cybex 519003143 CLOUD Z i-SIZE Infant Car Seat User Guide

June 5, 2024
CYBEX

Cybex 519003143 CLOUD Z i-SIZE Infant Car Seat

OVERVIEW

cybex-519003143-CLOUD Z i-SIZE-Infant-Car-
Seat-5 cybex-519003143-CLOUD Z i-SIZE-Infant-Car-Seat-6 cybex-519003143-CLOUD Z i-SIZE-Infant-Car-Seat-13 cybex-519003143-CLOUD Z i-SIZE-Infant-Car-Seat-14IMPORTANT INFORMATION AND WARNINGS

  • Without the approval of the Type Approval Authority, the car seat may not be modified or added to in any way.
  • In order to keep your child properly protected, it is absolutely essential that you use the car seat as described in this User guide.
  • This car seat may only be installed on vehicle seats which are approved for the use of child restraint systems according to the vehicle manual.
  • The car seat can either be attached with the Base Z/Base Z One and ISOFIX, or with a 3-point automatic belt that is approved according to UN regulation No. 16 or an equivalent standard.
  • If the car seat is installed using a 3-point automatic belt, the vehicle belt buckle must never reach in the lap belt guide of the car seat. If the belt whip is too long, the car seat is not suitable for use in this position in the vehicle.
  • The installation of this car seat on the front passenger seat with the front airbag activated is NOT PERMITTED.
  • Do not use any load-bearing contact points other than those described in the User guide and marked on the child restraint.
  • The Newborn inlay is used to protect your child and must be used up until they have reached a height of 60 cm.
  • Before each journey make sure that the car seat harness system is correctly adjusted and fits tightly to the child’s body. The belts must never be twisted!
  • Always buckle up your child when it is in the car seat.
  • Only an optimally adjusted headrest can offer your child maximum protection and comfort while ensuring that the belt system can be fitted appropriately.
  • The car seat must always be correctly installed and secured in the vehicle even when not in use.
  • The load leg must always make direct contact with the floor of the vehicle. If your vehicle has storage compartments in the footwell, be sure to contact the vehicle manufacturer.
  • While driving, the car seat must always be locked in the rear-facing position.
  • For the car seat to provide the best possible protection, always use the linear side-impact protection (L.S.P.).
  • If using the car seat on a middle seat of the vehicle, the linear side-impact protection (L.S.P.) must never be folded out.
  • The car seat has also been tested and approved for use without the linear side-impact protection (L.S.P) folded out.
  • Always ensure that the car seat is not jammed against any surface when closing the vehicle door or adjusting the back seat.
  • Luggage or any other objects present in the vehicle must always be firmly secured. Otherwise, they may be thrown within the vehicle, which could cause fatal injuries.
  • The car seat must never be used without the seat cover. Ensure that only an original CYBEX seat cover is used, as the cover is a key element allowing the seat to function correctly.
  • Never leave your child unattended in the vehicle.
  • The lie-flat position may only be used outside the vehicle.
  • Do not place the car seats on raised surfaces, such as a table.
  • Parts of this child restraint system can heat up when exposed to direct sunlight and could potentially burn your child’s skin. Protect your child and the car seat from direct sun exposure.
  • An accident may cause damage to the car seat that is not identifiable with the naked eye. Please replace the car seat after an accident. In case of doubt, please consult your dealer or the manufacturer.
  • Do not use this car seat for more than 8 years. The car seat is exposed to high stress during its product lifespan, which leads to changes in the quality of its materials with increasing age.
  • The plastic parts can be cleaned with a mild cleaning agent and warm water. Never use harsh cleaning agents or bleaches!
  • On some vehicle seats made of sensitive materials, the use of car seats may leave marks and/or cause discolouration. To prevent this, you can place a blanket, towel or similar underneath the car seat to protect the vehicle seat.

PRODUCT PARTS

  1. Battery compartment
  2. Base
  3. Load leg
  4. Newborn inlay
  5. ISOFIX-Release buttons
  6. ISOFIX-Locking arms
  7. ISOFIX-Anchorage points
  8. ISOFIX-Indicators
  9. Load leg adjustment button
  10. Load leg indicator
  11. Carrying handle
  12. Carrying handle release buttons
  13. Seat locking indicator
  14. Linear side-impact protection
  15. (L.S.P.)
  16. Tilt angle indicator
  17. 3-point automatic belt
  18. Lap belt guide
  19. Diagonal belt guide
  20. Green seat release button
  21. Upper seat release button
  22. Load leg parking position
  23. Headrest
  24. Headrest adjustment handle
  25. Belt adjustment button
  26. Shoulder belt
  27. Belt buckle
  28. Buckle tongue
  29. Central adjustment belt
  30. Green button
  31. Seat rotation slider
  32. Driving direction indicator
  33. Sun canopy
  34. The release handle for a lie-flat position
  35. Release button for stroller adapter
  36. User guide compartment

PREPARING TO INSTALL THE BASE Z

Before using the base for the first time, the plastic strip must be removed from the Battery compartment (1) on the load leg. The Base (2) will emit an audible warning signal until it has been correctly installed. If the Load leg (3) is folded out and there is no sound, the battery must be checked. To check the battery, the Battery compartment (1) on the back of the load leg can be opened with a screwdriver. The battery may only be replaced with a CR2032 size battery.

DIFFERENT USES OF THE SEAT

The Newborn inlay (4) integrated at purchase should be removed if your child is taller than 60 cm. To remove the Newborn inlay (4) open the belt buckle, pull off the shoulder pads and then remove the inlay.

THE CORRECT POSITION IN THE VEHICLE

This is an i-Size Enhanced Child Restraint System. It is approved according
to UN Regulation No. R129/02, for use in i-Size compatible vehicle seating positions as indicated by vehicle manufacturers in their vehicle user manuals. If your vehicle does not have an i-Size seating position, please check the enclosed vehicle Type List. You can obtain the most up-to-date version of the Type List from www.cybex-online.com.
Alternatively, the car seat may be installed on forward-facing vehicle seats equipped with a 3-point automatic belt system in accordance with UN R16.

INSTALLATION IN THE VEHICLE

Always ensure that…

  • the backrests in the vehicle are locked in their upright position.
  • when installing the child seat on the front passenger seat, adjust the vehicle seat as far back as possible.

Installation of the car seat with base

  1. Fold-out the Load leg (3) until it locks into its foremost position. If you use the Base Z, an acoustic warning signal will sound until the load leg has been correctly installed.
  2. Release the ISOFIX-Release buttons (5) to extend the ISOFIX-Locking arms (6).
  3. The ISOFIX-Release buttons can both be released independently allowing the theISOFIX-Locking arms to be adjusted independently.
  4. Push the ISOFIX-Locking arms (6) out of the base to their furthest extent.
  5. Place the base (2) on an appropriate seat in the vehicle.
  6. Push the ISOFIX-Locking arms (6) into the ISOFIX-Anchorage points (7) until these lock into place with an audible “CLICK”. The two ISOFIX Indicators (8) will switch from RED to GREEN.
  7. Ensure the base is secure by trying to pull it out of the ISOFIX-Anchorage points (7).
  8. Push the Base (2) towards the backrest of the vehicle seat until it is fully aligned with the backrest.
  9. Moving the base from side to side will also brace it against the vehicle
  10. Press the Load leg adjustment button (9) and extend the leg until it touches the vehicle floor.
  11. Pull the Load leg (3) out to the next locking position to ensure optimal force transmission.
  12. The Load leg indicator (10) switches to GREEN when the load leg is correctly positioned on the vehicle floor. When using the Base Z, the acoustic warning signal will also stop.
  13. Move the Carrying handle (11) to position A. Therefor, press the two Carrying Handle release buttons on the left and right of the Carrying handle (12) at the same time.
  14. Place the car seat on the Base (2).
  15. When used with Base Z, the car seat can also be locked in its entry position on the base. Then turn the car seat until it is aligned opposite to the direction of travel.
  16. Please ensure that the car seat locks into place with an audible “CLICK”.
  17. Check whether the Seat locking indicator (13) on the base is GREEN.
  18. In order to achieve the best possible protection, activate the Linear side impact protection (L.S.P) (14) on the side of the car seat facing the vehicle door by pulling on it’s end.
  19. The car seat can also be used with the L.S.P. folded in if there is not enough space in the vehicle. To do this, fold in the element back to its starting position.

Installing the car seat with 3-point automatic belt

  1. Place the car seat on the vehicle seat against the direction of travel.
  2. Make sure that the Carrying handle (11) is locked in position A.
  3. Make sure that the Level angle indicator (15) is parallel with the vehicle floor.
  4. Pull out the 3-point automatic belt (16) and place its lap section into the lap belt guide (17).
  5. Lock the 3-point automatic belt (16) of the vehicle in its belt buckle.
  6. Tighten the lap section by pulling the diagonal section in the direction of travel.
  7. Guide the diagonal section of the belt behind the head end of the car seat and through the diagonal belt guide (18) and above the Linear side-impact protection (L.S.P) (14).
  8. In order to achieve the best possible protection, activate the Linear side impact protection (L.S.P) (14) on the side of the car seat facing the vehicle door by pulling on its end.

The car seat can also be used with the L.S.P. folded in if there is not enoughspace in the vehicle. To do this, fold in the element back to its starting position.

REMOVAL FROM THE VEHICLE

Removal of the car seat with base

  1. To unlock the car seat from the base, push the Green seat release button (19) and pull the Upper seat release button (20) up at the same time.
  2. Tilt the car seat slightly and lift it off the base.
  3. Unlock the ISOFIX-Locking arms (6) on both sides by pressing the ISOFIX-Release buttons (5) and at the same time pulling them back.
  4. Pull out the Base (2) from the ISOFIX-Anchorage points (7).
  5. Remove the Base (2) and slide the ISOFIX-Locking arms (6) completely back into their transport positions.
  6. Push the Load leg (3) back into its original position and then fold it in to save space.
  7. If you are using the Base Z, it is important to fully fold in the load leg so that the acoustic warning is muted. There is a Load leg parking position (21) indicated on the underside of the base.

Removal of the car seat with 3-point automatic belt

  1. Take the diagonal section of the belt out of the diagonal belt guide (18).
  2. Unlock the vehicle seat belt buckle and take the lap section of the belt out from the lap belt guides (17).

ADJUSTING THE HEADREST

The adjustable Headrest (22) can be adjusted by using the Headrest adjustment handle (23). When adjusting the Headrest (22) ensure that no more than 2 cm (approx. 2 finger’s width) remain between the child’s shoulders and the headrest.

SECURING THE CHILD

  1. Press the Belt adjustment button (24) and pull both Shoulder belts (25) at the same time to loosen them.
  2. Undo the Belt buckle (26) by pressing the red button firmly.
  3. Put your child in the car seat with their buttocks at the back.
  4. Place the Shoulder belts (25) directly over your child’s shoulders.
  5. Place both Buckle tongues (27) together and lock them in place in the Belt buckle (26). You should hear an audible “CLICK”.
  6. If you are using a seat with a SensorSafe Clip, push the clip closed until you hear an audible “CLICK” and slide the closed clip down towards the Belt buckle (26).
  7. Pull on the Central adjustment belt (28) to tighten the Shoulder belts (25) until they rest snug against your child’s body.
  8. The harness should be fitted tight enough so that it is not possible to put a foldin any of the straps.
  9. When using the SensorSafe clip, position the clip directly below the shoulder pads.

ROTATION FUNCTION

The rotation function is only available in combination with the Base Z. Push the Green button (29) on the Seat rotation slider (30) to the side and then pull the entire slider outwards. Now you can turn the seat.
Before starting your journey, make sure that the car seat is properly locked into place and the Driving direction indicator (31) shows GREEN.

ADJUSTING THE SUN CANOPY

Unfold the Sun canopy (32) by pulling on the plastic cover.

ADJUSTING THE LYING POSITION OUTSIDE THE VEHICLE

The car seat can be brought into the lie-flat position by pressing the release handle for the lie-flat position (33) while simultaneously shifting the back section downwards.

TRAVEL SYSTEM

You can attach the car seat to any approved stroller. Click the car seat onto the approved adapter, facing the parent. To unlock, hold down the two Release buttons for the stroller adapter (34) and lift them up.

REMOVING AND REATTACHING THE SEAT COVER

The car seat cover consists of 6 parts. These are fastened to the car seat at several places. Once unfastened, the individual parts of the cover can be removed. To reattach the cover, follow the removal instructions in the reverse order.

The cover may only be washed at 30°C with a delicate wash program otherwise it may result in discoloration of the cover fabric. Please wash the cover separately from other laundry and do not dry it in the dryer or in direct sunlight!

MANUFACTURER’S WARRANTY AND DISPOSAL REGULATION

CYBEX GmbH (Riedingerstr. 18, 95448 Bayreuth, Germany) gives you 3 years warranty on this product. The warranty is valid in the country where this product was initially sold by a retailer to a customer. The contents of the warranty and all essential information required for the assertion of the warranty can be found on our homepage: go.cybex-online.com/manufacturer- warranty-car-seats. If a warranty is shown in the article description, your legal rights against us for defects remain unaffected.Please observe the waste disposal regulations in your country.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals