InXamax Solar Powerbankstruction Manual
- June 5, 2024
- Xamax
Table of Contents
Solar Powerbank
Manual/Handleiding
Powerbank introduction
- The Xamax solar powerbank is a portable solar charger powerbank. It supports QC2.0/QC3.0 Output Fast Charging Protocol, FCP/AFC/SFCP Input and Output Fast Charging Protocol, MTK PE+1.1&2.0 Output Fast Charging Protocol, USB C/PD2.0/PD3.0 Input and Output Protocol, USB-C PD3.0 PPS Output Protocol, compatible with BC1.2/Apple/Samsung Mobile Phone. The charging input terminal of the powerbank is micro-USB, TYPE-C interface, and solar energy input, using constant current and constant voltage charging mode to charge the built-in battery; USB2, USB3, USB4 is a normal output 5V/3A; USB1: supports QC2.0/QC3.0 DC 5V/3.0A 9V/2A 12V/1.5A; TYPE-C input: DC 5V/3A 9V/2A, output: DC 5V/3.0A 9V/2A 12V/1.5A, supports PD2.0/PD3.0 PPS FCP AFC SFCK MTK bidirectional fast charging protocol. USB1 and TYPE-C are fast charging interfaces, and only 5V output is supported when two or more output interfaces are used at the same time. It can supply power and charge for various brands of mobile phones, IPAD, PSPs, MP3/MP4, PDA,s and other digital products.
- Using the latest intelligent fast charge and discharge management chip, the efficiency is up to 90%, multiple intelligent protection functions, safe/reliable use, and ultra-low self-consumption.
- Built-in large capacity Li-Polymer battery, ultra-long endurance.
Specifications
Micro Input: DC 5V/2A 9V/2A
TYPE-C Input: DC 5V/3A 9V/2A
Solar Charging: DC 5V/1.5W
Output1: DC 5V/3A 9V/2A 12V/1.5A
Output2/3/4: DC 5V/3A
TYPE-C Output: DC 5V/3A 9V/2A 12V/1.5A
Wireless Output: 10W
Power ON/OFF button operation instructions
Press the ON/OFF button to turn on the wireless charging function and wake up
the output function of each port, and display the battery power. At the same
time, when the red light flashes three times, the long light indicates that
the wireless charging has started. At this time, it is detected that the
correct wireless charging and receiving terminal or load will turn on the
green light; when the wireless charging and indicating lamp is full, it will
turn off. Double-click to turn on or off the LED lights. In the state of the
LED lights on, click the button to switch to high, low, flashing, and SOS.
Functions display
1. Solar panel
2. Lanyard
3. Solar charging indicator
4. USB output port 1/2/3/4
5. USB silica gel plug for protection| 6. Micro/Type-C input port
7. Power indicator
8. ON/OFF button
9. LED lighting
10. Wireless charger indicator
11. Wireless charger
---|---
Charging digital equipment
- Short press the ON/OFF button to start the powerbank and to supply power to the USB output. At this time, the powerbank and the digital device can be charged by connecting the charging cable* to the powerbank and the digital device.
- When the powerbank is on standby, connect the digital device with the charging cable* to the powerbank. The powerbank can automatically start charging the digital device without pressing any button.
- When the output USB ports are not connected to the charged device for 30 seconds or when the charged device is full, the powerbank will turn off all output and power displays. Then it will enter a low power standby state.
Pay attention: Please charge the powerbank with a USB TYPE-C cable, or the included USB cable and DC5V/2A adapter. Because of the high capacity of 30.000 mAh, it could take up to 3x longer to charge with a DC5V/1A adapter.
- Charging cable of the digital device.
Adapter charging
When the external DC power supply is connected to the powerbank through micro-
USB or TYPE-C, the powerbank will charge the built-in battery. Four blue LEDs
will automatically light up the current power of the product, as follows:
Solar panel charging
The best way to receive sunlight illumination is at 45 degrees. The built-in
charging circuit automatically charges the built-in battery.
The solar indicator light is always green, which indicates that the solar
panel is charging the battery. To view the power consumption, press the power
ON/OFF button.
Power volume review
Press the ON/OFF button at the side of the powerbank, and the powerbank starts
to supply power to the USB output. The LED power indicator shows the power
volume as shown in the below table.
After 30 seconds of not connecting to the load, the powerbank shuts down and
enters the standby state.
Wireless charging
Press the button to enter the wireless charging state. When using the wireless
charging function alone, the maximum output can be 10W to charge your product.
When USB1, USB2, USB3, USB4, and TYPE-C are used at the same time or the
current is in the range of 2.5A, the wireless charging will automatically
switch to 5W. If the wireless charger is more than 3A, it will automatically
turn off.
LED lights instructions
Double-click the ON/OFF button to turn on the LED lights when the illumination
lamp is off. Click the button to switch to high, low, flashing, and SOS.
PROTECTION FUNCTION
Input Undervoltage undercurrent protection
If an adapter with actual specifications less than 5V/2.1A is used to charge
the powerbank (such as a 5V/1A adapter), the powerbank will automatically
adapt to the output current of the adapter (automatically reduce the charging
current of the built-in battery) to prevent damage to the adapter.
Input short circuit protection
If the powerbank input short circuit is caused by improper use or other
factors (such as charging cable breakage short circuit), the powerbank will
automatically shut off the charging circuit to prevent product damage and
battery power backfilling.
Output overcurrent protection
If the output current of any USB is more than 3.2A due to improper use or
other factors, the powerbank will automatically turn off the output to protect
the charged device and the powerbank itself. When the short circuit is
removed, if the flashing of the button power display is extinguished after
four times, it needs to be charged and activated again to start the discharge.
Output short circuit protection
If any USB output is short-circuited due to improper use or other factors, the
powerbank will automatically turn off the output to protect the charged device
and the powerbank itself. When the short circuit is removed, if the flashing
of the button power display is extinguished after four times, it needs to be
charged and activated again to start the discharge.
WARNINGS:
- Do not put the powerbank in places with overheating temperatures (such as an airtight car that is under great sunlight heating, radiators, stoves, fires, and any other place which produces high temperatures). Overheating can damage the powerbank and in extreme cases can cause any potential threat to your own safety.
- The powerbank consists of sophisticated electronic components. To avoid accidentally hurting yourself or damaging the powerbank, it is advised to not disassemble the powerbank yourself.
- There are Li-Polymer batteries inside the powerbank. Please pay attention to the recycling regulations, as they can not be discarded.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>