PAWFiT 3S GPS Pet Tracker User Manual
- June 3, 2024
- PAWFiT
Table of Contents
PAWFiT 3S GPS Pet Tracker User Manual
SAFETY INFORMATION
Pawfit 3s is specifically designed and optimised for tracking dogs and cats. It is the sole responsibility of the owner and user to abide by the law and rules in areas the Pawfit 3s is used.
Electromagnetic compatibility
Please avoid exposing your Pawfit 3s to strong magnetic fields as they may potentially damage your tracker or cause it to malfunction.
Battery
- Pawfit 3s uses rechargeable lithium-ion polymer battery.
- The battery cannot be replaced or removed.
- Do not charge your Pawfit 3s with a power source greater than 5V and 2.1 A.
- Keep Pawfit 3s away from flammable objects and materials.
- Do not charge Pawfit 3s near a heat source or in direct sunlight.
- Do not charge Pawfit 3s while it is wet.
- Do not short circuit the positive and negative terminals of the charging pins.
- Never leave Pawfit 3s unattended whilst charging.
- If Pawfit 3s is damaged, it should be repaired or disposed of immediately.
- Do not use a fast-charging source to charge your Pawfit 3s.
- If Pawfit 3s starts to smoke, catch fire and deforms during charging, immediately turn off the power, remove the tracker from the charger and do not use it again.
- Recycle your Pawfit 3s correctly, never throw them in the bin.
- The operating temperature of Pawfit 3s is -10 °C to +50°C (14 to +122 °F).
Disregarding the above safety instructions can cause damage and possibly even
cause the battery to explode.
Failure to adhere to this safety information could result in the warranty
being made void.
IN THE BOX
GET STARTED
- Place Pawflt 3s Into the charging dock, and connect It to a power supply.
TIP: The LED turn RED while Pawfit is charging. Once fully charged the LED will turn GREEN. A full charge around 2.5 hours.
*Please use a quality USB Charger with an Output of 5V, no greater than 2.1A. - Switch on Pawflt 3s by pressing and holding the power button for 3 seconds.
TIP: Upon release of the power button, the tracker should came on with a steady blue light along with the start up sound ‘Welcome to Postal. After that the light will go off and the tracker will start searching for a network connection and this process can lake up to a minute.
- Download and install the Pawfit App.
The In-App Instructions will guide you through activating your tracker. A
subscription plan is required to activate your Pawfit 3s tracker.
- Place your pet’s collar between the collar strap and the collar attachment.
Tip: Secure the collar attachment on the collar by latching It onto both aides of the collar strap. For better signal reception, please position the tracker on your pees back
Disposal
Batteries are considered household hazardous waste and should be disposed of properly at a hazardous waste collection site. Alternatively, you could contact Pawfit for recycling options.
CARE TIPS
- Ensure your Pawfit 3s is 100% dry, especially the copper plates before charging it.
- Use a quality USB charger with an output of 5V no greater than 2.1A.
- If Pawfit 3s gets dirty, rinse it in clean water, no soap, check the speaker for water/dirt and leave to dry completely.
- Keep Pawfit 3s out of your pet’s mouth to prevent damage to the waterproof casing.
- Always rinse Pawfit 3s in fresh water after a sea swim.
- Regularly check your Pawfit 3s for any signs of wear and tear, especially the collar strap. You can visit the Pawfit website to purchase additional accessories.
WARRANTY
Limited to 18-month warranty.
Please contact local distributors or visit Pawfit website
www.pawfit.com for more information.
DECLARATION OF CONFORMITY
Latsen Technology Ltd. declares that the Pawfit 3s tracker comply with Part 15 of the FCC Rules, the fundamental requirements and other relevant provisions of directive 2014/53/EU, and Industry Canada license-exempt RSS standard(s). Please visit pawfit.com/legal for the full text of our declaration of conformity.
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receivingantenna.
- Increase the separation between the equipment andreceiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Any changes or modifications to this device not explicitly
approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Radiation Exposure Statement
To comply with FCC RF exposure compliance requirements, this grant is
applicable to only mobile configurations. The antennas used for this
transmitter must be installed to provide a separation distance of at least 20
cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
ISED Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference.
- This device must accept any interference, including interference that may cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES‐3 (B)/NMB‐3(B).
Radiation Exposure Statement
To comply with FCC RF exposure compliance requirements, this grant is
applicable to only mobile configurations. The antennas used for this
transmitter must be installed to provide a separation distance of at least 20
cm from all persons and must not be co-located or operating in conjunction
with any other antenna or transmitter.
CUSTOMER SUPPORT
You can find a comprehensive FAQ and troubleshooting guide on the Pawfit
website at https://support.pawfit.com
If you have a question and want to contact us, please email us at
support@pawfit.com. Our dedicated support team
will get back to you ASAP.