Pyle PTA24BT 250W 2-Channel Compact Bluetooth Home Audio Amplifier-Complete Features/Instruction Guide

Pyle PTA24BT 250W 2-Channel Compact Bluetooth Home Audio Amplifier

Specifications

• POWER OUTPUT: 250W
• TOTAL HARMONIC DISTORTION 1 KHZ RATED POWER: 0.3%
• INPUT SENSITIVITY 1 KHZ, 4 OHM RATED POWER:   AUX 1: 180mV
• AUX 2: 180mV
• AUX IN: 200mV
• MIC: 6mV
• SIGNAL TO NOISE RATIO,1 KHZ, 4-OHM RATED POWER: AUX 1: 81dB
• AUX 2: 81dB
• AUX IN: 81dB
• MIC: 68dB
• BASS 100HZ: ±10dB
• TREBLE 10KHZ: ±10dB
• FREQUENCY RESPONSE, 1KHZ 1W, +/-3DB (8-0HM): 20Hz-20KHz
• POWER REQUIREMENT: 120VAC60Hz or 230V AC 50Hz

Introducion

For streaming audio, use Bluetooth. Talk-over function with built-in microphone Remote control is included.

WARNING

This symbol is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure, it may have sufficient magnitude to constitute a risk of electric shock to persons. This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

FEATURES AND CONTROLS

FRONT PANEL

BACK PANEL

1. MAIN POWER ON SWITCH
   Switch ON or OFF The amplifier by using this switch.

2. ECHO CONTROL
   Turn the knob to adjust the MIC echo level.

3. MIC 1 VOL & MIC 2 VOL
   Turn the knob clockwise to increase the MIC volume.

4. MIC 1 & MIC 2 INPUT JACK
   KARAOKE MIC connected to these jacks.

5. & 6. BASS AND TREBLE TONE CONTROL
   Let’s you boost or attenuate bass and treble for the desired sound.

6. MASTER VOLUME
   Adjusts main audio system volume level.

7. AUDIO SOURCE SWITCH
   Audio Source Switches between AUX1 input, AUX2 input, BT/FM/USB/SD

8. INDEPENDENT CHANNEL VOLUME CONTROLS
   Adjusts audio volume levels for connected input(s).

9. SD/MMC SOCKET FOR PLAYING SD/MMC CARDS
   

10. USB CHARGE PORT & USB READER FUNCTION
    USB port for smartphone charging and USB reader function.

11. BUTTONS FOR BLUETOOTH/MP3 (USB AND SD) FUNCTION CONTROL
    MODE Button: For audio selection like BLUETOOTH/USB/SD/LINE IN
    PLAY/PAUSE BUTTON: Play and Pause control button
    PREV/NEXT: Quick backward or next song

12. BLUE LED DISPLAY WINDOW FOR MP3/BLUETOOTH FUNCTION

13. HEADPHONE CONTROL
    5mm headphone input jack with independent rotary volume control.

14. LINE INPUT AUX/CD IN
    Connect the MP3 Device (player) sources such as PC (CD ROM), laptop, Walkman, iPod and mobile phone

15. MICROPHONE TALK-OVER
    The switch-activated function allows for direct audio integration with a connected microphone (MIC1).

16. AC IN POWER CORD
    Connect to AC 110V/60Hz or 220V/50Hz

17. PUSH TYPE SPEAKER L/R TERMINALS
    Connect the speaker wires directly to the amplifier

18. STEREO SUBWOOFER OUTPUT
    Connect to subwoofer system from these terminals

19. STEREO RECORDING FUNCTION OUTPUT

20. RCA L/R LINE INPUT
    Connect to desired LINE input sources.

21. 110V/220V SWITCH
    According to power voltage, push this button to the 110V or 220V correct station.

22. BLUETOOTH ANTENNA
    Bluetooth receiver

REMOTE CONTROL FUNCTION

1. Power ON Button
2. Play/Pause Button
3. Equalizer Button
4. Repeat Song Button
5. MODE: Menu Control Button

Press to select BT/USB/SD/LINE IN etc. audio input

6. MUTE Button
7. Previous Song Button
8. Next Song Button
9. Volume + and Volume – Buttons
10. USB/SD Switch Button
11. Number Buttons for Song Selection

BLUETOOTH OPERATION INSTRUCTION

External devices which have a built-in Bluetooth feature can be connected to this amplifier wirelessly to play through the amplifier’s speakers. If your amp is connected to speakers, you will hear audible tones which will help for connecting.

1. At first be sure that the amplifier is powered on, and turn the volume to low. Please remember to connect the Bluetooth Antenna at the back panel for better receiving signal.
2. Press the BT/Line button switch in on the front panel, you will hear the voice “POWER ON” and also “PAIRING”, and then the unit is automatically ready to pair with your external device.
3. Turn on the Bluetooth of your external device.
4. Search for available Bluetooth devices and make sure to be within range of your amp, and wait for your device to select “BT-RY” on the pairing devices lists of Bluetooth networks.
5. Once connected you will hear a voice say, “Your Device is Connected”, the Bluetooth pairing is successful and connected.
6. You can now play music on your external device through the amplifier.

CARING FOR YOUR PYLE AMPLIFIER

Your Pyle Amplifier is an example of superior design and craftsmanship. The following suggestions will help you care for your amplifier so you can enjoy years of use:

• Keep the amplifier dry. If it gets wet, wipe immediately.
• Use the amplifier only in well-ventilated installations.
• Handle the amplifier away from dust and dirt.
• Wipe occasionally with a damp cloth to keep it looking new. Do not use harsh chemicals, solvents, or detergents!

IMPORTANT

REPLACING A FUSE

This amplifier requires a fuse with the proper rating for protection from power surges and short circuits. If the amplifier suddenly turns off or would not turn on, the fuse is properly blown.

• Let the amplifier cool down and see if it starts again before you assume a fuse needs to be replaced.
• Unplug the amplifier from the AC outlet.
• Turn the fuse holder cap and pull out the cap.
• Remove the old fuse and replace it with an identical one.

CAUTION
Never use a fuse with a higher rating

TROUBLESHOOTING

NO POWER| The fuse might be blown| Check the amplifier’s fuse and replace it if necessary.
---|---|---

NO SOUND

| Sound source or speakers may not be connected properly| ****

Check all connections

 | Master volume control may be set to a minimum| Adjust the volume control to a higher setting
The speaker’s wire might have the wrong impedance| Make sure that the speakers that you have connected to the amp are matching in impedance

The amplifier is shutting down or powering off

| Turn the amplifier off and let it cool, make sure that the amplifier is properly ventilated, and then tum it back on
Feedback| Microphone and speakers are too close together| Reposition the microphone and speakers

Frequently Asked Questions

• How can I get my Pyle Bluetooth AMP to work?
  STEP-BY-STEP GUIDE TO CONNECTING WITH A BLUETOOTH DEVICE
  Enter Wireless BT mode by pressing the MODE button under the LCD display panel. C. Select the Wireless BT name “Pyle Speaker” and wait for the device to pair.

• What is the procedure for connecting my phone to Pyle?
  If you go to your iPhone or Android’s Bluetooth settings, you’ll see Pyle Audio. Click on it and input your pairing code, which is 0000.

• What is the best way to attach Pyle speaker wire?
  Connect the speaker cables to the positive (+) and negative (-) terminals on the left and right speakers, respectively. 2. Connect the positive (+) and negative (-) wires from the left and right speakers to the amplifier’s SPEAKER LEFT and SPEAKER RIGHT terminals for each channel.

• How do you get the Pyle Speaker to work?
  You must plug the Pyle speaker into an outlet and click the power button to turn it on.

• Why isn’t my Pyle Speaker working?
  Make sure the Bluetooth feature on YOUR device is turned on. 5. See “Pairing the Speaker with a Bluetooth Enabled Device” for more information on how to repeat the pairing process. My Bluetooth device will not connect to the Bluetooth Speaker.

• What is the positive side of the speaker wire?
  The positive wire is usually red, whereas the ground, or negative, is black. Most speaker wires, on the other hand, do not support color. The good news is that when it comes to speakers, it doesn’t really matter which one you choose as your positive and which one you choose as your negative as long as you’re consistent.

• What is the best way to charge a Pyle Bluetooth speaker?
  Connect the power cable to the amplifier system by plugging it into the socket. Turn the amplifier on. When the Power Indicator turns red, it means it’s time to take action. When the RECHARGE LED goes red during charging, it implies the battery is almost full, and it turns off when fully charged.

• Are Pyle speakers Bluetooth-enabled?
  With the Pyle Tube BoomBox Speaker, you can enjoy portable and powerful music playback! All of today’s latest gadgets, including Smartphones, Tablets, and Laptops, may effortlessly connect and play music via Bluetooth wireless audio streaming.

• What is a Bluetooth amplifier and how does it work?
  An earpiece is one of the most frequent forms of Bluetooth® amplifiers. The earpiece is worn near the ear and amplifies the output of an electrical signal that contains audio data. After being amplified, the signal is delivered to the speaker, which allows the person wearing the earpiece to hear the audio

• What is the best way to utilize a frequency 2.0 Bluetooth speaker?
  In order to use Bluetooth, you must first enable it in your device’s settings. When you turn on the speaker, the name (Frequency 2.0) will appear on your mobile once it has been synced. To link to a name, tap it.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>