VATOS YD-218 Remote Control Helicopter Instruction Manual

June 11, 2024
Vatos

VATOS logo YD-218
Age: 14+
INSTRUCTION MANUAL
3.5CH Remote Control HelicopterVATOS YD-218 Remote Control
Helicopter

YD-218 Remote Control Helicopter

  • Technical specification:
  • Dimension: 260 X 130 X 45mm
  • Total weight: 68 g
  • Control frequency: 2.4Ghz
  • Remote control range: 30-40 M
  • Flight time: 6 minutes
  • Charge time: 60 minutes

Battery/charging

  1. heli battery (built-in): 3.7V/300mAh Li-Polymer battery
  2. remote control battery: Standard “AAA” x 3 PCS
  3. charge method: USB charging cable

Please read this instruction manual carefully before operating the heli to avoid possible damage to the heli or people.
Pull the throttle to the highest point and then to the lowest to unlock the power protection.

Parts name

VATOS YD-218 Remote Control Helicopter - Parts nameVATOS YD-218 Remote Control Helicopter - Parts name
2

Battery installing and charging

Battery installingVATOS YD-218 Remote Control Helicopter -
Battery Charging

  1. Disconnect the power wire from the heli ,and connect to the USB in the right polarity.
  2. USB charger must be connected to computer USB port or other standard port device correctly.If the USB indicator light is red,the battery is charging.The indicator light turns green when the battery is fully charged.

VATOS YD-218 Remote Control Helicopter - Charging NOTE:

  1. If the indicator on the remote control keeps flashing when maneuvering the power controller, this indicates that the batteries are low; they must be replaced.
  2. When done charging, please pull out the charger.
  3. Other USB power sources include LCD TV, DVD, cell phone, etc.

Operating helicopter

Install and connect the battery in the helicopter. The indicator lights on the top of the helicopter will flash.
Then turn on the remote, pull the throttle stick to the highest point and then to the lowest to connect with the helicopter. When the color lights on the circuit board keep lighting, this indicates the frequency is successfully matched.

  • Put the helicopter on the floor with the tail facing the pilot.
  • Press the one key take-off/landing to start flying.
  1. Going up and going down
    Slowly push up the throttle stick, and the rotor will spin faster and faster. When pulling down the throttle stick, the helicopter will gradually land on the floor. If it spins in the air, press the opposite direction trimmer to stable the helicopter.VATOS YD-218 Remote Control Helicopter - Going up and
going down

  2. Turning left and right
    Turn the throttle stick to right, and the heli flies right.
    Turn the throttle stick to left, and the heli flies left.VATOS YD-218 Remote
Control Helicopter - Turning left and right

  3. Flying forward
    Pull the thorttle stick up, and the heli flies forward.VATOS YD-218 Remote
Control Helicopter - Flying forward

  4. Flying backward
    Pull the thorttle stick down, and the heli flies backward.VATOS YD-218
Remote Control Helicopter - Flying backward

NOTE: When operating the heli to fly forward or backward, it might spin; the trimmer can be used to adjust the direction.

  1. If the heli spins in the air even without touching the throttle stick, the trimmer on the remote can be adjusted till the heli is stabilized.
  2. If the heli spins counter-clockwise, turn the trimmer clockwise to stabilize it.VATOS YD-218 Remote Control Helicopter - trimmer clockwise
  3. If the heli spins clockwise, turn the trimmer counter-clockwise to stabilize it.VATOS YD-218 Remote Control Helicopter - trimmer clockwise 2

Operation instructions:

  1. Turn the helicopter power on; the red indicator flashes meaning it is ready to fly.
  2. Turn the remote on and the light on it flashes. This indicates that the throttle is locked in protect mode. Pull the throttle to the highest point and then to the lowest to unlock.
  3. Locking function: In any situation of falling off or crashing, the power in the helicopter will be turned off automatically. To unlock it, pull the throttle to the highest point and then to the lowest; this protects the motor and receiver board from over-heating.
  4. Heli battery over-discharging protection: The heli descends as the power gets lower.
    When the power is below 3.0 V, the power is turned off automatically so the heli will not crash on the floor due to low power. This helpsto protect the battery and extends its life span, and makes the battery longer lasting and more powerful.

Operation tip

  • Do not fly the heli in direct sunshine or strong light; this affects the flight.
  • Do not cover the transmitting light on the remote; this affects infrared signal emitting.
  • Do not paste any paper on the heli; this affects infrared signal receiving.
  • Do not use other USB chargers to charge the heli.
  • Do not mix new and old batteries in the remote.
  • Do not mix chargeable and nonchargeable batteries in the remote.

Flying environment

  • Indoor with smooth air flow. Note: cold air flow from AC etc affects flight.
  • Open area. It is suggested that you fly the heli in an area at least 6 feet (width) 9 feet (length)3 feet (height).
  • Safe area. It is strongly recommended that you fly the heli in an area with no AC, fans, lamps or hazardous objects, etc.

The heli comes with built-in Li-Poly batter; please note below:

  • Do not put the heli in a high temperature environment, such as flame or electronic heating device or the batter will explode or be damaged.

  • Do not put the heli under water or operate and store in a moist environment.
    The heli must be kept in a dry environment.

  • Do not leave the heli unattended when charging.

  • Do not charge the heli on flammable objects such as carpet.

@vatostoys
www.vatostoys.com
info@vatostoys.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals