REKKORD F100 Black Turntable Instruction Manual
- June 12, 2024
- REKKORD
Table of Contents
F100/F 100P – Black Turntable
Instruction Manual
F100 Black Turntable
- Dustcover
- Hinge
- Cue control
- Speed selector
- Tonarm support
- Start-Stop-Switch
- Stylus
- Phonocable
- Ground
Preliminary operations
Unpack the unit and all accessories. Please keep the packaging for future use
when transporting the device.
Insert the hinges 2 in the appropriate recesses (fig. 1).
Slide the cover 1 parallel to the position of the hinges 2 (opening
angle approximately 60°) until it locks in position. In this position, the
cover can be removed at any time.
Power supply
The delivered power supply will be connected to the socket 6 (fig. 2) at
the back of the device. The mains set, corresponding to the voltage indication
on the nameplate has to be plugged in to a power-supply plug either with
230V/50 Hz or 115 V/60 Hz on the primary side.
Connection to amplifier or preamp (F100)
Connect the phonocables 8 to the phono-magnetic-inputs of the amplifier or
preamp (red or black RCA-type plug = right channel, white RCA-type plug = left
channel).
Connect Ground 9 to the ground connector of your amplifier or preamp.
Connection to amplifier (F100 P)
Connect the phonocables 8 to a Line Input (CD/AUX) of your amplifier (red
or black RCA-type plug = right channel, white RCA-type plug = left channel).
The Ground 9 has no function in this case.
Automatic start, speed selection 33/45
The speed must be selected according to the record which is in place. If the
turntable speed is set to 33 or 45 rpm 4 the record size is automatically
selected for the automatic start.
Remove stylus cover forwards for the pick-up stylus and move switch 6 to
Start.
The pick-up arm automatically lowers onto the record.
Manual start, stop
The speed must be selected according to the record which is in place. Use
switch 6 to select a speed of 33 or 45 rpm.
Remove stylus cover forwards and move lift lever 3 into position .
Now position the tonearm over the lead-in groove of the record. The tonearm
can now lowered slowly onto the record using the cueing lever 3 , thus
preventing damage to your records.
The tonearm can be raised at any position, also for brief interruptions when
playing, by using the cue control lever (cueing in position ). The platter
continues to rotate in this case.
At the end of record, the tonearm is automatically repositioned back on the
tonearm post and the unit is switched off.
— You can also switch off the turntable by setting switch 6 to Stop or
setting the cueing lever 3 to position and repositioning the tonearm on
the tonearm rest.
Safety precautions
CAUTION!
To prevent the risk of fire or electrical damage, do not expose the device to
moisture or rain. Please do not open the device! Keep the packaging material,
such as plastic foils, away from children. Danger of asphyxiation by misuse.
Disposal of electrical appliances by consumers in private households within
the EU At the end ofits lifetime, do not throw the device away with the normal
household waste. Ask about the options for environmentally sound disposal at
the local authorities, at recycling centers, or where you purchased the
device.
**** This product complies with applicable EU regulations.
Technical data
Belt Drive|
---|---
Main voltage| 230 V/50 Hz 115 V/60 Hz
Line frequency| 50 / 60 Hz
Power equirement| 1,5 W
Platter speeds (rpm)| 33, 45
Wow and flutter| +/- 0,06/0,035 %
Signal-to-noise ratio (DIN 45500)
Rumpel unweighted signal-to-noise
Rumpel weighted signal-to-noise| 40 dB
62 dB
Effective tonearm length| 211 mm
Offset angle| 26°
Overhang| 19,5 mm
Tangential tracking error| 0,15°/cm Rad.
Cartridge| AT3600
Tracking force| 20 mN (2g)
Frequency range| 20 Hz – 20 kHz
Output| 3.5 mV/1000 Hz, 5 cm/sec.
Tracking capability| 60 um
Cartridge weight| 5,7g
Dimensions (WxHxD)| 430 x 365 x 130 mm
More info
www.rekkord-audio.com
Ask us
Technical questions: support@rekkord-audio.com
General questions: info@rekkord-audio.com
RECORDS Audio
a Division of AudioTuningVertriebs GmbH
Billing address:
Margaretenstrasse 98 A-1050 Vienna
AUSTRIA
Headquarters & Logistics:
Wirtschaftspark A5 Mistelbach/Wilfersdorf
Analogweg 1, 2130 Mistelbach
AUSTRIA
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>