spirograaf 33982 Travel Spirograph Carpet Set User Guide
- June 5, 2024
- spirograaf
Table of Contents
spirograaf 33982 Travel Spirograph Carpet
Set
INTRODUCTION
2 Pens
6 Wheels
Travel Spirograph
- Paper may be reflled with standard 3in x 3in (7.6cm x 7.6cm) sticky note paper.
- Spirograph pen inks have been evaluated and approved by a board certified toxicologist.
- Inks may stain some surfaces and fabrics.
- The Spirograph pieces have been to accommodate most types of pens found in the market. We recommend using pens with a point size of 1mm or smaller.
HASBRO and its logo, SPIROGRAPR trademarks of Hasbro and are used with permission. 2021 Hasbro.
Basic Pattern Guide
These boxes show the basic pattern produced by each of the different WHEELS.
The patterns here were all drawn with the pen in Hole No. 1 of each WHEEL.
The number of teeth on a WHEEL and RING determines the number of points in the
pattern. For each numbered hole on a WHEEL, the shape of the pattern changes,
but the number of points in the pattern stays the same.
WHEEL used to create pattern.
Number of points in pattern.
Using Travel Spirograph
- Slide the frame all the way open and place a sheet of paper on the base, sticky side down.
- Close the frame over the sheet of paper. The frame will lock shut with a click.
- Place a WHEEL inside the RING and engage the teeth of both pieces so they interlock.
NOTE: When using your pens for the first time, scribble a little on a piece of scrap paper to get the ink flowing.
Always keep the pen in an upright position and keep the WHEEL teeth in contact with the RING teeth while drawing. Draw slowly to avoid slipping of the gears.
Positioning Lines
Using the POSITIONING LINES to begin your design at different starting points
along the RiING, you can create more complex patterns. The design below uses
HOLE No. 1 on WHEEL No. 60, using a different color pen for each different
starting position.
HOLE No 1 in Starting Position on the RING
HOLE No. 1 in Starting Position No. 2 on the RING
Spirograph Designs
Place the QUAD WHEEL So that Hole I lines up with POSITIONING LINE No. I on the RING. With the Blue Pen in Hole l, draw a pattern until the line meets where it began. Ihen place the wheel so that Hole 1 line up with POSITIONING LINE No. 2 and draw a pattern with the Red Pen in Hole 1. Align Hole 1 with POSITIONING LINE No. 3 and draw one more pattern with the Red Pen in Hole 1. Align Hole 3 with POSITIONING LINE No. 1 and draw a pattern with the Blue Pen in Hole 3.
Place WHEEl No. 40 so that Hole 1 lines up with POSITIONING LINE No. 1 on the RING. With the Red Pen in Hole 1, draw a pattern until the line meets where it began. Align Hole with the spof where the last pattern ended and move the WHEEl one tooth to the right on the RING. Use the Red Pen in Hole l to draw a pattern. Repeat these steps to draw two more patterns with the Blue Pen in Hole 1, shitting one tooth to the right for each pattern.
HOLES 11-30
Place WHEEL No. 52 so that Hole 16 lines up with POSITIONING LINE No. I on the RING With the Blue Pen in Hole 16, draw a pattern until the line meers where it began. Place WHEEL No. 80 so that Hole 11 lines up with POSITIONING INE No. 1 on the RING. Draw a pattern with the Red Pen in Hole l11. Place WHEEL No. 80 so that Hole 30 lines up with POSITIONING LINE No. I on the RING. Draw a pattern with the Red Pen in Hole 30.
HOLES:5
Place WHEEL No. 60 so that Hole 5 lines up with POSITIONING LINE No. on the RlNG. With the Blue Pen in Hole 5, draw a pattern until the line meets where it begon. Align Hole 9 with POSITIONING LINE No. 1 and use the Blue Pen in Hole 9 to draw a pattern. Place the OVAL WHEEL so that Hole 3 lines up with POSITIONING LINE No. 2 on the RING. Draw a paftern with the Red Pen in Hole 5.
Visit www.Spirograph.com for more design ideas!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>