iEBELONG ERC112 Smart Switch Controller Instruction Manual

iEBELONG ERC112 Smart Switch Controller Instruction Manual

Introduction

ERC112 smart controller can be controlled with EU1254 wireless kinetic switch, no battery is needed during use. It has WiFi module inside, so can be controlled remotely with mobile APP, and also can use voice control with Amazon Alexa.

Product parameters

• Controller Model: ERC112
• Kinetic Switch: EU1254
• Controller Voltage: AC 100V-240V 50/60Hz
• Rate power: 500W INC or 250W LED or CFL
• Wireless Communication: WiFi 2.4GHz & RE 902 MHz
• Control distance : 50m(Outdoor) 30m (Indoor)
• Sensitivity: -110dBm
• Storage Capacity: Maximum 10 switch keys can be paired
• Dimming controller dimensions: L44W41 107mm
• Kinetic switch dimensions: L33W16H65mm
• Switch base plate dimensions: L44W3H107mm

Installation

Controller

1. Use the line cap to wire as shown
   

2. Load t he controller into t he wire box and u se wallplate to cover.

   • Wallplate need tobe purchased separately

EU1254 Kinetic Switch

1. Mount t he base plate on the wire box or wall.
2. Adhere the wireless kinetic switch to t he base plate.

Pairing Method

In some cases, you need to re-pair the controller and kinetic energy switch. Methods as below.

1. Power on the dimming controller, and then keep pressing the pairing key about 6 seconds, when the indicator light flash slowly (flash 1 time per second), then release the key, and the controller is ready for pairing.You can also click the “pairing” button in the app to make device enter pairing mode.
2. At this time, press any button of the kinetic energy switch once (do not press several times). If the indicator light if off, it means that pairing is successful.
3. If need to pair with multiple switches, repeat the above procedure. Please note one controller can be paired with maximum 10 switches.
4. After paring, can press the kinetic energy switch to control dimming controller.

Common Pairing Method

1. Long press pairing key 6 seconds, indicator light will flash slowly.

2. Click any key of kinetic switch once.

Control Instructions

Dimming controller can be controlled by kinetic switch after paired:

This Controller also can be installing in multi-gang locations
like 3 GANG follow the MAX ratings below:

• LED: 250W each
• INCANDESCENT: 500W each

Clear Pairing

1. If you need to clear paring of switch and controller.You should keep press the pairing key 12 seconds until the light changes from blinking to steady light and then goes out. Or click on the “Clear Pairing” button in the app.
2. After clearing the pairing, the kinetic switch will no longer control the controller, but can be paired again.

APP download

This controller can use mobile APP for remote control. Search ” Kinetic switch” in App Store or Google Play and download, or scan below QR code to download.

Connect WiFi Method

1. Use mobile phone to download the app and follow the prompts to register your account in the app.
2. Power on the controller , and confirm the indicator light flashes qucikly (twice per second ). If the indicator light is not flashing quickly, press and hold pairing key about 10 seconds, the indicator light will flash from slowly to stay on, release pairing key when the indicator light stay on. After 3 seconds,the indicator light will flash quickly(twice per second),which means that controller is ready for WiFi connection.
3. Click the “+” button in top right corner of APP, and then select “Single receiver controller”.
4. Then click “confirm indicator light rapidly blink” and enter password of WiFi, it starts to connect. If the indicator light goes off, which means APP connect successfully and you can find the device in the home page of APP.
5. After the pairing with network, so can use APP to trun on/off light . Also,you can use mobile app for remote control, timed control and scene control.
6. If you need to replace the router, you need to delete all the devices in the app, and then re-add each device to your account once in the new router.
   

ECHO

1. In the Kinetic Switch APP, rename the controller devices, such as bedroom lights.
2. Add the SmartLife skill in Alexa APP, and log in by using the account and password of the Kinetic Switch APP.
3. Discover the device in the smart application selection in the Alexa APP.
4. Now you can control and controller with voice.

“Alexa,turn on/off bedroom light”
“Alexa, bright bedroom light”

Troubleshooting

1. WiFi connection failed
   Troubleshooting method: Please confirm the indicator light is blink rapidly (twice per second); If not blink rapidly, please set the indicator light to blink rapidly according to connect WiFi method. Let router, controller and mobile phone as close as possible (within 5 meters)

2. The controller is off line in APP
   Troubleshooting method: Maybe the number of the router connection over the maximum. Usually, only 15 devices can be connected with Common router, please upgrate router and close devices not needed.

3. Controller can not work after power on
   Troubleshooting method: If the loads exceed the rated current or short circuit, the fuse may blow. Please check the loads if suitable.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>