REKKORD F 110P Fully Automatic Turntable User Manual
- June 3, 2024
- REKKORD
Table of Contents
REKKORD F 110P Fully Automatic Turntable
INSTALLATION
- Dustcover
- Hinge
- Cue control
- Speed selector
- Start-Stop-Switch
- Transportation lock
- Tonearm rest
- Phono cable
- Ground
- Socket for power supply
- Stylus
Preliminary operations
Unpack the unit and all accessories. Please keep the packaging for future use when transporting the device. Remove the two transport lockings 6 by pressing them sidewards (fig. 1). Fit the platter and depress the locking mechanism in its center until it engages in the groove of the platter spindle (fig. 2). Insert the hinges 2 in the appropriate recesses (fig. 3). Slide the cover 1 parallel to the position of the hinges 2 (opening angle approximately 60°) until it locks in place. In this position, the body can be removed at any time.
Power supply
The delivered power supply will be connected to socket 10 at the back of the device. The mains set, corresponding to the voltage indicated on the nameplate has to be plugged in to a power-supply plug either with 230V/50 Hz or 115 V/60 Hz on the primary side.
Connection to amplifier or preamp (F110)
Connect the phono cables 8 to the phono-magnetic-inputs of the amplifier or
preamp (red or black RCA-type plug = right channel, white RCA-type plug = left
channel). Connect Ground 9 to the ground connector of your amplifier or
preamp.
Connection to the amplifier (F110 P)
Connect the phono cables 8 to a Line Input (CD/AUX) of your amplifier (red or
black RCA-type plug = right channel, white RCA-type plug = left channel).
Ground 9 has no function in this case
Automatic start, speed selection 33/45
The speed must be selected according to the record which is in place. If the
turntable speed is set to 33 or 45 rpm 4 the record size is automatically
selected for the automatic start. Remove stylus cover forwards for the pick-up
stylus and move switch 5 to Start. The pick-up arm automatically lowers onto
the record.
Manual start, stop
The speed must be selected according to the record which is in place. Use
switch 6 to select a speed of 33 or 45 rpm. Remove stylus cover forwards and
move lift lever 3 into position . Now position the tonearm over the lead-in
groove of the record. The tonearm can now lowered slowly onto the record using
the cueing lever 3 , thus preventing damage to your records. The tonearm can
be raised at any position, also for brief interruptions when playing, by using
the cue control lever (cueing in position ). The platter continues to rotate
in this case. At the end of record, the tonearm is automatically repositioned
back on the tonearm post and the unit is switched off. — You can also switch
off the turntable by setting switch 5 to Stop or setting the cueing lever 3 to
position and repositioning the tonearm on the tonearm rest 7.
Safety precautions
To prevent the risk of fire or electrical damage, do not expose the device to moisture or rain. Please do not open the device! Keep the packaging material, such as plastic foils, away from children. Danger of asphyxiation by misuse.
Disposal of electrical appliances by consumers in private households within
the EU
At the end of its lifetime, do not throw the device away with the normal
household waste. Ask about the options for environmentally sound disposal at
the local authorities, at recycling centers, or where you purchased the
device. This product complies with applicable EU regulations
Technical data
Belt Drive
- Main voltage 230 V / 50 Hz 115 V / 60 Hz
- Line frequency 50 / 60 Hz
- Power requirement 1,5 W
- Platter speeds (rpm) 33, 45
- Wow and flutter +/- 0,1 / 0,04 %
- Signal-to-noise ratio (DIN 45500) Rumpel unweighted signal-to-noise Rumpel weighted signal-to-noise 42 dB 65 dB
- Effective tonearm length 211 mm
- Offset angle 26°
- Overhang 19,5 mm
- Tangential tracking error 0,15° / cm Rad
- Cartridge OM 10
- Tracking force 15 mN (1,5g)
- Frequency range 20 Hz – 20 kHz
- Output 4 mV / 1000 Hz, 5 cm/sec.
- Tracking capability 70 um
- Cartridge weight 5 g
- Dimensions (WxHxD) 430 x 365 x 130 mm
More info
www.rekkord-audio.com
Ask us
Technicalquestions: support@rekkord-audio.com
General questions: info@rekkord-audio.com
REKKORDAudio
a Divisionof AudioTuningVertriebs GmbH
Billing address:
Margaretenstrasse 98
A-1050Wien
AUSTRIA
Headquarter&Logistics:
Wirtschaftspark A5 Mistelbach/Wilfersdorf
Analogweg 1,2130Mistelbach
AUSTRIA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>