Parkit360 5K Force Electric Trailer Dolly with Intelligent Speed Control User Manual

: June 5, 2024
: Parkit360

Parkit360 5K Force Electric Trailer Dolly with Intelligent Speed Control User Manual

IN THE BOX

PACKAGES INCLUDE:

Force Dolly & Handle
Ball Mount: 18”, 20” or 24”
Tightening Bar
Two Hitch Balls: 2” & 2 5/16”
Thrust Washer (Puzzle)

Hardware Kit:

2 Handle Spring Clips
Allen Key & Screws
Battery Cable

Battery Hardware & Charger Cable (B2 + B3 Packages Only)

ASSEMBLY

Insert the Handle into the Dolly and tighten both Allen Screws to secure it.

Plug the Handle Cable into the Port on the Dolly’s Module. Install both Spring Clips onto the Handle for easy access to the Tightening Bar.

U1 Battery Kit: Pre-installed when purchased with a B2 or B3 Dolly.
Battery Box Kit: Mount the Plastic Battery Box with the provided Strap.

FEATURES

SMART BRAKE (B2+B3)
7-Way Power Plug that Controls the Trailer’s Electric or Surge Brakes.

BATTERY CABLE PLUG
Power the Dolly with an On-board Battery or Connect to a Trailer Battery.

INTELLIGENT SPEED CONTROL™
Toggle between High and Low Speed.
Motor Starts and Stops gradually for a smoother parking experience.

FREEWHEEL KNOB
Engages/Disengages Motor to switch between Drive and Neutral. (Page 4)

OPTIONAL PARTS

Telescopic Frame Adapter
EZ Connect Adapter
1 7/8” or 50mm Hitch Ball
Pintle Hitch Adapter
Atwood Hitch Adapter
Smart Brake
U1 Battery Kit
Battery Box Kit
OPTIONAL PARTS

ORDER ONLINE or CALL TOLL-FREE:

1-888-926-5517 ext. 1
PARKIT360.COM

MODULE FEATURES

HANDLE PLUG

Plug in and twist locking cap over connection.
Unplug cable while charging the battery
MODULE FEATURES
DANGER: DO NOT EXCEED MAXIMUM WEIGHT CAPACITY OF THIS UNIT! CAN CAUSE DAMAGE TO YOUR TRAILER OR SERIOUS INJURY. REFER TO USER MANUAL BEFORE OPERATION. DO NOT OPERATE ON MORE THAN 6% GRADE. ENSURE UNIT IS STABLE BEFORE OPERATING.

CIRCUIT BREAKERS

By default, the Brake Button protrudes more than the Motor.

BATTERY CHARGER PLUG

With the battery connected, plug into wall outlet to charge.

ISC CONTROL™

While parking your trailer, switch between High or Low Speed anytime by flipping the toggle switch.
Motor speed starts and stops gradually for better traction and a smoother parking experience.

VOLT METER

Digital Meter that measures and displays Power Level of Battery.
Fully Charged Batteries Rest between 12.6 to 13V.

CIRCUIT BREAKERS

Prevents Motor and Smart Brake from overheating.
If a breaker trips, the Reset Button will extend up to 1/2” from the panel.
Allow 30 seconds for the system to cool down, then press Reset.

BATTERY CHARGER

Ensure the Battery and Charger Cable are plugged into the Dolly. Plug the Charger Cable into a Wall Socket to charge. Disconnect the charger after an over-night charge (10 hrs Max).
To prevent accidental operation while charging, unplug the Handle Cable.

FREEWHEEL KNOB: SWITCHING GEARS

FREEWHEEL/SPOOL

NEUTRAL. MOVE THE DOLLY WITHOUT POWER WHILE IT IS NOT UNDER LOAD.

Turn the knob in the direction of the Freespool arrow until it stops. Freely move the dolly to and from the trailer in this mode.
This mode is intended for transportation only

DRIVE

ENGAGE THE MOTOR TO CONNECT TO THE TRAILER AND PARK WITH POWER.
DRIVE

Ensure the Dolly is in parking position underneath the trailer hitch.
Turn the knob in the direction of the Engaged arrow until it stops and clicks into position. Rock the Dolly back and forth to ensure the motor is engaged.
When pushed manually in this mode, the Dolly will only move an inch forwards or backwards before stopping.

POWER OPTIONS

DOLLY-MOUNTED BATTERY

U1 BATTERY KIT
Connect the 6” Cable to both battery terminals with the provided hardware. Plug the cable into the Dolly to turn it ON.

12v U1 SEALED BATTERY CONNECT 6” BATTERY CABLE

12v GROUP 24 DEEP CYCLE BATTERY CONNECT 20” or 80” BATTERY CABLE

BATTERY BOX KIT

Install the Battery Box with the strap provided. Use the 20” Cable to connect to a 12 Volt Group 24 Deep Cycle or Marine Battery.

TRAILER BATTERY

TWO 12v BATTERIES
Connect the 80” Cable to either Trailer Battery:

TWO 6v BATTERIES
Connect the 80” Cable across Both Batteries:
TRAILER BATTERY

PLUG IN TO POWER ON UNPLUG TO POWER OFF.

DANGER

DO NOT EXCEED DOLLY’S MAX. WEIGHT CAPACITY
CAN CAUSE DAMAGE TO YOUR TRAILER, SERIOUS INJURY, OR EVEN DEATH.

FORCE 5K
UP TO 5,000 LBS

FORCE 10K
UP TO 10,000 LBS

RE-TIGHTEN BALL MOUNT BEFORE OPERATION

USE JACK POST CONNECTION OR TELESCOPIC FRAME ADAPTER FOR TRAILERS:

BETWEEN 8,000-10,000 LBS GROSS WEIGHT
WITH MORE THAN 800 LBS TONGUE WEIGHT
WITH ARTICULATED HITCHES

DO NOT OPERATE ON MORE THAN 6% GRADE

RISK OF RUNAWAY TRAILER.
DO NOT OPERATE ON STEEP INCLINES.

CONNECTING TO YOUR TRAILER:

BALL MOUNT ADAPTER

While in Freewheel Mode, move the Dolly and Accessories to the Trailer.
Choose your preferred Hitch Ball Size, and assemble the Ball Mount.
BALL MOUNT ADAPTER

BALL MOUNT ASSEMBLY

HITCH BALL

Thread desired Hitch Ball into the Ball Mount. Apply a generous portion of All-Purpose Grease along the top surface of the Ball Mount Collar.

The shoulder of the Hitch Ball should rest slightly below the top of the collar

HITCH BALL PLACEMENT

WELD SPOTS

Insert the assembled Ball Mount into the Hitch and lock as normal.

Make sure the Weld Spots on the Hitch Ball are pointed towards the rear left side of your trailer at about 10 o’clock.

HITCH CONNECTION

Turn the Ball Mount Counterclockwise until the gap between the Ball Mount Collar and Trailer Tongue closes tightly, with no gap.
HITCH CONNECTION

**** Have a Gap or Step Down Hitch preventing a flush connection?

TIGHTEN THE BALL MOUNT

TIGHTENING BAR
Once the Ball Mount is secure, use the Tightening Bar to ensure the connection is as tight as possible!
This will take a few rotations.

CONNECTION GAP?

THRUST WASHER with PUZZLE PIECE

Space between the Ball Mount and Coupler?

Install the Thrust Washer on top of the Ball Mount with the Puzzle Piece facing the Parkit360 Dolly

Tighten Ball Mount as normal.
CONNECTION GAP

STEP DOWN HITCH?

THRUST WASHER

Have an obstruction preventing a flat connection?

Place the Thrust Washer on top of the Ball Mount with the open section facing the trailer.

While tightening, hold the Thrust Washer in place to prevent it from spinning

STILL HAVING TROUBLE?

DANGER

OPERATING WITH A LOOSE OR UNEVEN CONNECTION CAN CAUSE DAMAGE TO YOUR TRAILER OR PERSONAL INJURY.
STILL HAVING TROUBLE

ENGAGE MOTOR INTO DRIVE

CONNECT BATTERY
Plug the Battery Cable into the Dolly to turn it ON. 12v U1 Sealed Battery shown.

ENGAGE MOTOR
Ensure the Dolly is in Drive by turning the Freewheel Knob towards the Engaged Arrow. See page 4 for details.
ENGAGE MOTOR INTO DRIVE

ALIGN THE DOLLY

Using the Handle Toggle Switch, Drive the Dolly underneath the hitch. Align the Ball Mount with the top of the Dolly’s Receiver Tube.

ALIGN THE DOLLY

INSERT BALL MOUNT

Reverse the Dolly to Level, then lower Ball Mount fully into the Receiver Tube. Wiggle the handle up and down to release Ball Mount friction.

Ensure that the Jack Post is off of the ground.
INSERT BALL MOUNT

RE-TIGHTEN BALL MOUNT

Using the Toggle Switch, move the Dolly back & forth slightly. Re-tighten Ball Mount. Repeat 2-3 times or until you can’t tighten anymore.

READY!

ENSURE CONNECTION IS AS TIGHT AS POSSIBLE BEFORE OPERATING!

PARKING YOUR TRAILER

Use the Forward and Reverse Toggle Switch to steer into tight spaces that are nearly impossible for vehicles.

Switch between High or Low Speed anytime using the Intelligent Speed Control Switch.

DISCONNECTING THE HITCH

Chock Trailer Wheels to prevent a runaway trailer.
Unplug the Battery Cable from the Dolly. Raise the Trailer to withdraw the Ball Mount, then switch to Freewheel Mode.

The Ball Mount can be removed or left on the hitch for later use.

STORAGE & MAINTENANCE

Freewheel the Dolly to desired storage area, preferably under cover. Charging the On-Board Battery: Plug the Battery Cable into the Dolly.

Unplug the Handle Cable, then plug the Dolly’s Charger Cable into a wall outlet. Always unplug the battery charger after 10 hours even if the green light does not come on.

Grease the Receiver Tube and Lubricate the Chain with Chain Lube. Can be done annually, or more often if used more frequently.

CALL TOLL-FREE:
1-888-926-5517
Ext. 1 – Sales & Service
Ext. 2 – Administration

OFFICE HOURS (WEEKDAYS)
8AM-4PM EST
sales@parkit360.com
admin@parkit360.com
support@parkit360.com

ALTERNATIVE CONNECTIONS

TRAILER JACK POST

Remove the Ball Mount Adapter. Lower the Trailer Jack into the Dolly’s Receiver Tube, following the standard connection process.

The trailer should rest as close to the Dolly’s Tires as possible to reduce strain on the Jack Shaft.
TRAILER JACK POST

TELESCOPIC FRAME ADAPTER

Remove the Ball Mount Adapter. Attach the Telescopic Adapter to the Y section of the trailer frame.

Lower the Telescoping Pipe into the Dolly, following the standard connection process. Slide the Adapter’s locking pin into place.
TELESCOPIC FRAME ADAPTER

THRUST WASHER: ATWOOD HITCH ADAPTER

With the Thrust Washer base on the Ball Mount, interlock the Atwood Adapter piece.

Thread the Hitch Ball and Tighten as Normal. Hold the adapter in place to prevent it from spinning.

2 YEAR PARTS & REPAIR WARRANTY

Your Parkit360 Force Dolly is covered for 2 years from the initial date of purchase. If a defect is found during this time, contact us with the original sales receipt number and details of the fault encountered.

Our Technical Support will attempt to solve the issue remotely. If the issue appears to be caused by defective parts, we will provide free replacement parts, excluding shipping costs.

If the 2 Year Warranty has expired or if you are not the original owner, you will have to pay the cost of parts and shipping. This repair will be covered for 3 months, starting 7 days from the date of shipment.

The Repair Warranty will expire either at the end of the 3 month period, or at the expiration of the original 2 -Year Warranty, whichever is later.

30 DAY RETURN POLICY

If a material defect is found or if the Parkit360 Force Dolly has failed to perform to your expectations, return it within 30 days of the date of sale for a refund, less the flat shipping cost of $250 and 20% restocking fee.

Pack the Dolly and U1 Battery Kit back into the box that it came in.
Call us at 1-888-926-5517 x 1 to let us know when your package is ready. Please provide us with your Sales Receipt or Online Order number.
Our staff will provide you with an RMA# that must be written on the box prior to sending. We will email you a Return Shipping Label that must be affixed to the box prior to drop off at your nearest FedEx Depot. (If you are unable to drop off the Unit, Pick-Up can be arranged.)
Receive your refund minus the shipping and restocking fee once the Dolly arrives at our warehouse.

EXCLUSIONS AND LIMITATIONS

The 2 Year Warranty and 30 Day Return Policy do not cover: