Safecourt Kitchen BL100 Kitchen BLENDER Smoothie set User Manual

Safecourt Kitchen BL100 Kitchen BLENDER Smoothie set

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety
Precautions should always be taken, including the Following:

1. READ ALL INSTRUCTIONS.
2. Unplug from outlet when not in use, before putting on or taking off parts, And before cleaning or removing contents from blender container. Never put hands into the blender container, or handle the blades with appliance plugged in.
3. To protect against electrical hazards, and permanent damage to unit, do not put motor base of blender in water or other liquids.
4. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
5. Children should be supervised to ensure that they do not play with the appliance.
6. Do not use carbonated liquids in the blender container, or in any blending container. Using carbonated liquids in a blender container may result in injury.
7. Do not pour boiling water into the blender container.
8. Do not blend liquids for more than 7 minutes.
9. Avoid to contact with moving parts.
10. Do not operate this blender or any other appliance with a damaged cord or plug, or after the appliance malfunctions or is dropped or damaged in any manner. You need to return appliance to the nearest authorized service facility for examination, repair, or electrical or mechanical adjustment.
11. The use of attachments, including canning jars, not recommended by the manufacturer may cause a risk of injury to persons
12. Do not use it outdoors.
13. Do not let cord hang over edge of table or counter, or touch hot surfaces.
14. Keep hands and utensils out of container while blending to prevent the possibility of severe personal injury and/or damage to the blender. A plastic scraper may be used, but must be used only when the blender is not running.
15. Blades are sharp. Handle carefully.
16. Always operate blender with cover in place.
17. See Cleaning and Maintenance instructions. Add: Not for water jet cleaning.
18. Always operate blender with jar buffering properly in place.
19. Do not fill above MAX FILL LINE for blending.
20. If the container overflows during blending, there is too much liquid/ ingredients in the container. Stop blending, remove enough liquid/ ingredients to below MAX FILL LINE, and continue blending. Do not operate if overflowing.
21. Do not operate your appliance in an appliance garage. When storing in an appliance garage, always unplug the unit from the electrical outlet. Not doing so could create a risk of fire, especially if the appliance touches the walls of the garage or the door touches the unit as it closes.
22. The use of ear protection is recommended during extended operating periods.
23. Ensure the jar coupler and motor coupler are aligned and engaged before operating. If unable to engage, remove container and shake contents, and then try again.
24. The coupling seat may be hot after running ­ do not touch. 25. Replace jar buffering if worn.

To Reset the Unit

Your blender is equipped with a Resettable Thermal Protector to protect the motor. If the motor shuts down, unplug the blender. Let the blender rest for approximately 15 minutes. Once the resting period has elapsed, plug the power cord back into the outlet and continue blending. If your blender does not function properly following this procedure, discontinue use and contact a certified Consumer Service Center.

SAVE THESE INSTRUCTIONS FOR HOUSEHOLD USE ONLY

Unpacking Instructions

1. Place the box containing blender on a flat, sturdy surface before unpacking.
2. Open box and remove instruction book, Handbook cookbook, and any printed materials from top of box.
3. Remove packing materials and all components. CAUTION: Sharp blade inside blender container.
4. Place all packing materials back into the gift box and save, in the event that future shipping of the machine is needed.

Features and Components

1. Take the measuring cup up.
2. Cover opening.
3. Glass -1500mL, BPA free Eastman Tritan, includes English and metric calibration.
4. Blender base with high performance motor, and with metalring.
5. The glass with plastic handle needs to be screwed into the mainframe with the handle facing the bottom trigger link.There is a lock symbol next to it (FIG 1)
6. Another glass can be screwed into the main Housing in all four directions.

1. Unscrew the lid or tool apron.
2. Portable cup -600ml, AS. (FIG 2)
3. The portable cup and grinding cup that holds the tool apron can be screwed into the mainframe to make recipes. (FIG 3)
4. Grinding cup-50g coffee bean, AS. (FIG 4)

Control Panel

Operating Instructions

Place the motor base on a flat, sturdy surface, it is so important that the surface is clean and dry fit the jar on motor base, once assembled, plug the power cord into an electrical outlet.

Add all necessary ingredients to jar and secure the cover; you may add more ingredients by removing the measuring cup and dropping ingredients through the fill area, replace the measuring cup after adding any ingredient.

Do not put hands in jar with the blender plugged in, start blending

All actions are ready, manual mode and pre-setting program mode are ready for your choice. The unit will work once you definite any modes.

After power on, the knob should be at the “OFF” position when plug in, and the buzzer beeps twice. When the machine does not work, it must turn back to OFF.

Preset Function

“OFF” : After the blender is powered on.when the knob is in the OFF file,the buzzer will beep 2 times and the blender will not work

“ ” : Cleaning program: After power on,wait for the blender to start working in this gear for 1.5s. In 2s, soft accelerate to 5 and run 2s and then pause 2s, This is a loop. repeat 10 cycles after the machine stops running.

“ ” : Fruit and vegetable shortcut program: After power on, the blender works in accordance with the set program at this gear, and stops running after a total of 2min.

“ ” : Nuts Shortcut program: After power on, wait for 1.5s, the blender start toworking,The blender will work in accordance with the set program for 1min and then stop.

“ ” : Milkshake Shortcut program: After power on, wait for 1.5s, the blender start to working, The blender will work in accordance with the set program for 1min and then stop.

“ 1-5” : The blender accelerates gradually from gear 1 to 5

Helpful Reminders

• Jar cover should always be secure while the unit is in operation. Always use the blender on a clean, sturdy and dry surface.
• Insert the measuring cup into the cover.
• Once the cover is in position, additional ingredients can be added during blending by simply removing the measuring cup insert, adding ingredients, and replacing it, turning it to secure.
• Do not place jar on base while motor is running or remove jar before the blender has stopped running.
• Do not attempt to blend boiling liquids
• When blending, place liquid ingredients into the jar first, followed by the softest ingredients. Ice or frozen fruit should be placed in the jar last.
• Use a plastic spatula as needed, only when the blender is turned off. Never use metal utensils, as damage may occur to the jar or blade.
• Blending hard ingredients and spices may cause some clouding to appear on the inside of the jar, but will not affect blender performance.
• Use Ice crush and Cleaning program for maximum power to break up hard ingredients.
• Do not exceed the MAX FILL LINE when adding food or liquid to the blending jar
• Make sure the jar is completely dry when chopping ice, fresh herbs, garlic, onion, zest, breadcrumbs or nuts and spices.
• Do not store food or liquids in your jar.
• Be careful not to over process foods.
• Do not use any utensil inside the jar with the motor on.
• Unplug blender before reaching into the jar.
• Never use carbonated liquids in a jar. Using carbonated liquids in the blender may result in Injury

Blender Cleaning and Maintenance

Always unplug the blender from the electrical outlet before cleaning. Never immerse blender base in water or other liquids.

1. Remove the jar from the blender base and remove the cover. The jar must be cleaned and dried after each use or when the blender has not been used for an extended  period of time. We recommend using the automatic clean function
2. Wash the cover in warm, soapy water and rinse thoroughly.
3. The jar, blade assembly and cover assembly are all dishwasher safe.
4. To clean the blender base, wipe the exterior with a soft cloth or sponge dampened with cleaning solution. Do not immerse the base in cleaning solution or water. Wipe with a dry towel and be sure the base is completely dry before using.
5. Be sure that the blender is thoroughly dry and properly assembled with the jar pad in place before operating. An authorized service representative should perform any other servicing.

Environment

| Do not dispose of electrical appliances as unsorted municipal waste, use separate collection facilities. Contact your local government for information regarding the collection systems available. If electrical appliances are disposed of in landfills or dumps, hazardous substances can leak into the groundwater and get into the food chain, damaging your health and well-being. When replacing old appliances with new ones, the retailer is legally obligated to take back your old appliance for disposals at least free of charge.
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>