Shenzhen Tectronic Technology 60343073621 Wireless Charging Pad User Manual
- June 5, 2024
- Shenzhen Tectronic Technology
Table of Contents
60343073621
Wireless Charging Pad
User Manual
Thanks for choosing Mobile To Go!
This Fast Wireless Charging Pad allows you to enjoy the freedom and
convenience of wireless charging. Simply place your phone on the center of the
pad to begin charging. Please read this manual before using the device to
ensure safe and proper use.
Getting Started
Package Contents
- Wireless Charger
- Charging Cable
Wireless charging covers and chargers are sold separately.
Device Layout:
Indicator Light Identification:
Color | Status |
---|---|
Solid Amber | Standby |
Solid Green | Charging |
Using the Wireless Charger
- Connect the micro cable (included) to the charging pad and your charger adapter (not included). When the LED lights up amber it is ready for charging.
- Place your phone down on the center of the charging pad.
- When the phone is properly aligned, the LED light will change to green.
Your phone is now charging.
Notes:
- Fast charge mode is compatible with any phone that can receive 10W input.
- Standard Qi-enabled devices will charge at a standard speed, such as iPhone 8/8plus, and iPhone X.
- Phones without standard Qi function need an additional Qi wireless receiver (not included). It is normal for your phone to get warm during the charging process, removing a phone case is recommended while charging.
Specifications
Input: 5V/2A;9V/1.8A
Receiving distance: 4~10mm
Frequency: 115.6kHz – 148.2kHzSize: 100*100mm
Output:
Conversion: >72%
5W/7.5W/10W/15W
N.W.: 81g
Can cause damage to the device
Can cause bodily hard to user or another person.
Do not squeeze or collide with other items.
Do not disassemble or throw into fire or water, to avoid causing a short
circuit leakage.
Do not use the wireless chargers in severely hot, wet, or corrosive
environments, to avoid circuit damage and leakage phenomenon.
Do not place close to a magnetic stripe or chip card (ID card, bank
cards, etc.) to avoid magnetic failure.
Please keep an 8-inch distance between embedding medical devices
(pacemakers, embedding cochlear, etc.) and the wireless charger, to avoid
potential interference with the medical device.
Do not block the charging fan on the bottom of the wireless charger.
Do not place materials such as metals, magnets, or magnetic stripes
between the mobile device and the wireless charger.
Please advise children this charger is not a toy.
FCC Statement
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment. This
equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions (1)this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>