StrikeMaster SM Lite Flite NDA3 Flange Instruction Manual

October 30, 2023
StrikeMaster

StrikeMaster logo

StrikeMaster SM Lite Flite NDA3 Flange

StrikeMaster SM Lite Flite NDA3 Flange-product

Product Information: NDA-3 Drill Adapter & FND Safety Flange Assembly

The NDA-3 Drill Adapter & FND Safety Flange Assembly is a tool used for drilling ice. The adapter is inserted into the center of the FND flange and then pushed into the collar of the drill unit. The flange and adapter are connected to the drill unit using the collar bolt and hex wrench. The assembly is compatible with cordless drivers and Lite-Flite LazerTM drill units.

Safety Instructions

  • Always keep hands, feet, hair and loose clothing away from the rotating auger to prevent injury.
  • Check blade screws before each use as cutting blades are sharp and should be kept away from the body.

Product Usage Instructions

How to Attach the NDA-3 Drill Adapter to the Cordless Driver
  1. Do NOT lock your grip with your thumb around the handle.
  2. Open the chuck with your hands.
  3. Push the adapter into the open chuck.
  4. Tighten the chuck onto the adapter by lining up the chuck teeth with the flat on both sides of the adapter. Do NOT use the trigger to tighten the chuck.
  5. Do NOT use the trigger or wear gloves while tightening the chuck, as this may cause serious injury.
How to Operate the Cordless Driver with the Lite-Flite LazerTM Drill

Unit

  • Use the lowest speed setting on the cordless driver.
  • DO NOT use the cordless driver’s hammer or impact function.
  • Always place your thumb on top of the side-handle.
  • DO NOT drill ice without holding the side-handle on the cordless driver.
  • DO NOT lock your grip with your thumb around the side-handle.
  • DO NOT drill with only one hand.
  • DO NOT hold the ice drill unit, flange or drill chuck while drilling ice.

STRIKEMASTER® LITE-FLITE LAZER™ DRILL UNIT, THE NDA-3 DRILL ADAPTER & FND SAFETY FLANGE

ASSEMBLY AND SAFE USE INSTRUCTIONS

  • Place the NDA-3 adapter into the center of the FND flange.
  • Push the adapter in firmly until it locks into the flange.
  • Push the flange with adapter into the collar of the drill unit. Connect flange and adapter to drill unit, using collar bolt and hex wrench.
  • Insert bolt into the top hole on the non-threaded side of the collar.StrikeMaster SM Lite Flite NDA3 Flange-fig-1

SAFE USE OF CORDLESS DRIVER AND LITE-FLITE LAZER™ DRILL UNIT
HOW TO ATTACH THE SIDE HANDLE AND USE THE CORRECT GRIP.

  • Attach the side handle to the drill unit. Always securely hold the side-handle when drilling ice.
  • Always place your thumb on top of the side-handle.
  • DO NOT lock your grip with your thumb around the handle.StrikeMaster SM Lite Flite NDA3 Flange-fig-2
HOW TO ATTACH THE NDA-3 DRILL ADAPTER TO THE CORDLESS DRIVER
  • Open the chuck with your hands. DO NOT use trigger to rotate the chuck.
  • Push the adapter into the open chuck. Line up the chuck teeth with the flat sides of the adapter.
  • Tighten the chuck on to the adapter by hand. DO NOT use the trigger to tighten the chuck.
  • DO NOT use the trigger or wear gloves while tightening the chuck, may cause serious injury.StrikeMaster SM Lite Flite NDA3 Flange-fig-3
HOW TO OPERATE THE CORDLESS DRIVER WITH THE LITE-FLITE LAZER™ DRILL UNIT
  • Use the lowest speed setting on the cordless driver.
  • DO NOT use the cordless driver’s hammer or impact function.
  • Always place your thumb on top of the side-handle.
  • DO NOT lock your grip with your thumb around the side-handle.
  • DO NOT drill ice without holding the side-handle on the cordless driver.StrikeMaster SM Lite Flite NDA3 Flange-fig-4

DO NOT drill with only one hand. DO NOT hold the ice drill unit, flange or drill chuck while drilling ice.StrikeMaster SM Lite Flite NDA3 Flange-
fig-5

WARNING
Always keep hands, feet, hair and loose clothing away from the rotating auger. Failure to do so may cause serious injury.

CAUTION
Check blade screws before each use. Cutting blades are sharp, keep away from body.

Suite 100, 935 Aldrin Drive, Eagan, MN 55121
USA customer service email: strikemaster@rapalausa.com
TOLL-FREE HELPLINE: 1-877-572-7278
(Monday – Friday / 8am – 4:30pm CST)
www.strikemaster.com
1350 Phillip Murray Ave,
Oshawa, ON L1J 6Z9, Canada
cacustserv@rapalavmc.com
TOLL-FREE HELPLINE: 905-571-3001
(Monday – Friday / 8am – 4:30pm ET)
www.strikemaster.ca
©2021 StrikeMaster, Inc. 0822

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals