DESKVIEW 061020 Mini Standing Desk Instruction Manual
- June 5, 2024
- DESKVIEW
Table of Contents
DESKVIEW 061020 Mini Standing Desk Instruction Manual
INSTALLATION
STEP 1 CLEAN:
Wet fingertips and wipe clean the rubber suction discs, leaving them slightly wet. Clean window with water and a microfiber towel
WARNING:
Ensure that the surface selected is (1) smooth, (2) flat, and (3) rated to
withstand the forces that will be placed upon it once Desk View is installed.
See website FAQ regarding tempered glass requirement.
STEP 2 GRIP:
Grip the bracket so your thumb and fingers are touching the edges of the
suction disc and the lever rests against your palm.
TIP:
Ensure that every part of the rubber suction disc contacts the surface and
that the disc does not overlap any joints or imperfections on the surface.
STEP 3 PRESS:
Check to see Desk View is level, then press firmly against the clean, flat
glass surface (see “Testing Non Glass Surfaces” on page 3 for testing other
materials).
STEP 4 SECURE:
With your palm, press down the lever. You should feel resistance as you engage the suction force.
TIP:
The resistance of the negative pressure generated must be clearly felt.
STEP 5 TEST:
Grab the working surface on each side – Pull Down and the Pull Away from the glass to ensure secure suction. Re-test in 5 minutes and then every 24 hours. If the required suction force has not been achieved, repeat steps 1-4 before using your DeskView.
WARNING:
The suction force may feel strong when initially tested, but impurities in the
mounting surface and dust, hair, or debris under the suction disc can slowly
allow air into the vacuum chamber, causing your DeskView to lose hold force
over time. Repeat Steps 1-5 every time the outside temperature changes
by>30°F.
Do not leave objects unattended on or below DeskView.
STEP 6 LOAD:
When placing objects, distribute weight equally on both sides of the top surface. Overweighting one side may result in your DeskView dipping or cause the suction disc to twist and lose hold force.
STEP 7 SEAL CHECK:
If you are able to see the back side of the rubber suction discs, you can verify a perfect seal by looking for a thick:, black band at every point along the rim of the rubber suction disc. Thin sections are indications of a compromised seal. Re-install if you notice a compromised seal.
ENJOY!
MAX. LOAD: 20 LBS.
MAX. WINDOW TEMPERATURE: 120°F
FOR TEMPERED GLASS ONLY
TESTING NON – GLASS SURFACES
IMPORTANT NOTICE:
DeskView is designed and tested for tempered, commercial, high-rise glass. The following testing procedures must be followed before using DeskView on any other surfaces to ensure strong, long-lasting suction force can be maintained.*
STEP A SAFETY:
Using pillows, blankets, or other soft items, create a safety area directly
below DeskView (1-6 inches below where DeskView will be tested) to protect
DeskView from damage.
HERE’S WHY:
If the non-glass surface allows air into the vacuum chamber, it will weaken
the suction force, causing DeskView to fall.
STEP B TEST INSTALLATION:
Following Installation Steps 1-5 on pages 1-2, install DeskView on the non- glass surface (avoiding grout and seams) 1-6 inches above the safety area. Test for secure install after 5 minutes and 24 hours.
TIP:
You must re-test after 5 minutes and 24 hours. The non-glass surface may
slowly allow air into the vacuum chamber so DeskView initially appears secure
but loses force. Do not place any items on Desk View while testing.
STEP C FINAL INSTALLATION:
If DeskView remains secure on the non-glass surface after 24 hours, follow installation Steps 1-S on pages 1-2 at the desired height.
WARNING:
Ensure the non-glass surface is rated to withstand the weight you will be
placing on DeskView. Do not use DeskView on any surface that fails Step B.
REMOVAL INSTRUCTIONS
STEP 1 REMOVE ITEMS:
Remove all items placed on DeskView’s working surface.
STEP 2 SLOWLY RELEASE LEVER:
Grip the bracket so your thumb and fingers are touching the edges of the
suction disc and the lever rests against your palm. To release the lever,
rotate your hand so your palm is facing up with your middle two fingers
touching the bottom of the lever. Slowly pull up on the lever with your middle
two fingers. Release the lever into your palm to allow for a slow release.
WARNING:
The Lever can release at high-speed. Avoid injury and damage to your DeskView
by keeping your palm on the Lever as you release with your middle two fingers.
DO NOT place your thumb on the Lever at any time.
STEP 3 BREAK SUCTION SEAL :
If DeskView cannot be removed after releasing the lever, then while
gripping the bracket as described in Step 2, slide your fingertip between the
glass and the rubber suction disc to release the suction force.
MAINTENANCE
- Always keep the rubber suction discs clear of oil, dust, hair and debris.
- Clean the rubber suction discs with water and a micro-fiber towel before every use.
- Check the rubber suction discs for possible deterioration. If rubber suction discs show damage, contact us at contact@shopdeskview.com and replace immediately.*
- DO NOT remove the top surface or try to replace the rubber suction discs or any other components without first receiving proper replacement instructions from us by contacting contact@shopdeskview.com
*DeskView offers FREE REPLACEMENT for
damaged rubber suction discs.
COPYRIGHT
Copyright© Abvious, LLC 2019.
Contents subject to revision without prior notice.
DeskView is a registered trademark of Abvious, LLC (the “Company”). All rights
reserved. No part of this manual may be reproduced, transmitted, transcribed,
or translated into any language, in any form or by any means, without the
prior written consent of the Company.
DISCLAIMER
The company does not warrant the the product will work properly in all
environments and applications, and makes no representations or warranties,
either implied or express, with respect to the quality, performance, or
fitness for a particular purpose.
The company shall not be responsible for products found to be defective as a result of misuse, mishandling, or neglect.
Information contained in this manual is subject to change without notice and the Company reserves the right to make improvements to this manual and/or to the products described in this manual, at any time without notice.
If you would like an electronic copy of the most up-to-date manual or if you find information contained in this manual that is inaccurate, misleading, or incomplete, please contact us at contact@shopdeskview.com
THE COMPANY MAKES NO OTHER REPRESENTATIONS OR WARRANTIES OTHER THAN THOSE SPECIFIED IN THIS MANUAL, OF ANY KIND WHATSOEVER, EXPRESS OR IMPLIED, AND WARRANTIES OF MERCHANTABILTIY AND FITNESS FORA PARTICULAR PURPOSE ARE HEREBY DISCLAIMED BY THE COMPANY AND EXCLUDED FROM THE TERMS OF SALE.
Please follow these instructions for the best
performance and long life of your
DeskView.
Made in China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>