KARACHI STATIONER FOAMA Touchless Hand Soap Dispenser Instructions
- June 5, 2024
- KARACHI STATIONER
Table of Contents
KARACHI STATIONER FOAMA Touchless Hand Soap Dispenser
OVERVIEW
IMPORTANT
- DO NOT IMMERSE in water or rinse under a stream of water.
- DO NOT OVERFILL bottle and keep upright to prevent liquid damage to batteries.
- DO NOT FILL WITH EXFOLIANTS. Do not use with mouthwash, or liquid soaps with granules, abrasives or microbeads. Traditional liquid soaps must be diluted. Do not fill with thick fluids or lotion. For best results, use foaming Soaps.
- TURN OFF prior to handling to avoid unwanted dispensing.
SET UP
Inseit 4x new AA (1.5v) batteries from the same package.
Add foaming solution to the bottle. Always replace the bottle plug and wipe the top of the bottle dry. Do not overfill and assemble carefully.
To turn on, touch & hold or 2 seconds until the solid green light flashes 3 times. Repeat to turn FOAMA off, as needed, a red light will flash and then become solid momentarily once FOAMA is off.
Place your hand under the spout to trigger the pump. Once liquid is added, trigger the pump until foam appears.
FOAMING SOAPS
FOAMA produces excellent foam with a variety of specially formulated foaming soaps. Use these for best results and easy refills.
DILUTING SOAPS
FOAMA works well with most non-granular, diluted liquid soaps. Each soap varies in formulation and it may be necessary to try other soaps for better results. When diluting liquid soaps with water, the following mixing guide will helpyou find the optimal ratio.
MIXING GUIDE
To minimize waste, mix a half bottle and then test the foam. Adjust as necessary and ensure the underside of the pump is kept dry. Swirl bottle to mix, do not shake.
Ideally, the foam will hold its shape well without any large bubbles. Some small bubbles are okay.
If the foam seems light, frothy and doesn’t clean well, add a small amount of of soap to give the foam more structure.
DISPENSING
Place hand under FOAMA’s spout to activate the touchless sensor. A green light is shown while the pump runs.
Wait for the cycle to finish or lower hand away from the sensor to stop the cycle early.
Quickly double tapto activate the pump and dispense a pre-set amount of foam. This feature is disabled by LOCK and unaffected by VOLUME setting.
When the battery power begins to run low, a red light will flash while pump is dispensing. New batteries may be required soon.
VOLUME
FOAMA always defaults to the lowest volume after turning on/off. Briefly touch to adjust the volume. The LED will quickly blink green 1, 2 or 3 times to indicate the new volume setting.
While FOAMA is ON, lock touch key by holding for 6 seconds until a green light is briefly shown. Repeat to unlock. When locked, only touchless operation is possible and no other changes can be made. Disable LOCK to power off. Opening the battery cover will reset LOCK.
- FOAMA is only splash resistant when upright and fully assembled. Do not immerse in water. Wipe with a soft damp cloth to clean.
- Water spray and droplets can trigger the 10 touch button.
- Enable LOCK or move FOAMA away from water spray.
- IF FOAMA will not turn on, ensure the battery chamber is dry and free of corrosion. If liquid enters the battery chamber, wipe out all liquid and leave dissembled to air dry. New batteries may be required.
- If FOAMA frequently turns off, or will turn on but will not pump, thoroughly clean any light corrosion otf of the batteries or replace the batteries. Battery life varies by battery brand and usage
- Please Note: Some creamy soaps may separate after diluting causing inconsistent foam texture. Consider trying a different soap. Rinse out bottle when changing soaps
1 YEAR MANUFACTURER’S WARRANTY
The FOAMA Touchless Soap Dispenser is guaranteed to be free of manufacturing defects for a period of 1 year from the original date of purchase. Better Living Products will replace the entire unit or any component deemed by the company to be defective in manufacture, at no charge, during the warranty period. Shipping Is extra.