REKKORD M 500 Sub Chassis Turntable User Manual

REKKORD M 500 Sub Chassis Turntable

Safety precautions

CAUTION!

• To prevent the risk of fire or electrical damage, do not expose the device to moisture or rain.
• Do not expose the device to direct sunlight or heat!
• Please do not open the device!
• Keep the packaging material, such as plastic foils, away from children.
• Danger of asphyxiation by misuse.

Disposal of electrical appliances by consumers in private households within the EU
At the end of its lifetime, do not throw the device away with the normal household waste.
Ask about the options for environmentally sound disposal at the local authorities, at recycling centers, or where you purchased the device.
This product complies with applicable EU regulations.

1. Tonearm counterweight
2. Scale for setting tonearm tracking force
3. Antiskating setting
4. Head-shell locking nut
5. Securing screw for cartridge
6. Touch panel
7. Stylus
8. Hinge
9. Dustcover
10. Tonearm support with tone arm lock
11. Cue control
12. Left audio output
13. Right audio output
14. Ground
15. Connection socket for power supply
16. Transport locking’s

Preliminary operations

Unpack the unit and all accessories. Please keep the packaging for future use when transporting the device.
Remove the two transport lockings 16 by using the allen wrench.
Fit the platter and depress the locking mechanism in its centre until it engages in the groove of the platter spindle.
Insert the hinges 8 in the appropriate recesses.
Slide the cover 9 parallel to the position of the hinges 8 (opening angle approximately 60°) until it locks in position. In this position, the cover can be removed at any time.

Power supply

The delivered power supply will be connected to the socket 15. The mains set, corresponding to the voltage indication on the nameplate has to be plugged in to a power-supply plug either with 230V/50 Hz or 115 V/60 Hz on the primary side.

Connection to amplifier or preamp

Connect RCA plugs of the audio cable to the phono-magnetic-inputs of the amplifier or preamp (red or black RCA-type plug = right channel, white RCA-type plug = left channel) an connect the other side to the corresponding connectors
12+13 at the turntable.
Connect Ground on the turntable 14 to the ground connector of your amplifier or preamp.

Balancing the tonearm, setting tracking force and antiskating

1. Set tracking force 2 to 0 and switch off antiskating 3.
2. Remove the stylus protection.
3. Turn the tonearm counterbalance 1 on the tonearm. Unlock the tonearm and move it over to the tonearm rest. Pull the cue control 11 in your direction to the front in order to bring the cue control down.
4. Balance the tonearm precisely by turning the counterbalance. The tonearm is balanced precisely when it pivots freely.
5. Set the required tracking force for the cartridge used by turning the dial 2. The tracking force for series cartridges 2M Red = 17,5 Nm = dial position 1.75.

Set the appropriate value of the antiskating device 3 on the basis of the following table:

Touch start, speed selection 33/45, stop

• With the touch switch 6 you can switch the device on and off and select the speed of the motor:
• Touch the touch field 1x briefly to start the motor at speed 33.
• Each further touch changes between 33 and 45.
• Place your finger on the switch 6 for at least 1.5 seconds to turn the device off.
• Please note, that the touch switch needs five seconds to calibrate itself after reconnecting the power supply.
• You can recognize the currently set speed by the color of the LED.
• White = 33.3 rpm
• Blue = 45 rpm

Mounting or exchanging a cartridge system

Change of cartridge system
Remove the cultured signal leads carefully from the cartridge pins with a pair of tweezers.

Unscrew the cartridge.
Screw the new cartridge onto the head shell but do not tighten.
Attach the leads to the pins while observing the correct coding.
Instead of the factory-supplied pick-up cartridge any other cartridge with standard half-inch mounting holes and a weight between 3 and 10 grams can be installed.

Change Headshell
Remove the coloured signal leads carefully from the cartridge pins with a pair of tweezers.
Loosen the collar-lock 4 behind the head shell.
Carefully pull the cultured signal leads out of the head shell. Install the head shell in reverse order.

Pay attention to the correct color coding:

• R = Red, right channel
• RG = Green, right channel ground
• L = White, left channel
• LG = Blue, left channel ground

Adjusting after change of pick-up cartridge system
For the precise adjustment of the so-called stylus overhang push the supplied mounting gauge into the head shell with cartridge. The adjustment is correct if the stylus is flush with the V-shaped recess in the gauge as viewed from above. When viewed from the side the stylus should be seen within the rectangular recess of the gauge. Adjust the cartridge in the head shell until the correct positions are achieved. Lastly, tighten the mounting screws, put the head shell with cartridge back on the tone arm and tighten the collar-lock 4.

ATTENTION!
During these mounting and adjustment procedures you must be very careful not to damage the delicate stylus, cables and cantilever by any brisk movements.

Technical data

• Belt Drive

• Main voltage

• Line frequency

• Power equirement

• Platter speeds (rpm)

• Wow and flutter

• Signal-to-noise ratio
  (DIN 45500)
  Rumpel unweighted signal-to-noise
  Rumpel weighted signal-to-noise

• Effective tonearm length

• Offset angle

• Overhang

• Tangential tracking error

• Cartridge

• Tracking force

• Frequency range

• Output

• Tracking capability

• Cartridge weight

• Dimensions (WxHxD)

Moreinfo
www.rekkord-audio.com

Askus
Technical questions: support@rekkord-audio.com
General questions: info@rekkord-audio.com
REKKORD Audio a Division of Audio Tuning Vertriebs GmbH

Billing address :
Margaretenstrasse 98
A-1050Wien

AUSTRIA
Headquarter&Logistics:
Wirtschaftspark A5 Mistelbach/Wilfersdorf
Analogweg 1,2130Mistelbach
AUSTRIA

References

• Rekkord

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>