KUGOO S1 Portable Electric Scooter User Manual

S1 Portable Electric Scooter
User Manual

Portable Electric scooter

Thank you for purchasing our products
Please carefully read the user manual
And warranty book before using

MAIN PARTS

SAFETY

1. The product is for adults only, limited to one adult, please do not carry two adults at the same time. Is not suitable for minors.
2. Please wear your safety helmet and other protective equipment when riding.
3. Do not ride in a traffic lane or on unsafe roads and do not break local regulations
4. Please exercise in wide areas, and ride after skilled manipulation, do not ride in the traffic lanes.
5. Do not make any dangerous actions when riding or riding with one hand. Keep your feet on the scooter.
6. Do not attempt to ride the scooter on stairs that are above 3 cm; it may overturn the scooter causing injury or damage. Please try to avoid also the stairs smaller than 3 cm. It also may cause injury or damage.
7. The scooter’s highest speed is 30 Km/h. For your safety, please limit the speed to 20 Km/h. Please try to avoid using it at night, if needed, please limit the speed to 15 K/h or less and turn on the headlight.
8. Do not use a scooter when the temperature is lower than -5 ºC.
9. Please slow down or get off when riding in rough or poor road conditions.
10. Do not ride the scooter in oily or icy surface terrain.
11. Please adjust the height of the handlebar according to your height to ensure safe riding.
12. Do not immerse the scooter in the water with a depth of 4 cm or spray it directly with water to avoid damage of the electrical parts of the vehicle.
13. Please try to avoid riding in bad weather such as heavy rain and high winds to protect it.

PRODUCTS

Folding stages

Folding steps

1. Open the lock lever, in the direction of the arrow, as shown in figure (a).
2. Press the red button, figure (b), at the same time press down the handlebars as shown in figure (c), and push the lock lever to the lock position.
3. Hold the handlebar with both hands, pushbuttons (1) shown in Figure (d). Pull out the handlebar grips, figured, up to a maximum and fold downwards to reach that figure B, from the previous page.
4. Push the handlebar forward, and press the folding lever in the direction of the arrow in figure (f)
5. Continue folding the scooter until the folding hook reaches and hangs the bolt located on the rear brake

Unfolding steps

1. Press the rear brake in the direction of the arrow in figure (a) until the folding hook releases the bolt located on the rear brake. Then, lift the handlebar until it reaches the working position and the locking bolt comes into place, like in figure (b).
2. Raise the two handles of the handlebar until they automatically return to the work position, figure (c)
3. Push the lock lever in the direction of the arrow in Figure (d) and lift the handlebars to the desired height. Now press the button shown in Figure (e) and fix it in one of the two holes, as desired.

OPERATION

1. Introduction of Handlebar parts

1. Thumb Accelerator
2. Thumb Electronic Magnetic Brake
3. Horn Button
4. Setting Button
5. Switch Button
6. Light Button
7. Lcd Display
8. Speed level

Operating Instructions

a. ON/OFF
Press the switch for 1 sec, and the display lights indicate power on. Press for 3 seconds if you want to turn it off. It will turn off after being unused for 3 minutes.
b. Speed control
Press the right thumb accelerator to control the speed (1-30km/h). There are three-speed levels and press the Speed leve button to change.l
c. Braking Control
Press the left thumb electronic magnetic brake. The greater angle you press, the greater the braking force will be.
d. Horn
Turn on the power, press the horn button and it will hoot.
e. LED Headlight
Press the Light button when needed and there will be a sign-in display indicates the light is turned on. Press the button again when you do not need the light
f. Mileage Show
When powering on, It displays three modes: total, trip, and time. You can press the settings button to change it. When it displays the ‘trip’ mode, press the setting button for 3 seconds and it will clear the trip.( Single stroke accumulated more than 100 belongs to 100)
g. Emergency
Emergency, stamping the rear foot brake can simultaneously achieve front electronic magnetic brake and rear wheel friction brake; under normal circumstances, please do not use the emergency brake at high speed to avoid the wheel damage and the company shall not be responsible for this damage. Please repair it for pay.

Display Factory Setting

There are 5 buttons.They are Horn button(K5),Setting button(K4),Switch button(K3),Light button(K2),Speed Level(K1).
Press the k5 and k4 for 3sec to enter the parameter table.
a.k5 button: Short according to return to the running state, the modification is not effective
b.k4 button: Short press to the next parameter; Grow by more than 2 seconds, save the changes made, and return the running state.
c.k3 button : Not effective d.k2 button: Short press, reverse adjust the parameter.
e.k1 button: Short press, adjust parameter

Parameter table

| Default| Min| Max| Description
---|---|---|---|---
0| 1.0| | | Instrument version
1| 0| 0| 1| starting mode, 0= zero, 1= non-zero start,
2| 25| 0| 60| Km/h speed limit value, unit, 0 means no speed limit, the default of 25 km/h
3| 12.0| 4.0| ###| The wheel diameter, the unit inches, and 12 inches by default
4| 1| 1| 100| Speed measuring magnetic steel, 1 by default
5| 60| 30| 100| Not effective
6| 80| 30| 100| Not effective
7| 100| 30| 100| Not effective
8| 0| 0| 255| Not effective
9| 0| 0| 255| Not effective
10| 0| 0| 255| Not effective
11| 0| 0| 255| Not effective
20| 90| 0| 600| Automatic shutdown time, unit of s, I’m-‘- the default 90 seconds
22| 1| 0| 1| If EBS brake hall, 0 = don’t answer, 1 = EBS brake hall, 1 by default
99| 0| 0| 999| ODO data reset, when data is equal to the XXX (1) set up and confirm after reset ODO data

RIDING OPERATION

Ready

1. Choose a suitable venue for riding.
2. Expand the scooter in accordance with the description.
3. Adjust the T-pipe to the suitable height according to your height.

Start

1. Press the power button to turn on the power
2. Stand on foot on the scooter and leave another foot on the ground.
3. Gently press down on the right thumb accelerator, and the scooter will immediately move forward slowly. Place the foot which is on the floor on the pedal after smooth riding. Press the right thumb accelerator, the greater the angle you press, the faster it will be.

Brake

1. Under normal circumstances, by pressing the left thumb electronic magnetic brake, the scooter will immediately de-energize and then brake. The greater the angle you press, the greater the braking force will be.
2. Emergency, stamping the rear foot brake can simultaneously achieve an electronic magnetic front brake and rear wheel friction brake; under normal circumstances, please do not use the emergency brake at high speed.

BATTERY AND CHARGER

Each KUGOO electric scooter was equipped with a special lithium battery and a special smart charger, accessories carried by each scooter have a dedicated number, please do not use the charger of other brands, the charger is not appropriate to other company supplied chargers, too. If the battery or charger is damaged owing to these, the company shall not be responsible.
Battery
When you get the KUGOO electric scooter the first time, please charge the battery fully before using The battery can be charged at any time, in order to ensure that the battery has power, during which the battery will not charge for any damage Please charge the battery once every three months if stop using Due to water, collision, and other non-normal factors that lead to battery damage, which is not covered under warranty.
Charger
The company provides a dedicated charger that has a charging protection function, when the battery is 100% charged, the charger will automatically stop charging Charging time is no more than 3 hours Due to water, collision, and other non-normal factors that lead to battery damage, which is not covered under warranty.
Charge Description
Open the charging hole rubber protective cover, put the charger connector into the charging hole Connect the charger plug to the power socket It means it is charging when the charger light is red,; the charger light turns green when the battery is fully charged.

MAINTENANCE

Lubricating
Please add a small amount of grease or lubricants to handle folded position every six months Please check the scooter every three months whether the screws are loose, if yes screw
Battery
The lithium battery provided by the company can be recharged at least 500 times, and the normal use can reach more than 1,000 times. Every time after fully charged, the lithium battery needs to be replaced if the travel distance Is too short.
Placement and daily care
Do not exposure the scooter under the sun for too long or in other serious damp places Please keep the scooter clean

GENERAL TROUBLESHOOTING

Checklist
When the products have any problems, please refer to the following methods.

1. LED display black screen
   Reason: Exposure under the sun for too long.
   Solution: Place it in shadow and it will return to normal after a period.

2. Values that appeared do not fit the actual values
   Reason: Parameters are set incorrectly or missing.
   Solution: Please reset the display factory settings following the instructions

3. Digital display dim
   Reason: Bad battery contacts or the battery is dead
   Solution: Turn off the power then restart again, if the problem still occurs; please contact your local reseller.

4. When the product does not operate normally, check whether the following work is completed or not
   a. Turn on the battery
   b. Check the battery via the display if there is electricity
   c. Left thumb electronic brake and rear brake in place,
   d. All jacks and connector holes are linked accurately.

If the above steps are completed, the product still does not operate normally; please contact your local vendor or reseller.

PRODUCT SPECIFICATION SHEET

Note: Please follow the correct way to use our products, parts damages and other damages caused by abnormal use, the company shall not be responsible for.
In the warranty period, if the malfunction and damage caused by the following causes are not within the scope of the quality assurance:

1. Do not do the proper maintenance and repair in accordance with the instruction manual.
2. Use the electronic scooter for other purposes such as performing super dangerous actions, resulting in damage or functional failure.
3. Disassemble or use of any external factory components
4. Wrong uses, traffic accidents, or accidental collisions damage the body and the body parts.
5. Stickers insufficiency, water, and parts numbers do not match
6. Ride on the non-normal roads causes damage or failure to use
7. Operating rental of improper use or non-licensed
8. Scourge or irresistible reason

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>