Syinix 32E4M Digital TV User Manual
- June 5, 2024
- Syinix
Table of Contents
LED(BACKLIGHTING) COLOR TELEVISION
32E4M
User Manual
Please read this instruction manual carefully before usage and save it for future reference.
Installation
-
Install the TV in the room where direct sunlight does not fall on the TV. Total darkness or a reflection on the picture screen can cause eyestrain. Soft and indirect lighting is
recommended for comfortable viewing. -
Allow enough space between the TV unit and the wall to permit ventilation.
-
Avoid excessively warm locations to prevent possible damage to the cabinet or premature component failure.
-
Do not install the TV in a location near heat sources such as radiators, air ducts, or direct sunlight, or in a place somewhere like close compartments and closed areas. Do not cover the ventilation openings when using the TV.
-
The indicator light will last about 30 seconds to go out after cutting off the electricity, during this period, you cannot repower it on until the indicator light goes out.
-
To prevent the spread of fire, keep candles or other open flames away from this product at all times. Thanks a lot for your attention!
Warning
CAUTION
THE RISK OF ELECTRIC SHOCK DOES NOT OPEN
CAUTION: TO AVOID THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE THE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to avoid the risk of electric shock,
do not disassemble this equipment by anyone except qualified service
personnel.
This symbol is intended to alert the user to the presence of important
operating and maintenance instructions in the literature accompanying the
equipment.
This equipment is a Class II or double insulated electrical appliance. It has
been designed in such a way that it does not require a safety connection to
electrical earth.
Caution
Caution
High voltages are used in the operation of this product. Do not open the
product’s casing. Refer servicing to qualified service personnel.
Caution
Never stand or push or lean on the product or its stand. You should pay
special attention to children.
Caution
To prevent fire or electrical shock hazards, do not expose the unit to rain or
moisture. Do not place objects filled with liquids, such as vases, on the
apparatus.
Caution
Do not place the main unit on an unstable cart stand, shelf or table. Serious
injury to an individual, and damage to the television, may result if it falls.
Caution
Do not drop or push objects into the television cabinet slots or openings.
Never spill any kind of liquid on the television receiver.
Caution
When the product is not to be used for a longer period of time, it is
advisable to disconnect the AC power cord from the AC outlet.
Caution
Avoid exposing the main unit to direct sunlight and other sources of heat. Do
not put the television receiver directly on other products which give off the
heat: e. g. video cassette players amplifiers. Do not block the ventilation
holes at the back cover. Ventilation is essential to prevent the failure of
the electrical components. Do not squash the power supply cord under the main
unit or under the other heavy objects.
Caution
The LED panel used in this product is made of glass, therefore it can break
when the product is dropped or applied with impact. Be careful not to be
injured by broken glass
pieces in case the LED panel breaks.
Menu Operation
Installation Guide
If this is the first time you are turning on the TV and there are no programs
in the TV memory, the “Installation Guide” menu will appear on the screen.
-
Select OSD language
Press the “▲/▼”and “Enter” buttons to select the local language.
Press the “GREEN” button to go to the next page.
-
Select local country
Press the “▲/▼”and “Enter” buttons to select the local country.
Press the “GREEN” button to go to the next page and the “RED” button to go to the previous page.
-
Select Scan or Homepage
Press “▲/▼” to select Auto Scan or Home Page.
Press ►/the OK button to confirm.
-
Select auto search channel
Press the “▲/▼”and “Enter” buttons to select the auto search channel way.
Press the “RED” button to go to the previous page.
Note:
- The picture is provided for reference only since the information displayed may be different.
- Searching for a platform will take a long time, please be patient!
PICTURE
You can select the type of picture mode that best suits your personal
preference. Press the “MENU” button to enter the OSD menu, then press “ ‘ to
select “Picture” in the main menu and to select the item you want to change.
Use “ ” button to select the desired setting.
SOUND
You can select the type of sound mode that best suits your personal
preference. Press the “MENU” button to enter the OSD menu, then press “ to
select “Sound” in the main menu and to select the item you want to change. Use
the “ ” buttons to select the desired setting.
CHANNEL
Press the “MEW’ button to enter the OSD menu. Then press the “ ” and “ ”
buttons to select the -Channel” menu and to set the desired setting.
-
Press the” button to select “Channel Management”. Press the “ENTER” button to enter the sub-menu.
a. Lock
Press the “ button to select the program and press the “GREEN” button on the remote control to lock the program. The default password is “0000”. Note: These settings can be adjusted only when the “Lock Channel’ Is set to ‘On”.
b. Delete
Press the” ” button to select the program and press the “READ” button on the remote to delete the program.
c. Skip
Press the “ button to select the program and press the “YELLOW” button on the remote to skip the program. Press the “YELLOW” button again to cancel the setting.
d. Move
Press the “ button to select the channel and press the “BLUE’ button to select, moving the channel to the position where you want to move by pressing the “ button. Then press the “BLUE’ button again to confirm. -
Press the “ button to select “Favorite Management” and press the “ENTER” button to enter the sub-menu. Then you can add channels to the different favorite lists by pressing the “RED”, “GREEN”, “YELLOW”, and “BLUE’ buttons. You can call the favorite list by pressing the “FAV” button after setting.
-
Press the “ button to select “Country/region” and press the “ENTER”. Then select your country.
-
Press the “ button to select the “Auto search” menu and press the “ENTER” button to enter the sub-menu. Then you can select the “Auto search” channel way. NOTE: Searching for a platform will take a long time. Please be patient!
-
Press the “ button to select “DTV Manual Search” and press the “ENTER” button to enter the sub-menu. Then you can set the related parameters and press “Start’ to start searching.
NOTE: It is used only in DTV mode -
Press the “ button to select “ATV Manual Search” and press the “ENTER” button to enter the sub-menu. Then you can set the related parameters.
NOTE: It Is used only in ATV mode
FEATURE
Press the “MENU” button to enter the OSD menu. Press “ to select “Feature” in the main menu and to select the item you want to change. Use the “ ” button to select the desired setting.
Press the “ button to select “Lock” in the “Feature” menu and press the “ENTER” button to input the password, then you can see the sub-menu and set related parameters.
Note: The default password is “0000”.
SETUP
Press the “MENU” button to enter the OSD menu. Then press the “ and “ buttons to select the “Setup” menu.
**PVR Operation
**
- Press the “SOURCE’ and “ buttons to the DTV source. Then press the “MENU” and “ buttons to select the “Feature” menu.
- Press the “ and “ buttons to select the “PVR/Timeshift” and press the “ENTER” button to enter.
-
Press the” ” button to select the “Partition Select’ menu and press the “ENTER” button to enter the sub-menu as follow.
-
Press the” ” button to select the ‘Timer’ menu and press the “ENTER” button to enter the sub-menu. Then you can press different colored buttons to do different operations according to instructions at the bottom of the OSD.
-
Press the “ button to select “Record List” in the menu and press the “ENTER” button to enter the sub-menu as follow. You can press the “ button to select the different options and use the “ ****buttons to play or pause the recorded file.
-
Press the” ” button to select “Recorder Start” in the menu and press the “ENTER” button to start recording.
Note: The U disk may be formatted when in recording, please do not store important files.
i-Cast
TV Mirror
-
Press the “SOURCE” button on the TV remote control, then the TV goes into the i-Cast screen and waits for a connection with a cell phone. The cell phone screen will appear a message to configure the device to connect to the TV.
-
Select the “Mirroring” function of your cell phone screen, then the cell phone screen will project to the TV.
Note: Depending on the cell phone the message that appears on the phone screen will differ.
DVB-S2 Channel Search Manual
Auto search
-
.Enter the Channel page of the TV menu and select Satellite for TV Connection.
-
Then enter the Auto Search sub-menu and select DTV as the single search DTV station. The interface is as follows.
Manual search
-
Select satellite and set satellite parameters.
Open the Menu, and select Channel Page, enter the Satellite System page.
-
Press the green button in the four-color button to edit. Operations in the satellite edit menu are shown in the following.
Satellite Enter Satellite Rename edit menu
Longitude Direction East, West
Longitude Angle Press the num key to set the Angle
Band C, Ku -
Press the blue button in the four-color button to start the manual search of DVB-S/S2.
Scan Mode| Default, Network Search, Full Search
---|---
Channel Type| All, TV only
Service Type| All Services, Free Service
Polarity| Auto, Vertical, Horizontal
Trouble Shooting
Before consulting service personnel, check the following chart for possible solutions.
PROBLEM | SOLUTION |
---|---|
TV will not turn on | •Make sure the power cord is plugged in. |
•The batteries in the remote control may be exhausted, replace the batteries.
No picture, no sound| •Check the cable between TV and antenna/external AV
device.
•Press the power button on the remote. Press the SOURCE button on the remote,
then press the “ button repeatedly to select the TV source.
Poor picture, sound OK| •Check the cable between TV and antenna/external AV
device.
•Try another channel, the station may have broadcast difficulties.
•Adjust the brightness/contrast in the
“Video” menu. Check that the unit is set to PAL/SCEAM
Audio noise| •Move any infrared equipment away from the TV.
The TFT LED panel uses a panel consisting of sub pixels which require sophisticated technology to produce. However, there may be a small number of bright or dark pixels on the screen. These pixels will have no impact on the performance of the product.
If at any time in the future, you should need to dispose of this product please note that: Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your Local Authority or retailer for recycling advice. (Waste Electrical and Electronic Equipment Directive)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>