XPOtool 62739 12V Wind Generator User Manual

XPOtool 62739 12V Wind Generator

Please read and follow the operating instructions and safety information prior to initial operation. Technical changes reserved! Illustrations, functional steps, and technical data may deviate insignificantly due to continuous further developments. https://www.XPOtool.com Item 62739, 62740 Page 2 The Tool Experts 05 2022-1 The information contained in this document may alter at any time without prior notice. No part of this document may be copied or otherwise duplicated without prior written consent. All rights reserved. WilTec Wildanger Technik GmbH cannot be held liable for any possible mistakes in this operating man-ual, nor in the diagrams and illustrations shown. Although WilTec Wildanger Technik GmbH has made every possible effort to ensure that this operating manual is complete, accurate, and up-to-date, errors cannot be ruled out entirely. If you have found an error or wish to suggest an improvement, we look forward to hearing from you. Send us an e-mail to:  service@wiltec.info or use our contact form: https://www.wiltec.de/contacts/ The most recent version of this manual in several languages can be found in our online shop:  https://www.wiltec.de/docsearch Our postal address is: WilTec Wildanger Technik GmbH  52249 Eschweiler Germany To return your goods for exchange, repair, or other purposes, please use the following address. Atten-tion! To allow for a trouble-free complaint or return, it is important to contact our customer service team before returning your goods.Retourenabteilung WilTec Wildanger Technik GmbH  52249 Eschweiler Germany  E-mail:service@wiltec.info Phone: +49 2403 55592–0 Fax: (+49 2403 55592–15)

Introduction

Thank you for choosing to purchase this quality product. To minimise the risk of injury, we ask you to always take some basic safety precautions when using this product. Please read this operating manual carefully and make sure that you understand it. Keep these operation instructions in a safe place.

Safety instructions

Attention!
A rotor in movement is very dangerous.

• The rotor blades are made of stable nylon fibres. With strong wind, the rotor blades can reach a speed exceeding 162 km⁄h. At such speed, the rotor blade tips are almost invisible, thus pre-senting an extreme injuring risk. Wind generator must under no circumstances be installed at a spot where persons could get into contact with rotor blades in movement.
• The wind generator must be installed away from the danger zone, i.e., at a minimum of 2.70 m above the ground. A safety distance of a minimum of 2.70 m must be respected during opera-tion. Caution! The spot of installation of the wind generator must must prevent persons from getting in the rotor blade zone.
• The pole and its fixings must be able to resist the wind forces generated and the pressure rais-ing. Therefore, you should consult an expert who is able to evaluate the dangers and installation.
• A wind generator at its maximum speed can generate direct voltage of more than 200 V. So only connect these devices in case you are competent and able to do so. If you disobey the safety prescriptions, these voltages might be mortal. So never touch non-insulated cable ends. Note that each non-insulated cable can cause damages.
• The cables, connecting elements, switches, and other electric components must have a cross section that prevents the cables from heating up and causing fire. Cables must be placed in a safe manner so that they cannot be damaged mechanically. A damaged cable is dangerous for your safety.
• In any case, avoid a short circuit of the battery cables and/or main cables. Make sure that the electric installation is only realised by competent persons (electrically qualified persons) that can evaluate the job to do and to be aware of the potential dangers.
• When assembling the device, make sure that all screws are well tightened. Secure the device before each storm or hurricane to avoid damages.
• The faster the wind generator, the higher the voltage. The nominal power is reached as soon as the nominal speed is reached.
• Depending on the wind force, the wind generator has a maximum power of 300 to 500 W. How-ever, this power is too low to operate large electric devices. The wind generator is rather suitable for seconding solar panels or operating small electric devices.

Technical specifications

Parts list

Installation

Installing the flange
Put the flange onto the generator spindle. Mount the generator to the device and make sure that it is straight. Put the high-quality steel plate on top, apply light pressure, and tighten the screw nuts. Connecting to the command Gently turn the rotor blades a bit after mounting of every piece. Check if all pieces are correctly mounted and tightened, and then put the device on its support. Connect cables, recharger, and batteries.

ATTENTION

• External control is not required.
• The wind generator does not need to be connected to a regulator but can be connected directly to the battery. The red wire of the wind generator is connected to the positive electrode of the battery, the blue wire is connected to the negative electrode.
• Welding the flange to the device is not necessary.

Regulations for waste disposal

The Waste Electrical and Electronic Equipment Directive (WEEE Directive, 2012/19/EU) of the EU was implemented in the German law related to electrical and electronic equipment and appliances. All WilTec electric devices that fall under the WEEE directive are labelled with the symbol of a crossed-out wheeled rubbish bin. This symbol indicates that this electric device must not be disposed of with domestic waste. WilTec Technik GmbH is registered with the German registration authority EAR (Stiftung Elektro-Altgeräte Register) under the WEEE-registration number DE45283704.
Disposal of used electrical and electronic devices (intended for use in the countries of the European Union and other European countries with a separate waste collection system for these devices). The symbol on the packaging or the product itself indicates that this product must not be treated as normal domestic waste but must be disposed of at a recycling collection station for electrical and electronic waste. By disposing of this product correctly, you contribute to the protection of the environment and the health of your fellow people. Inappropriate disposal threatens the en-vironment and health.
Material recycling helps to reduce the consumption of raw materials. Additional information about the recycling of this product can be provided by your local commune, the municipal waste disposal facilities, or the store where you purchased the product.

Important Note:
Reproduction and any commercial use (of parts) of this operating manual, requires written permission of WilTec Wildanger Technik GmbH.

References

• WilTec - Ihr Online Shop für Haus, Garten, Werkstatt, Freizeit

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>