XPOtool 61952 Cable Stripping Machine User Manual
- June 5, 2024
- XPOtool
Table of Contents
XPOtool 61952 Cable Stripping Machine
Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps, and technical data can differ insignificantly. Updating the documentation If you have suggestions for improvement or have found any irregularities, please contact us. The information contained in this document may alter at any time without previous notice. It is prohibited to copy or spread any parts of this document in any way without prior written allowance. All rights re-served. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown. Even though, the WilTec Wildanger Technik GmbH has undergone biggest possible efforts to ensure that the operating manual is complete, faultless, and up to date, mistakes cannot be entirely avoided. If you should find a mistake or wish to make a suggestion for improvement, we look forward to hearing from you. Send an e-mail to: service@wiltec.info or use our contact form: https://www.wiltec.de/contacts/ The most recent version of this manual in various languages can be found in our online shop via: https://www.wiltec.de/docsearch Our postal address is: WilTec Wildanger Technik GmbH 52249 Eschweiler Germany To return orders for exchange, repair, or other purposes, please use the following address. Attention! To allow for a smooth execution of your complaint or return, it is important to contact our customer service team before returning the goods.
- Returns Department
- WilTec Wildanger Technik GmbH
- 52249 Eschweiler
- E-mail:service@wiltec.info
- Tel: +49 2403 55592–0
- Fax: +49 2403 55592–15
Introduction
Thank you for purchasing this quality product. To minimize the risk of injury
we urge that our clients take some basic safety precautions when using this
device. Please read the operation instructions
carefully and make sure you have understood its content. Keep these operation
instructions safe.
Safety precautions
The owner and/or user must have read and understood the operating instructions before using the device. Instructed personnel should be careful, competent, trained, and qualified in the safe handling of the equipment used. Warnings should be read and understood.
-
Do under no circumstances and at no point touch the machine with your fingers, as this can
lead to serious injuries. -
We recommend the use of safety gloves to minimise the risk of injury.
-
Observe the applicable occupational safety and accident prevention regulations.
-
This equipment is not intended for use by people (including children) with reduced physical, sensory, or mental abilities or people without appropriate experience or knowledge, unless they are supervised by a person responsible for their safety or have received prior instruction in the use of the equipment.
-
Children must be supervised to ensure that they do not play with the equipment.
-
Use a hair net for long hair.
-
In addition, the local accident prevention regulations, and general safety regulations applicable to the area of application of the device must be observed.
-
If you have long hair, use a hair elastic and tie your hair up.
-
In addition, the local accident prevention regulations applicable to the area in which the device is used and the general safety regulations must be observed.
Operation
- First, make sure to adjust the distance between the blade and the shaft according to the size of the cable that is to be stripped. Please make sure that the device is set to only strip the insulating layer without damaging the inner conductors.
- Thread the cable into the feed and adjust the same until the cable can be pulled through without shifting the inside fixture.
- Use the hand crank to strip the cable of its insulation layer by pulling it past the blade. Alternatively, the hand crank can be removed from the device and can be replaced with a drill by utilising the drill connector bit.
- Should the device be unable to separate the cable from its insulation, it might be due to one of the following reasons:
- The diameter of the cable is too small.
- The blade is not positioned in the centre and has therefore to be adjusted.
- The blade has gotten dull and needs to be sharpened/replaced.
Components and their names
Technical data
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>