milwaukee M18 BH Compact Sds Hammer User Manual
- June 5, 2024
- Milwaukee
Table of Contents
milwaukee M18 BH Compact Sds Hammer
TECHNICAL DATA
Battery voltage 18 V
No-load speed 0-1300 min-1
Rate of percussion under load max. 0-7000 min-1
Impact energy per stroke accordng to EPTA-Procedure 05/2009 1.2 J
Drilling capacity in concrete 16 mm
Drilling capacity in steel 10 mm
Drilling capacity in wood 16 mm
Check neck diameter 43 mm
Weight according EPTA-Procedure 01/2003 (Li-Ion 4.0 Ah) 2.5 kg
Noise/vibration information
Measured values determined according to EN 60745.
Typically, the A-weighted noise levels of the tool are:
Sound pressure level (K = 3 dB(A)) 87.9 dB(A)
Sound power level (K = 3 dB(A)) 98.9 dB(A)
Wear ear protectors!
Total vibration values (vector sum in the three axes) determined according
to EN 60745.
Vibration emission value ah
Hammer-drilling in concrete 10.3 m/s2
Uncertainty K 1.5 m/s2
WARNING! Read all safety warnings and all instructions. Failure to follow
the warnings and instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future reference.
SAFETY INSTRUCTIONS
Hammer safety warnings
Wear ear protectors. Exposure to noise can cause hearing loss.
Use auxiliary handle(s), if supplied with the tool. Loss of control can cause
personal injury.
Hold power tool by insulated gripping surfaces, when performing an operation
where the cutting accessory may contact hidden wiring. Cutting accessory
contacting a “live” wire may make exposed metal parts of the power tool “live”
and could give the operator an electric shock.
Always wear goggles when using the machine. It is recommended to wear gloves,
sturdy non slipping shoes and apron.
The dust produced when using this tool may be harmful to health. Do not inhale
the dust. Wear a suitable dust protection mask.
Sawdust and splinters must not be removed while the machine is running.
When working in walls ceiling, or fl oor, take care to avoid electric cables
and gas or waterpipes.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning
them. Milwaukee Distributors offer to retrieve old batteries to protect our
environment.
Do not store the battery pack together with metal objects (short circuit
risk).
Use only System C18 chargers for charging System C18 battery packs. Do not use
battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep
dry at all times.
Battery acid may leak from damaged batteries under extreme load or extreme
temperatures. In case of contact with battery acid wash it off immediately
with soap and water. In case of eye contact rinse thoroughly for at least 10
minutes and immediately seek medical attention.
No metal parts must be allowed to enter the battery section of the charger
(short circuit risk).
SPECIFIED CONDITIONS OF USE
The battery rotary pneumatic hammer can be used for hammer drilling and
drilling in wood, metal as well as plastic for independent use away from mains
supply.
Do not use this product in any other way as stated for normal use.
BATTERIES
New battery packs reach full loading capacity after 4-5 chargings and
dischargings. Battery packs which have not been used for some time should be
recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery
pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, the battery packs have to be fully charged, after
use.
To obtain the longest possible battery life remove the battery pack from the
charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from
moisture
Store the battery packs in a 30%-50% charged condition.
Every six months of storage, charge the pack as normal.
How to Use
The ventilation slots of the machine must be kept clear at all times.
Important note! If the carbon brushes are worn, in addition to exchanging the
brushes the tool should be sent to after-sales service. This will ensure long
service life and top performance
Use only Milwaukee accessories and Milwaukee spare parts. Should components
need to be replaced which have not been described, please contact one of our
Milwaukee service centers.
If needed, an exploded view of the tool can be ordered. Please state the
machine type printed as well as the six-digit No. on the label and order the
drawing at your local service agents.
SYMBOLS
Please read the instructions carefully before starting the machine.
CAUTION! WARNING! DANGER!
Remove the battery pack before starting any work on the machine.
Accessory – Not included in standard equipment, available as an accessory.
Do not dispose of electric tools together with household waste material! In
observance of European Directive 2002/96/EC on waste electrical and electronic
equipment and its implementation in accordance with national law, electric
tools that have reached the end of their life must be collected separately and
returned to an environmentally compatible recycling facility.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>