUCT:

TOOLS REQUIRED (NOT INCLUDED):
Before starting assembly and installation please prepare the needed tools as below picture

PARTS TYPE & QTY INCLUDING:

ASSEMBLY & INSTALLATION INSTRUCTIONS:

1. Carefully remove the fixture from the carton and check that all parts and accessories are included as shown in the above illustration.

2. Make pre­installation
   Step A1: According to your desired hanging height to choose and use tubes (J).
   Pass fixture wires through the chosen tubes (J), and tighten tubes (J) onto fixture body (K).
   Step A2: Open quick links (I). Attach quick links (I) to loops (F) on canopy (E) and tubes (J).
   Close Quick links (I).

3. Turn off power
   Before you start the installation, NEVER attempt any work without shutting off the electricity until the work is done.
   A) Go to the main fuse, or circuit breaker, box in your home.
   Place the main power switch in the “OFF” position.
   B) Place the wall switch in the “OFF” position.

4. Make installation
   

Step B1: Unscrew the hex nut (G) and cap nut (H) from the single bar (C).
Step B2: Attach single bar (C) to the outlet box with mounting screws (B).
Note: the side of the single bar (C) marked “GND” must face out.
Step B3: If needed, shorten the length of the fixture wires. At this point, the remaining wire length measured above the single bar (C) is at least 6″.
Step B4: Make wire connections
Connect wires as below wires connection shown. PLEASE NOTE THAT GROUND WIRE IS
BARE COPPER WIRE, NEVER CONNECT OTHER WIRES TO GROUND WIRES.

Connect ground wires according to the below chart

Connect wires according to the below chart

Twist wires together with plastic wire connectors until tightly joined, and wrap each connector with approved electrical tape. Be sure that no wire strands are exposed and then carefully tuck all wires into the outlet box.
Step B5: Raise canopy (E) to the ceiling and secure canopy (E) in place by tightening hex nut (G) and cap nut (H) onto the pre­assembled threaded nipple on the single bar (C).
NOTE: The canopy (E) should be snug against the ceiling and cap nut (H).
If not, adjust the threaded length of the pre­assembled threaded nipple on a single bar (C) by unscrewing the pre­assembled hex nut and then screwing the pre­assembled threaded nipple in or out of the single bar (C) until the secure length is achieved.
Tighten the pre­assembled hex nut and back to step B5.
Step B6: 1) Unscrew socket rings (N) from sockets (L). Place glass shades (M) on sockets (L), then secure them with socket rings (N). 2) Install bulbs (not included) (Please do  not exceed the maximum wattage recommended on the socket.)
Check everything is already installed properly, then you could turn on the light. Enjoy!

ORDERING PARTS.
Keep this sheet for future reference in case you need to order replacement parts. All parts for this fixture can be ordered from the place of purchase.
Be sure to use exact wording from illustrations when ordering parts.

CLEANING.
To clean, wipe the fixture with a soft cloth. Do not use abrasive materials such as scouring pads or powders, steel wool, or abrasive paper.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>