Shenzhen Leqi Network Technology SG-20 Side Handle with Wireless Control for Cellphone User Manual
- June 5, 2024
- Shenzhen Leqi Network Technology
Table of Contents
Shenzhen Leqi Network Technology SG-20 Side Handle with Wireless Control for Cellphone
Operation Guide
| Wireless Side Handle | Side Handle / SG-20 |
|---|---|
| Power On | Press the camera button for 3 seconds to power on, it will flash for |
4 seconds to enter into the pairing status with indicator light flashes
Power Off| Press the camera button for 3 seconds to turn off the power, and
the indicator light will turn off
Unpaired Status| Indicator light flashes
Paired Connection Status| After pairing and connecting, the indicator light is
off; It enters standby status without operation for 10 minutes
Standby S Status| After powering on, in the status of no pairing connection,
it will automatically shut down if there is no operation for 5 minutes
Camera Button| Shortly press the camera button, the indicator light flashes,
start shooting
Charging Status| Plug in the charging cable, the red light is constantly on,
until fully charged, the blue light is constantly on
Working Status| When the battery level is 20% and above: each indicator light
is displayed in blue light
When the battery level is less than 20%: each indicator light is displayed in
red
Warnings
- Please read this User Manual carefully.
- Do not use the product in water because it is not dust or water proof.
- Do not let the product fall to the ground, be hit or suffer violent impact.
- Be sure to power the product off when it is not in use.
- Never remove the non-detachable lithium battery without permission.
- Since there are some hazardous substances in the battery, please do not discard it. Instead, dispose of the product that is damaged or will never be used according to the waste management measures.
Intended Use
- Please read this User Manual carefully, especially the “Warnings”.
- Please use or store the product in the environment mentioned herein.
- It will be regarded as an improper use when the users are not correctly follow the user manual or use the product under the specific working condition.
Installation Guide
- Remove the two screws on the connector
- Put the connector into the side of the handle
- Lock the connector on the handle with the two removed screws
Tech Specs
| Battery Type | Polymer Lithium Ion Battery |
|---|---|
| Rated Capacity | 100mAh |
| ated Voltage | 3.7V |
| dby Current | 1.5 – 2uA |
| Maximum Charge Current | 100mA |
| Standby Charge Current | 20mA |
| Upper Limit Charge Voltage | 4.25V |
| Maximum Discharge Current | 100mA |
| Standby Discharge Current | 20mA |
| Discharge Cut-Off Voltage | 3V |
| Temperature Range | 0℃-45℃ |
| Wireless Distance | 15m |
| Wireless Frequency | 2.4G（2402 – 2480MHZ） |
FCC Caution
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. This
device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation. This device and its antenna(s) must not be
co-located or operating in conjunction with any other antenna or transmitter.
NOTE:
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications
. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF Exposure guidelines, the 20cm is the minimum distance that has to be maintained between your body and the device.
FCC ID: 2AZWI-3838LEQI
Manufacturer: Shenzhen Leqi Network Technology Co., Ltd.
Add: 1st Floor, Building 9, Yazhou Industrial Park, Bantian,Longgang,
Shenzhen, Guangdong, China.
ISED Statement
English: This device contains licence-exempt transmitter(s)/receiver(s) that
comply with Innovation, Science and Economic Development Canada’s licence-
exempt RSS(s). Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
– 3 (b) / nmb – 3 (b). This device meets the exemption from the routine
evaluation limits in section 2.5 of RSS 102 and compliance with RSS 102 RF
exposure, users can obtain Canadian information on RF exposure and compliance.
The device has been evaluated to meet general RF exposure requirement. The
device can be usedin portable exposurecondition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>