RYOBI PSBDD01 One+ Brushless Compact 1/2 Inch Drill/Driver Owner’s Manual

RYOBI PSBDD01 One+ Brushless Compact 1/2 Inch Drill/Driver SAFETY

WARNINGS

Save all warnings and instructions for future reference. The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery- operated (cordless) power tool.

WORK AREA SAFETY

•  Keep work area clean and well lit. Cluttered or dark areas invite accidents.
•  Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
•  Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

ELECTRICAL SAFETY

•  Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
•  Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
•  Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
•  Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
•  When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
•  If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply. Use of a GFCI reduces the risk of electric shock.
•  Use this product only with batteries and chargers listed in tool/appliance/battery pack/charger correlation supplement 987000-432.

PERSONAL SAFETY

•  Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
•  Use personal protective equipment. Always wear eye protection. Protective equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.
•  Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
•  Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
•  Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
•  Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewelry or long hair can be caught in moving parts.
•  If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
•  Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
•  Do not wear loose clothing or jewelry. Contain long hair. Loose clothes, jewelry, or long hair can be drawn into air vents.
•  Do not use on a ladder or unstable support. Stable footing on a solid surface enables better control of the power tool in unexpected situations.

POWER TOOL USE AND CARE

•  Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
•  Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
•  Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
•  Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
•  Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
•  Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
•  Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
•  Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

BATTERY TOOL USE AND CARE

•  Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
•  Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
•  When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
•  Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
•  Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, EXPLOSION or risk of injury.
•  Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 265 °C may cause explosion.
•  Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the BATTERY and increase the risk of fire.

SERVICE

•  Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
•  Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.
•  When servicing a power tool, use only identical replacement parts. Follow instructions in the Maintenance section of this manual. Use of unauthorized parts or failure to follow Maintenance instructions may create a risk of shock or injury

DRILL SAFETY WARNINGS

•  Use auxiliary handle(s), if supplied with the tool. Loss of control can cause personal injury.
•  Brace the tool properly before use. This tool produces a high output torque and without properly bracing the tool during operation, loss of control may occur resulting in personal injury.
•  Hold power tool by insulated gripping surfaces, when performing an operation where the cutting accessory may contact hidden wiring. Cutting accessory contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
•  Know your power tool. Read operator’s manual carefully. Learn its applications and limitations, as well as the specific potential hazards related to this power tool. Following this rule will reduce the risk of electric shock, fire, or serious injury.
•  Always wear eye protection with side shields marked to comply with ANSI Z87.1. Following this rule will reduce the risk of serious personal injury.
•  Protect your lungs. Wear a face or dust mask if the operation is dusty. Following this rule will reduce the risk of serious personal injury.
•  Protect your hearing. Wear hearing protection during extended periods of operation. Following this rule will reduce the risk of serious personal injury.
•  Battery tools do not have to be plugged into an electrical outlet; therefore, they are always in operating condition. Be aware of possible hazards when not using your battery tool or when changing accessories. Following this rule will reduce the risk of electric shock, fire, or serious personal injury.
•  Do not place battery tools or their batteries near fire or heat. This will reduce the risk of explosion and possibly injury.
•  Do not crush, drop or damage battery pack. Do not use a battery pack or charger that has been dropped or received a sharp blow. A damaged battery is subject to explosion. Properly dispose of a dropped or damaged battery immediately.
•  Batteries can explode in the presence of a source of ignition, such as a pilot light. To reduce the risk of serious personal injury, never use any cordless product in the presence of open flame. An exploded battery can propel debris and chemicals. If exposed, flush with water immediately.
•  Do not charge battery tool in a damp or wet location. Following this rule will reduce the risk of electric shock.
•  For best results, your battery tool should be charged in a location where the temperature is more than 50°F but less than 100°F. To reduce the risk of serious personal injury, do not store outside or in vehicles.
•  Under extreme usage or temperature conditions, battery leakage may occur. If liquid comes in contact with your skin, wash immediately with soap and water. If liquid gets into your eyes, flush them with clean water for at least 10 minutes, then seek immediate medical attention. Following this rule will reduce the risk of serious personal injury.
•  Save these instructions. Refer to them frequently and use them to instruct others who may use this tool. If you loan someone this tool, loan them these instructions also to prevent misuse of the product and possible injury.

SYMBOLS

ASSEMBLY

Do not use this product if it is not completely assembled or if any parts appear to be missing or damaged. Use of a product that is not properly and completely assembled or with damaged or missing parts could result in serious personal injury Do not attempt to modify this product or create accessories or attachments not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.

APPLICATIONS
You may use this product for the purposes listed below: Drilling in all types of wood products (lumber, plywood, paneling, composition board, and hard board), ceramics, plastics, fiberglass, laminates, and metals; driving screws into wood and drywall with screwdriver bits

OVERLOAD PROTECTION
When the tool is forced or the motor is overloaded, the tool will automatically shut off. To reset the tool, release the trigger and resume operation. If the tool still does not resume operation, remove and reinsert the battery. Do not force the tool.
HIGH-TEMPERATURE PROTECTION
Li-ion battery packs are equipped with a high-temperature protection feature that automatically deactivates the tool when it is overheated. To resume operation, allow the tool to cool and then squeeze the trigger.

INSTALLING/REMOVING BELT HOOK OR BIT HOLDER (NOT INCLUDED)

• The belt hook and bit holder are interchangeable. They may be installed on either side of the base.
•  Align hole in belt hook or bit holder with hole in tool’s base.
•  Install screw to secure belt hook or bit holder in place.
•  To uninstall, remove screw and then belt hook or bit holder.

OPERATION

VARIABLE SPEED SWITCH TRIGGER

• The variable speed switch trigger delivers higher speed with increased trigger pressure and lower speed with decreased trigger pressure.
• To turn the drill ON, depress the switch trigger. To turn it OFF, release the switch trigger and allow the chuck to come to a complete stop.
• NOTE: A whistling or ringing noise coming from the switch during use is a normal part of the switch function.
• NOTE: Running at low speeds under constant usage may cause the drill to become overheated. If this occurs, cool the drill by running it without a load and at full speed.

DIRECTION OF ROTATION SELECTOR  (FORWARD/REVERSE/CENTER LOCK)
Set the direction of rotation selector in the OFF (center lock) position to lock the switch trigger and help prevent accidental starting when not in use. Position the direction of rotation selector to the left of the switch trigger for forward drilling. Position the selector to the right of the switch trigger to reverse the direction.
NOTE: The drill will not run unless the direction of rotation selector is pushed fully to the left or right

INSTALLING/REMOVING BATTERY PACK

•  Lock the switch trigger.
•  Insert the battery pack into the product as shown.
•  Make sure the latches on each side of the battery pack snap into place and that battery pack is secured in the product before beginning operation.
•  Depress the latches to remove the battery pack.
• For complete charging instructions, see the operator’s manuals for your battery pack and charger

INSTALLING/REMOVING BITS

• The arrows on the keyless chuck indicate which direction to rotate the chuck body to tighten or release the drill bit.
• Do not use a wrench to tighten or loosen the chuck jaws.
•  To install bits, lock the switch trigger.
•  Open or close the chuck jaws until the opening is slightly larger than the bit size you intend to use.
•  Raise the front of the drill slightly and insert the drill bit
•  Rotate the chuck sleeve to close and tighten the chuck jaws.
•  To remove bits, lock the switch trigger and open the chuck jaws.

LED LIGHT

• The LED light, located on the front of the tool base, illuminates when the switch trigger is depressed.
• If the drill is not in use, the time-out feature will cause the light to start fading and then shut off.
• The LED light illuminates only when there is a charged battery pack in the tool.

TWO-SPEED GEAR TRAIN

•  Select low speed (1) for applications requiring higher power and torque, such as driving screws and drilling in metal.
•  Select high speed (2) for fast drilling or driving applications or for drilling in wood or masonry

ADJUSTING TORQUE

• Rotate the adjustment ring to the proper torque setting for the type of material and size of screw you are using.
•  1 – 4 For driving small screws
•  5 – 8 For driving screws into soft material
•  9 – 12 For driving screws into soft and hard materials
•  13 – 16 For driving screws into hard wood
•  17 – 23 For driving large screws

DRILLING/DRIVING SCREWS

•  Check the direction of rotation selector for the correct setting (forward or reverse).
•  Use low (1) speed for high torque applications and high (2) speed for fast drilling or driving applications. Refer to Two-Speed Gear Train and Adjusting Torque.
•  Secure the workpiece in a vise or with clamps to keep it from turning as the bit rotates.
•  Hold the drill firmly and place the bit at the point to be drilled, or where the screw is to be driven.
•  Depress the switch trigger to start the drill.
•  Move the bit into the workpiece, applying only enough pressure to keep the bit cutting or driving the screw.
• Do not force the drill or apply side pressure to elongate a hole. Let the tool do the work.
•  With hard, smooth surfaces, use a center punch to mark the desired hole location. This will prevent the bit from slipping off-center as the hole is started.
•  If the bit jams in the workpiece or if the drill stalls, stop the tool immediately. Remove the bit from the workpiece and determine the reason for jamming.
• NOTE: This drill has an electric brake. When the switch trigger is released, the chuck stops turning.

WOOD AND METAL DRILLING

• For maximum performance, use high speed steel bits for wood or metal drilling.
• Select drilling mode. Begin drilling at a very low speed to prevent the bit from slipping off the starting point.

Wood Drilling

•  Increase the speed as the drill bit bites into the material.
•  When drilling through-holes, place a block of wood behind the workpiece to prevent ragged or splintered edges on the back side of the hole.

Metal and Steel Drilling

•  Use a light oil on the drill bit to keep it from overheating. The oil will prolong the life of the bit and increase the drilling action.
•  Maintain a speed and pressure which allows cutting without overheating the bit. Applying too much pressure will:
•  Overheat the drill;
•  Wear the bearings;
•  Bend or burn bits; and
•  Produce off-center or irregular-shaped holes.
•  When drilling large holes in metal, start with a small bit, then finish with a larger bit

MAINTENANCE

GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, dust, oil, grease, etc.

TROUBLESHOOTING

References

• REIMAGINE WITH RYOBI - RYOBI Tools
• Herramientas Eléctricas Ryobi

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>