milwaukee IPWE 400 R-RQC 1-2 Inch Drive Impact Wrench User Manual

milwaukee IPWE 400 R-RQC 1-2 Inch Drive Impact Wrench

TECHNICAL DATA IPWE 400 R IPWE 520 R

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.

IMPACT DRIVER SAFETY WARNINGS

Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Wear ear protectors. Exposure to noise can cause hearing loss.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS
Use protective equipment. Always wear safety glasses when working with the machine.
The use of protective clothing, such as dust mask, protective gloves, sturdy non-slipfootwear, helmet and ear defenders, is recommended.
The dust produced when using the product may pose a health hazard. Do not inhal e the dust. Wear a suitable dust protection mask.
Do not operate on materials (e.g. asbestos) that present a health hazard.
Switch off the product immediately if the insertion tool stalls. Do not switch on the product again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the insertion tool stalled and rectify this, paying heed to the safety instructions.

The possible causes may be:

• it is tilted in the workpiece;

• it has pierced the workpiece;

• the product is overloaded.
  Do not reach into the product while it is running.
  The insertion tool may become hot during use.
  WARNING!
  Danger of burns:

• when changing tools

• when setting the device down

Chips and splinters must not be removed while the machine is running.
Keep mains lead clear from working range of the machine. Always lead the cable away behind you.
When working in walls ceiling, or fl oor, take care to avoid electric cables and gas or waterpipes.
Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.
Always disconnect the plug from the socket before carrying out any work on the product.

SPECIFIED CONDITIONS OF USE
The impact wrench can be used to tighten and loosen nuts and bolts.
Do not use the product in any way other than as stated for normal use.

MAINS CONNECTION

Connect only to single-phase AC system voltage as indicated on the rating plate. It is also possible to connect to sockets without an earthing contact as the design conforms to safety class II.
Appliances used at many diff erent locations, including wet room and open-air, must be connected via a residual current device (FI, RCD, PRCD) of 30 mA or less.
Make sure the product is switched off before plugging in.
Under the eff ect of extreme electromagnetic interferences from the outside, temporary variations in the speed of rotation could arise in particular cases.

HOW TO USE

MAINTENANCE

The ventilation slots of the machine must be kept clear at all times.
If the supply cord of the product is damaged, it must only be replaced by a repair shop appointed by the manufacturer, to avoid hazardous situations.
Important note! If the carbon brushes are worn, in addition to exchanging the brushes, the tool should be sent to after-sales service. This will ensure long service life and top performance.
Use only Milwaukee accessories and Milwaukee spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the Article No. as well as the machine type printed on the label and order the drawing at your local service agents.

SYMBOLS

CAUTION! WARNING! DANGER!
Always disconnect the plug from the socket before carrying out any work on the product..
Please read the instructions carefully before starting the product.
Do not dispose of electric tools together with household waste material. Electric tools and electronic equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. Check with your local authority or retailer for recycling advice and collection point.
Class II construction, tool in which protection against electric shock does not rely on basic insulation only, but in which additional safety precautions, such as double insulation or reinforced insulation, are provided.
Wear eye protection

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>