Lenco SCD-430RD Portable Radio Cd Mp3 Cassette Player User Manual

: June 5, 2024
: Lenco

Model: SCD-430RD

USER MANUAL PORTABLE RADIO, CD MP3, CASSETTE PLAYER

SCD-430RD

CAUTION:
Usage of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.

PRECAUTIONS BEFORE USE

KEEP THESE INSTRUCTIONS IN MIND:

Do not cover or block any ventilation openings. When placing the device on a shelf, leave 5 cm (2″) free space around the whole device.
Install in accordance with the supplied user manual.
Keep the device away from heat sources such as radiators, heaters, stoves, candles and other heat-generating products or naked flame. The apparatus can only be used in moderate climates. Extremely cold or warm environments should be avoided. Working temperature between 0° and 35° C.
Avoid using the device near strong magnetic fields.
Electrostatic discharge can disturb normal usage of this device. If so, simply reset and restart the device following the instruction manual. During file transmission, please handle with care and operate in a static-free environment.
Warning! Never insert an object into the product through the vents or openings. High voltage flows through the product and inserting an object can cause electric shock and/or short circuit internal parts. For the same reason, do not spill water or liquid on the product.
Do not use in wet or moist areas such as bathrooms, steamy kitchens or near swimming pools.
The apparatus shall not be exposed to dripping or splashing and make sure that no objects filled with liquids, such as vases, are placed on or near the apparatus.
Do not use this device when condensation may occur. When the unit is used in a warm wet room with damp, water droplets or condensation may occur inside the unit and the unit could maybe not work properly; let the unit stand in power OFF for 1 or 2 hours before turning on the power: the unit should be dry before getting any power.
Although this device is manufactured with the utmost care and checked several times before leaving the factory, it is still possible that problems may occur, as with all electrical appliances. If you notice smoke, an excessive build-up of heat or any other unexpected phenomena, you should disconnect the plug from the main power socket immediately.
This device must operate on a power source as specified on the specification label. If you are not sure of the type of power supply used in your home, consult your dealer or local power company.
Keep away from rodents. Rodents enjoy biting on power cords.
To clean the device, use a soft dry cloth. Do not use solvents or petrol based fluids. To remove severe stains, you may use a damp cloth with dilute detergent.
The supplier is not responsible for damage or lost data caused by malfunction, misuse, modification of the device or battery replacement.
Do not interrupt the connection when the device is formatting or transferring files. Otherwise, data may be corrupted or lost.
If the unit has USB playback function, the usb memory stick should be plugged into the unit directly. Don’t use an usb extension cable because it can cause interference resulting in failing of data.
The rating label has been marked on the bottom or back panel of the apparatus.
This device is not intended for use by people (including children) with physical, sensory or mental disabilities, or a lack of experience and knowledge, unless they’re under supervision or have received instructions about the correct use of the device by the person who is responsible for their safety.
This product is intended for non professional use only and not for commercial or industrial use.
Make sure the unit is adjusted to a stable position. Damage caused by using this product in an unstable position vibrations or shocks or by failure to follow any other warning or precaution contained within this user manual will not be covered by warranty.
Never remove the casing of this apparatus.
Never place this apparatus on other electrical equipment.
Do not allow children access to plastic bags.
Only use attachments/accessories specified by the manufacturer.
Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as the power supply cord or the plug, when liquid has been spilled or objects have fallen into the apparatus, when the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Prolonged exposure to loud sounds from personal music players may lead to temporary or permanent hearing loss.
If the product is delivered with power cable or AC power adaptor:
- If any trouble occur, disconnect the AC power card and refer servicing to qualified personnel.
- To completely disconnect the power input, the mains plug of the apparatus shall be disconnected from the mains, as the disconnect device is the mains plug of apparatus.
- Don’t step on or pinch the power adaptor. Be very careful, particularly near the plugs and the cable’s exit point. Do not place heavy items on the power adaptor, which may damage it. Keep the entire device out of children’s reach! When playing with the power cable, they can seriously injure themselves.
- Unplug this device during lightning storms or when unused for a long period.
- The socket outlet must be installed near the equipment and must be easily accessible.
- Do not overload ac outlets or extension cords. Overloading can cause fire or electric shock.
- Devices with class 1 construction should be connected to a main socket outlet with a protective earthed connection.
- Devices with class 2 construction do not require a earthed connection.
- Always hold the plug when pulling it out of the main supply socket. Do not pull the power cord. This can cause a short circuit.
- Do not use a damaged power cord or plug or a loose outlet. Doing so may result in fire or electric shock.
If the product contains or is delivered with a remote control containing coin/cell batteries:
Warning:
- “Do not ingest battery, Chemical Burn Hazard” or equivalent working.
- [The remote control supplied with] This product contains a coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
- Keep new and used batteries away from children.
- If the battery compartment does not close securely, stop using the product and keep it away from children.
- If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Caution about the use of Batteries:
- Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type.
- Battery cannot be subjected to high or low extreme temperatures, low air pressure at high altitude during use, storage or transportation.
- Replacement of a battery with an incorrect type that can result in an explosion or the leakage of flammable liquid or gas.
- Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
- Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or that leakage of flammable liquid or gas.
- A battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
- Attention should be drawn to the environmental aspects of battery disposal.

INSTALLATION

Unpack all parts and remove protective material.
Do not connect the unit to the mains before checking the mains voltage and before all other connections have been made.

Warning for CD/DVD player:

WARNING

Class 1 Laser Product

CLASS 1 LASER PRODUCT

CAUTION
INVISIBLE LASER RADIATION WHEN OPEN AND INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM

|
---|---|---
The product contains a low power laser device.

Warning: Do not touch the lens.

ACCESSORIES

Instruction Booklet

AC Cord

LOCATION OF CONTROLS

NAMES OF CONTROLS

CASSETTE PLAY KEY
CASSETTE REWIND KEY
CASSETTE FAST FORWARD KEY
CASSETTE STOP/EJECT KEY
CASSETTE PAUSE KEY
CD FOLD+/+10 BUTTON
CD FOLD-/-10 BUTTON
CD PROG./P-MODE BUTTON
BASS BUTTON
VOLUME CONTROL
FUNCTION SWITCH
FOLDING HANDLE
BAND SELECTOR
DIAL SCALE
TUNING CONTROL
CD COMPARTMENT
CD DOOR OPEN/CLOSE
CD SKIP/SEARCH FORWARD BUTTON
PLAY/PAUSE/STANDBY BUTTON
STOP BUTTON
CD SKIP/SEARCH BACKWARD BUTTON
SPEAKERS
FM STEREO INDICATOR
POWER INDICATOR
LCD DISPLAY
FM TELESCOPIC ANTENNA
CASSETTE COMPARTMENT
AUX IN JACK
BATTERY COMPARTMENT
AC SOCKET

POWER SOURCE
This unit is designed to be operated on AC/DC.

AC OPERATION
Plug the smaller end of AC power cord into AC jack on unit and the other bigger end into AC wall outlet. The batteries will be automatically disconnected.

DC OPERATION
Open the BATTERY COMPARTMENT DOOR. Install 6 pcs UM-1/D size batteries (not included) into compartment. Please follow correct polarities as indicated.

CAUTION

Remove batteries if they are flat or not being used for a long period of time.
Batteries contain chemical substances, so they should be disposed of properly.

BASIC FUNCTION

SWITCHING ON THE UNIT

Set the FUNCTION switch to CD/MP3/AUX or RADIO.
In CD/MP3/AUX position, when the unit is not providing the main function for 15 minutes, the unit will automatically switch into standby mode. Press the PLAY/PAUSE/ button to turn on the unit again.

REMARK:

Please note that low volume setting in the audio source may be recognized as “no audio signal”, this will affect the capability of signal detection from the device and can also originate an automatic switch into standby mode. If this happens please reactivate the audio signal transmission or increase the volume setting on the audio source player in order to resume playback.
Electrostatic Discharge hints - The unit may reset or may not reset to normal operation mode due to electrostatic discharge, just switch it off and reconnect again.

TO ADJUST VOLUME
Rotate the VOLUME CONTROL back and forth to increase and decrease volume.

BASS BOOST SYSTEM
The BASS BOOST BUTTON controls the bass of the unit. Bass sound is the lower frequency ranges of sound. The knob can be pushed to OFF or ON position. When the BASS BOOST is on, the unit boosts (increases) the sound output of the bass frequencies.

RADIO OPERATION

TUNING IN RADIO STATIONS

Slide the FUNCTION switch to select the desired wave band: AM/FM ST..
Tune to required station by rotating the TUNING KNOB.
Rotate the VOLUME CONTROL to comfortable volume level.
Extend the TELESCOPIC ANTENNA to its full length if you are listening to FM broadcasting. Gently move the unit back and forth to get the best reception when you are listening to AM program, or place the unit in an open place.
Note: The FM STEREO indicator will be on if you are receiving FM stereo program.
Turn off the radio by switching the FUNCTION switch to “TAPE/OFF” position

CASSETTE OPERATION

PLAYBACK OF CASSETTE
Be sure to tighten any slack tape in the cassette before use, using either a pencil or a ball-point pen, simply insert the pen or pencil into the center of spool and rotate to remove slackness. Depress the STOP/EJECT button to open the cassette door.
Insert the cassette into the compartment with the open end facing upwards and the full reel on the left hand side, push the cassette well down and close the door, be sure not to touch the tape surface, Set the FUNCTION switch to “TAPE” position and press the cassette PLAY button. To stop playback, press the STOP/EJECT button once. To release the cassette, press the STOP/EJECT button again.

AUTO STOP
When the tape reaches the end during playback, the built-in auto stop system will release the depressed play key.

CARE OF CASSETTE MECHANISM
Gently clean the tape head and pinch wheel/capstan assemblies after every 10 hours of using the unit. A range of cassette care products are available.

The erase head and play head and the surface of the pinch roller are delicate and must not be touched with metal objects such as screwdrivers. You may find it easier to clean the assembly by pressing the PLAY button to bright head and pinch roller into view. Be sure to press the STOP button after cleaning the mechanism.
Damage to the pinch wheel can occur if the unit is left in PLAY mode with the power switch off. Under no circumstances should you attempt to lubricate any part of the machine.

CD/MP3 OPERATION

LOADING A DISC

Set the FUNCTION switch to CD/MP3/AUX position.
Open the CD door.
Place an audio CD into the tray with the label side facing up.
Close the CD door.
The total number of tracks will appear on the display after several seconds.
To remove the CD, press to open CD compartment lid, grasp the CD by its edges, and carefully take it out.

Note:

To ensure good system performance, wait until the disc tray completely reads the disc before proceeding.
If no disc is loaded into the compartment, or the disc is placed upside down, the display will show N0d.

PLAYING A DISC

Discs for Playback
This system can playback all digital audio CD, MP3, WMA finalized digital audio CD-Recordable (CD-R) discs, finalized digital audio CD-Rewritable (CD- RW) discs and CD-DA format digital audio CD/CD-R/CD-RW discs.

Press the PLAY/PAUSE/ button to start playback.
The playback starts from track 1, the “ ” indicator is shown on the display.
To interrupt playback, press the PLAY/PAUSE/ button. The “ ” indicator and the current track will flash on the display.
To resume playback, press the PLAY/PAUSE/ button again.
To stop playback, press the STOP button, the total number of tracks appears on the display.

SELECTING A DESIRED TRACK/PASSAGE

To select a desired track

Press the CD SKIP FORWARD/BACKWARD button repeatedly in stop mode or during play until the desired track appears on the display.
Press the PLAY/PAUSE/ button to start play.

To search for a particular passage during playback (track scanning at high speed)
Press and hold the CD SKIP FORWARD/BACKWARD button to scan the current playing track at high speed until desired point passage, and then release the button. Playback will start again from this point.
To select a song which track number exceeds 10
To select a song/track which number exceeds 10, press the FOLD+/+10 or FOLD-/-10 button each time to skip forward/backward 10 tracks, then press the CD SKIP FORWARD/BACKWARD button to select desired track.
To select a desired folder (for MP3 disc only, if the MP3 disc contains more than one folder)
Press and hold the FOLD+/+10 or FOLD-/-10 button more than 1 second to skip next/previous folder. Until the desired folder number appears on the LCD display, then release the button.

PROGRAM TRACKS
Programming tracks of disc are possible when playback is stopped. Up to CD 20 tracks/MP3 99 tracks can be stored in the memory in any order.

In stop mode, press the PROG./P-MODE button, the “PROG” will flash and the P01 indicator will be on.
Press the CD SKIP/SEARCH FORWARD button to select the first desired track to be programmed.
Press the PROG./P-MODE button to enter. The display changes to show P02.
Repeat steps 2 & 3 to store other desired tracks until all tracks are programmed.
Press the PLAY/PAUSE/ button to start playback from the first programmed track.
Press the STOP button to stop program playback.

To Erase the Memory (Program)
To clear the program, you have two options:

Press the STOP button when the disc is stopped, or
Open the CD compartment lid, program will be erased.

REPEAT

To Repeat a Single Track

Press the PROG./P-MODE button once in play mode, “ ” will flash on the display. The current track will be played repeatedly until the STOP button is pressed
Press the PROG./P-MODE button once more to cancel.

To repeat all the Tracks

Press PROG./P-MODE button twice in play mode, “ ” shows steady on the display, all tracks on the disc will be played repeatedly until the STOP button is pressed.
To cancel repeat play, press the PROG./P-MODE button once more.

To repeat current Directory (for MP3 only)

Press PROG./P-MODE button twice in play mode, “ FOLD” shows steady on the display, the current directory will be played repeatedly until the STOP button is pressed.
Press the PROG./P-MODE button once to cancel.

RANDOM PLAY
Press the PROG./P-MODE button in play mode till the “RDM” shows steady on the display, the random play will start from next track automatically, until all tracks are played over and then stop. Press the PROG./P-MODE button once to cancel.

INTROSCAN PLAY (for CD disc only)
Press the PROG./P-MODE button in play mode till the “INTRO” shows steady on the display, the unit will start to play the first 10 seconds of music of each track, until all tracks are played over and then stop. Press the PROG./P-MODE button once to cancel.

AUX-IN OPERATION
This unit has provided special AUX-IN jack, through this jack other audio sources can be connected to this unit and be amplified.

Set the FUNCTION switch to CD/MP3/AUX position.
Connect the audio cable into the AUX-IN jack and the other end connects to the AUDIO OUT jack of the external audio source. The unit will change to AUX mode automatically.
Adjust the volume of the main unit to your desired level.
Press PLAY of the external audio source (e.g. MP3 player) to start playback.

COMPACT DISC MAINTENANCE

1. Always use a compact disc bearing the mark as shown.

2. Notes on handling discs

Removing the disc from its storage case and loading it.
Do not touch the reflective recorded surface.
Do not stick paper or write anything on the surface.
Do not bend the disc.

3. Storage

Store the disc in its case.
DO not expose discs to direct sunlight or high temperatures, high humidity or dusty places.

4. Cleaning a disc

Should the disc become soiled, wipe off dust, dirt and fingerprints with a soft cloth.
The disc should be cleaned from the center to the edge.

CORRECT INCORRECT

FROM THE CENTRE TO THE EDGE

Never use benzene, thinners, record cleaner fluid or anti-static spray.
Be sure to close the CD door, so the lens is not contaminated by dust.
Do not touch the lens.

SPECIFICATIONS

CD SECTION
Channels: 2 channels
Optical pick-up: 3 beams laser
Frequency Response: 100Hz – 16KHz

RADIO SECTION
Receiving Band: AM/FM
Tuning Range: AM: 540 – 1600 KHz FM: 87.5 – 108 MHz
Antenna: FM rod antenna, AM built-in ferrite bar
(YOUR EXACT TUNING RANGE CAN BE CHECKED FROM BACK PLATE OF UNIT)

GENERAL
Output Power: 1.5W x 2 (MAX)
Aux in jack: 3.5mm
Power Source: AC 230V ~ 50Hz DC 9V 1.5V UM-1/D x 6pcs
(YOUR EXACT AC POWER CAN BE CHECKED ON THE BACK PLATE OF UNIT)
Power Consumption: 15 W
Power Consumption (Standby): <0.5W

CASSETTE SECTION
Biasing System DC Bias
Frequency Response 125 – 6.3 KHz
Wow and Flutter 0.35 % WRMS (JIS)

Note: Specifications are subject to change for continuous improvement without prior notice.

Disclaimer
Updates to Firmware and/or hardware components are made regularly. Therefore some of the instruction, specifications and pictures in this documentation may differ slightly from your particular situation. All items described in this guide for illustration purposes only and may not apply to particular situation. No legal right or entitlements may be obtained from the description made in this manual.

Guarantee
Lenco offers service and warranty in accordance to European law, which means that in case of repairs (both during and after the warranty period) you should contact your local dealer.

Important note: It is not possible to send products that need repairs to Lenco directly.

Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires.

This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer will be voided.

Disposal of the Old Device
This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe. To ensure the correct waste treatment of the product and battery, please dispose them in accordance to any applicable local laws of requirement for disposal of electrical equipment or batteries. In so doing, you will help to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste (Waste Electrical and Electronic Equipment Directive).

CE Marking
Hereby, Lenco Benelux B.V., Thermiekstraat 1a, 6361 HB Nuth, The Netherlands, declares that this product is in compliance with the essential EU directive requirements.

The declaration of conformity may be consulted via
techdoc@commaxxgroup.com

Service
For more information and helpdesk support, please visit
www.lenco.com
Lenco Benelux BV, Thermiekstraat 1a, 6361 HB, The Netherlands.