Gude BSS 18 Impact Wrench Instruction Manual

BSS 18 Impact Wrench
Instruction Manual

BSS 18 Impact Wrench

Starting-up the machine

Operation

Technical Data

-1
Torque max.| 180 Nm| 230 Nm
Rate of percussion under load| 0 – 3000 min-1| 0 – 3000 min-1
Tool reception| 1/4“ (6,35mm)| 1/2“ (6,35mm)
Weight without battery/Charging equipment| 1,1 kg| 1,1 kg
Noise details
Sound pressure level LpA| 95,1 dB (A)| 95,1 dB(A)
Sound power level LWA| 106,1 db (A)| 106,1 db (A)
Measured according to EN 60745; Uncertainty K = 3 dB (A)
Wear ear protectors!
Vibration details
Vibration total values (triaxial vector sum) determined according to EN 60745
Impact tightening of fasteners of the maximum capacity of the tool:
Vibration emission value ah| 15,87 m/s²| 15,87 m/s²
Uncertainty K = 1,5 m/s2| |

WARNING: The vibration emission level will vary because of the ways in which a power tool can be used and may increase above the level given in this information sheet.
The vibration emission level may be used to compare one tool with another.
It may be used for a preliminary assessment of exposure.
An accurate estimate of the vibratory load should also take into account the times when the tool is shut down or when it is running but not actually in use. This may significantly reduce the vibratory load over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintaining the tool and the accessories, keeping the hands warm, and organization of work patterns.

Read and understand the operating instructions before using the appliance. Familiarise yourself with the control elements and how to use the appliance properly. Abide by all the safety measures stated in the service manual. Act responsibly toward third parties.
The operator is responsible for accidents or risks to third parties.
Persons over 16 years of age can only work on the appliance. An exception includes youngsters trained in order to reach knowledge under the supervision of the trainer during occupational education.
In case of any doubts about connection and operation refer, please to our customer center

Specified Conditions Of Use

The impact wrench can be used to tighten and loosen nuts and bolts.
As a control measure, always check the tightening torque with a torque wrench.
Do not use this product in any other way than stated for normal use. Not observing general regulations in force and instructions from this manual does not make the manufacturer liable for damages.
In spite of compliance with all relevant design regulations, dangers may still present themselves when the machine is operated, e.g.:

• noise emissions
• dust emissions
• vibrations to hand and arms

Emergency procedure
Conduct a first-aid procedure adequate to the injury and summon qualified medical attendance as quickly as possible. Protect the injured person from further harm and calm them down. If you seek help, state the following pieces of information: 1. Accident site, 2. Accident type, 3. A number of injured persons, 4. Injury type(s)

Symbols

| WARNING/CAUTION!
---|---
WARNING – Read the operating instructions to reduce the risk of injury.
Wear eye protective goggles!
Wear ear protectors!
Take the replaceable battery from the appliance before any extension, cleaning or servicing works.
CE marking
Any damaged or disposed of electric or electronic devices must be delivered to appropriate collection centers.

Battery

| Protect the battery against heat and fire.
---|---
Protect the battery against water and moisture.
Protect the battery against temperatures above 40°C.
Do not throw the batteries in household waste.
Deliver the batteries to a collection center of old batteries where they will be recycled in an environmentally friendly way.

WARNING Read all safety warnings and all instructions.  Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
Safety information for impact wrenches
Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a „live“ wire may make exposed metal parts of the power tool „live“ and could give the operator an electric shock.

Additional Safety and Working Instructions

Wear ear protectors. Exposure to noise can cause hearing loss.
Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, and ear defenders. The dust produced when using this tool may be harmful to health. Do not inhale the dust.
Use a dust absorption system and wear a suitable dust protection mask. Remove deposited dust thoroughly, e.g. with a vacuum cleaner. Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.
Check all screw and plug-in connections and protective equipment if firm and tightened properly and whether all moving parts are running smoothly whenever the appliance is to be put into operation.
The appliance must not be used if damaged or if safety equipment is defective. Replace any worn-out and damaged parts.
Do not use the device near flammable liquids or gases. Risk of fire and explosion in case of a short circuit.
Please turn the device immediately off when the tool used gets blocked! Do not turn the device on again when the tool is still blocked. This could cause a bounce back with a high reaction moment. Determine and remove the cause of the blocking of the tool used while respecting the safety instructions.
The possible causes may be:

• it is tilted in the workpiece to be machined
• it has pierced through the material to be machined
• the power tool  is overloaded

Battery

Risk of fire! Risk of explosion!
Never use damaged, defective, or deformed accumulators. Never open or damage the accumulator or let it fall on the ground. Umgebungstemperatur Protects the battery against heat and fire. Battery to be used at ambient temperatures between 10°C and +40°C only. Never put the battery on heaters and do not expose it to strong sunlight for a long time. After being subject to heavy load, let the battery cool down first. Short circuit – do not bridge the accumulator contacts with metal parts. The accumulator must be packaged (plastic bag, box) or accumulator contacts must be sealed up for accumulator disposal, transport or storage.

Dispose of the batteries in an environmentally friendly manner.
Li-ion batteries are subject to special disposal obligations. Have any defective batteries been disposed of by a specialized shop? The battery must be taken out before the appliance is scrapped. Damaged batteries may harm the environment and your health if toxic vapors or liquids leak out of such batteries.
Therefore, never send a defective battery by post, etc.
Please contact your local recycling center.
Dispose of the batteries when discharged. We recommend applying adhesive tape on the poles to protect them against short circuits. Never open the battery.

Maintenance

Take the replaceable battery from the appliance before any extension, cleaning or servicing works.
Repairs and works specified in these Instructions may only be performed by qualified authorized staff. Use only original accessories and original spare parts.
Keep the device, in particular the air vents, clean at all times. Never spray water on the device’s body!
Do not clean the plastics with solvents, or flammable or toxic fluids. For cleaning, use a damp cloth only.
Only a regularly maintained and treated appliance can serve as a satisfactory aid. Insufficient maintenance and care can lead to unforeseen accidents and injuries.
If necessary, a list of spare parts can be found at www.guede.com.

Guarantee

The warranty period of 12 months applies to commercial use and 24 months applies to private use and commences on the day of purchase of the device.
The guarantee solely covers inadequacies caused by material defects or manufacturing defects. An original payment voucher with the date of the sale needs to be submitted for any claim in the guarantee period. The guarantee does not cover any unauthorized use such as appliance overloading, use of violence, or damage as a result of any unauthorized interference caused by foreign items. Failing to follow the operating  and assembly instructions and common wear are also not included in the guarantee.

Important information for the customer
Please note that returns within or outside the warranty period should always be in the original packaging. This measure effectively avoids unnecessary transport damage and any associated disputed ruling. Your equipment is optimally protected only in the original box, and keeping it in that box will ensure smooth processing.

Service

Do you have any technical questions? Any claim? Do you need any spare parts or operating instructions? We will quickly help you without needles bureaucracy on our web pages at www.guede.com in the Servicing part. Please help us be able to help you. In order to identify your device in case of claim we need the serial No., product No. and year of production. All this data can be found on the type label. To always have these data at hand, please enter them below.

Serial No.:————————–
Art. No:————————–
Year of production:————————–

Tel.: +49 (0) 79 04 / 700-360
Fax: +49 (0) 79 04 / 700-51999
E-Mail: support@ts.guede.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>