RYOBI FP32220 18V 3/8 Inch Extended Reach Ratchet Owner’s Manual

RYOBI FP32220 18V 3/8 Inch Extended Reach Ratchet

SAFETY WARNINGS

• WORK AREA SAFETY

•  Keep work area clean and well lit. Cluttered or dark areas invite accidents.

•  Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

•  Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
  ELECTRICAL SAFETY

•  Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

•  Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

•  Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

•  Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord awayfrom heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

•  When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

•  If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter(GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.

•  Use this product only with batteries and chargers listed in tool/appliance/battery pack/charger correlation supplement 987000-432.
  PERSONAL SAFETY

•  Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.

•  Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, nonskid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

•  Prevent unintentional starting. Ensure the switch is inthe off-position before connecting to power source and/ or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.

•  Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

•  Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

•  Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.

•  If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

•  Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

•  Do not wear loose clothing or jewelry. Contain long hair. Loose clothes, jewelry, or long hair can be drawn into air vents.

•  Do not use on a ladder or unstable support. Stable footing on a solid surface enables better control of the power tool in unexpected situations.
  POWER TOOL USE AND CARE

•  Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

•  Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

•  Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

•  Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

•  Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

•  Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

•  Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

•  Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
  BATTERY TOOL USE AND CARE

•  Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

•  Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

•  When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.

•  Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

RATCHET

•  Hold power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
•  Wear ear protectors during operation. Exposure to noise can cause hearing loss.
•  Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
•  Know your power tool. Read operator’s manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this power tool. Following this rule will reduce the risk of electric shock, fire, or serious injury.
•  Always wear eye protection with side shields marked to comply with ANSI Z87.1 when assembling parts, operating the tool, or performing maintenance. Following this rule will reduce the risk of
• erious personal injury.
•  Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule will reduce the risk of serious personal injury.
•  Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule will reduce the risk of serious personal injury.
•  Battery tools do not have to be plugged into an electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not using your battery tool or when changing accessories. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.
•  Do not place battery tools or their batteries near fire or heat. This will reduce the risk of explosion and possiblyinjury.
•  Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately.
•  Batteries can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any cordless product in the presence of open flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately.
•  Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with your skin, wash immediately with soap and water. If liquid gets into your eyes, flush them with clean water for at least 10 minutes, then seek immediate medical attention. Following this rule will reduce the risk of serious personal injury.
•  Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also.

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

SYMBOL| SIGNAL| MEANING
| DANGER:| Indicates a hazardous situation, which, if not avoided, will result in death or serious injury.
| WARNING:| Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
| CAUTION:| Indicates a hazardous situation, that, if not avoided, may result in minor or moderate injury.
 | NOTICE :| (Without Safety Alert Symbol) Indicates information considered important, but not related to a potential injury (e.g. messages relating to property damage).
Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

SYMBOL| NAME| DESIGNATION/EXPLANATION|
| Safety Alert| Indicates a potential personal injury hazard.
| Read Operator’s Manual| To reduce the risk of injury, user must read and understand operator’s manual before using this product.
|

Eye Protection

| Always wear eye protection with side shields marked to comply with ANSI Z87.1.

| Wet Conditions Alert|

Do not expose to rain or use in damp locations.

 |

Hot Surface

| To reduce the risk of injury or damage, avoid contact with any hot surface.
 |

Recycle Symbol

| This product uses lithium-ion (Li-ion) batteries. Local, state or federal laws may prohibit disposal of batteries in ordinary trash. Consult your local waste authority for information regarding available recycling and/ or disposal options.
V| Volts| Voltage
min| Minutes| Time
| Direct Current| Type or a characteristic of current
no| No Load Speed| Rotational speed, at no load
…/min| Per Minute| Revolutions, strokes, surface speed, orbits etc., per minute|

ASSEMBLY

Do not use this product if it is not completely assembled or if any parts appear to be missing or damaged. Use of a product that is not properly and completely assembled or with damaged or missing parts could result in serious personal injury. WARNING: Do not attempt to modify this product or create accessories or attachments not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

OPERATION

• APPLICATIONS
  You may use this product for the purposes listed below:  Removing and installing threaded fasteners

• OVERLOAD PROTECTION
  When the tool is forced or overloaded, the Li-ion battery pack will automatically shut off the tool. To reset the tool, release the trigger and resume operation. If the tool still does not resume operation, remove and reinsert the battery. Do not force the tool.

• HIGH-TEMPERATURE PROTECTION
  Li-ion battery packs are equipped with a high temperature protection feature that automatically deactivates the tool when the motor is overheated. To resume operation, allow the tool to cool and then squeeze the trigger.

• INSTALLING/REMOVING THE BELT CLIP
  The belt clip (not included) can be installed on either side of the tool.

•  Align hole in belt clip with hole in tool’s base.

•  Install screw to secure belt clip in place.

•  To uninstall, remove screw and then belt clip.

• INSTALLING/REMOVING BATTERY PACK

•  Lock the switch trigger.

•  Insert the battery pack into the product as shown.

•  Make sure the latches on each side of the battery pack snap into place and that battery pack is secured in the product before beginning operation.

•  Depress the latches to remove the battery pack. For complete charging instructions, see the operator’s manuals for your battery pack and charger.

•  Lock the switch trigger and remove the battery pack.

•  Grab the collar firmly and pull it away from the tool.

•  Rotate the ratchet head to your desired position.
  NOTE: The head can be set to 0˚, 90˚, 180˚, and 270˚.
  Once the ratchet head is in one of the four indexed positions, the spring- loaded collar will snap back into place.

• LOCKOUT LEVER
  The lock out lever reduces the possibility of accidental starting. The lock out lever is located on the handle above the switch trigger. The lock-lever must be in the unlocked position before you pull the switch trigger. When not in use, slide lock-lever down to lock the switch trigger.

• VARIABLE SPEED SWITCH TRIGGER
  The variable speed switch trigger delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure. To turn the tool ON, move the lock out lever to the unlocked position and depress the switch trigger. To turn it OFF, release the switch trigger and allow the tool to come to a complete stop. NOTE: A whistling or ringing noise coming from the switch during use is a normal part of the switch function. Battery tools are always in operating condition. Lock the switch when not in use or carrying at your side, when installing or removing the battery pack, and when installing or removing sockets.

• LED LIGHTS
  The LED lights near the collar illuminate when the switch trigger is depressed. If the tool is not in use, the time-out feature will cause the light to start fading and then shut off. The LED lights illuminate only when there is a charged battery pack in the tool.

• INSTALLING AND REMOVING SOCKETS
  See Figure 6, page 9. Always select the correct size socket for nuts and bolts. Using the wrong size socket may damage the nut or bolt and cause the fastening torque to be inaccurate or inconsistent.

•  Lock the switch trigger and remove the battery pack.

•  Push a 3/8 in. socket (not included) onto the anvil until the detent pin locks it into place.

•  To remove the socket (not included), pull it away from the anvil.

• OPERATING THE RATCHET
  WARNING: Do not drive a bolt where there is likely to be hidden wiring behind the surface. Contact with a “live” wire willmake exposed metal parts of the tool “live” and shock the operator. If you must drive a bolt where hidden wire could be present, always hold tool by insulated gripping surfaces (handle) when performing the operation to prevent a shock to the operator.
  NOTICE: The ratchet is not designed to be used as a drill. Proper fastening torque is determined by the kind of bolt, the size of the bolt, or the material of the workpiece. This tool is designed only to speed the installation and removal process and is not intended to replace a torque wrench. For applications where proper torque is important, always use a torque wrench to verify that proper torque is achieved. NOTE: Do not use this tool to install lug nuts on wheels.

•  Install the desired socket.

•  Adjust the forward/reverse dial on the back of the ratchet head to choose the desired rotation direction of the socket.

•  Hold the tool in front of the workpiece with the socket over the nut or bolt.

•  Depress the switch trigger and fasten or loosen as desired. NOTE: After fastening, always check the torque with a torque wrench.

References

• REIMAGINE WITH RYOBI - RYOBI Tools

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>