behringer SF300 Super Fuzz 3-Mode Fuzz Distortion Effects Pedal Instructions
- June 5, 2024
- Behringer
Table of Contents
behringer SF300 Super Fuzz 3-Mode Fuzz Distortion Effects Pedal
Thank you for showing your confidence in us by purchasing the Behringer SUPER
FUZZ SF300. This effects pedal is ideally suited for electric guitars and
recreates the whole variety of famous fuzz tones of the 60s and70s.
Controls
-
The LEVEL control adjusts the output level.
-
The TREBLE control allows you to boost/cut the high-frequency range.
-
The BASS control allows you to boost/cut the low-frequency range.
-
The GAIN control adjusts the gain for more distorted sounds.
-
The MODE switch lets you choose between 3 effect modes.
FUZZ 1: Basic fuzz sound with emphasis on the midrange.
FUZZ 2: Full-bodied fuzz sound with scooped mids and sharp harmonics.
BOOST: The Level control is inactive and the Gain control adjusts the boost. -
The ON/BATT LED illuminates when the effect is activated. It also serves as a battery level indicator.
-
Use the footswitch to activate/deactivate the effect.
-
Use this ¼” TS IN connector to plug in the instrument cable.
-
The ¼” TS OUT connector sends the signal to your amp.
Use the DC IN connection to plug in a 9 V power supply (not included).
The BATTERY COMPARTMENT is located underneath the pedal cover. To install or replace the 9 V battery (not included), press the hinges with a ballpoint pen and remove the pedal cover. Be careful not to scratch the unit.
The SF300 has no on/off switch. As soon as you insert the plug into the in connector, the SF300 is on. When not in use, remove the plug from the in connector. This extends the life of the battery.
The SERIAL NUMBER is located at the underside.
Safety Instructions
Do not use near water, or install near heat sources. Use only authorized attachments/accessories. Do not service product yourself. Contact our qualified servicing personnel for servicing or repairs, especially when power supply cord or plug is damaged.
Limited Warranty
For the applicable warranty terms and conditions and additional information regarding Music Tribe’s Limited Warranty, please see complete details online at musictribe.com/warranty.
Specifications
In
Connector| ¼” TS
Impedance| 500 kΩ
Out
Connector| ¼” TS
Impedance| 1 kΩ
Power Supply
9 V, 100 mA regulated
Behringer PSU-SB
USA/Canada| 120 V~, 60 Hz
Europe/U.K./ Australia| 230 V~, 50 Hz
China| 220 V~, 50 Hz
Korea| 220 V~, 60 Hz
Japan| 100 V~, 50/60
Power connector| 2 mm DC jack, negative center
Battery| 9 V type 6LR61
Power consumption| 30 mA
Physical/Weight
Dimensions (H x W x D)| approx. 2 1/8 x 2 3/4 x 4 4/ approx. 54 x 70 x 123 mm
Weight| approx. 0.73 lbs / 0.33 kg
Music Tribe accepts no liability for any loss which may be suffered by any person who relies either wholly or in part upon any description, photograph, or statement contained herein. Technical specifications, appearances and other information are subject to change without notice. All trademarks are the property of their respective owners. Midas, Klark Teknik, Lab Gruppen, Lake, Tannoy, Turbosound, TC Electronic, TC Helicon, Behringer, Bugera, Oberheim, Auratone and Coolaudio are trademarks or registered trademarks of Music Tribe Global Brands Ltd. © Music Tribe Global Brands Ltd. 2021 All rights reserved.
FEDERAL COMMUNICATIONS COMMISSION COMPLIANCE INFORMATION
SUPER FUZZ SF300
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
- This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference
that may cause undesired operation.
Important information:
Changes or modifications to the equipment not expressly approved by MUSIC
Tribe can void the user’s authority to use the equipment.
Hereby, Music Tribe declares that this product is in compliance with Directive 2014/30/EU, Directive 2011/65/EU and Amendment 2015/863/EU, Directive 2012/19/EU, Regulation 519/2012 REACH SVHC and Directive 1907/2006/EC.
Full text of EU DoC is available at https://community.musictribe.com/
EU Representative: Music Tribe Brands DK A/S
Address: Ib Spang Olsens Gade 17, DK – 8200 Aarhus N, Denmark
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>