FORCE1 F1 Stunt Riders Mini Flaying Action Figures User Manual

FORCE1 F1 Stunt Riders Mini Flaying Action Figures

PARAGLIDER CONFIGURATION

ASSEMBLY

1. Insert Left and Right Wings into the body of the drone.
2. Align the Drone Tail to the Drone Body Connector; then rotate the Drone Tail 90° and snap it into the Socket.
3. Attach Stunt Rider to the bar.
4. Attach the bar to the drone.

HOVERBOARDCONRGURATION

ASSEMBLY

1. Snap the Stunt Rider into the Drone Body Foot Clips.
2. Insert the Bumpers into the Drone Body.
3. Insert Handlebar into Front Bumper and attach the Stunt Rider’s hands to the handlebar

transmitter

BUTTON FUNCTIONS

__

Power Switch

| Press Power Switch ta turn an the Transmitter. Hald the button ta turn it off.
Stunt Made| Press the Stunt Button ta perform Around-the-Black Stunt!
__

1-Key Lift/Land/ Emergency Stop

| __

After pairing, press the button ta launch the drone. Press the button again ta land the drone. Press and hold the button and the drone propellers will immediately shut off.

__

Headless Mode

| __

Headless Mode orients the drone ta the Transmitter’s directional position. To set the direction, ensure the drone is facing away from you and press the Headless Mode button. Forward will now be forward no matter what orientation you are facing. Press the button again ta exit Headless Made.

__

3 Speed Modes

| Press the Speed Button ta switch between Low, Medium and High Speeds.
Drane Configuration| Press the Paraglider/Hoverboard Made Button left far Haverbaard Mode, and right for Paraglider Made.

FLYING

PAIRING

First, turn on the drone, and the red light will blink. Ensure the Transmitter is in the correct configuration made [Haverbaard or Paraglider], then press the power button ta turn the Transmitter, and the red light will blink. Shift the Left Stick downward once (as seen in the diagram below). The Transmitter will beep twice and the red lights will tum solid, indicating a successful pairing.

BEFORE TAKEOFF

Hoverboard Mode

When using Hoverboard Mode, place the drone on a level surface before takeoff.

Paraglider Mode When using Paraglider Mode, place the Stunt Rider face down on a level surface, with the drone in an upright position before takeoff.

TRIM

BATTERY INSTALLATION

Open the battery cover on the back side of the Transmitter and install 3 AAA batteries {not included) with the + and – ends facing as shown. Close the battery cover after installing.

Important Notice: Please do not mix different kinds of batteries. Do not mix old and new batteries. Do not charge non-rechargeable batteries.

ADDITIONAL FUNCTIONS

LOCK/ UNLOCK MOTORS

Shift the Left and Right Sticks downward and inward at the same time at mirrored 45° angles to unlock the motors: perform the same operation to lack the motors.

LOW BATTERY ALARM

When the Transmitter battery is law, the Transmitter will continuously beep, Letting you know it’s time to recharge the drone.

UNLOCK PROPELLERS

If the propellers become locked, unlock them by shifting the Left Stick down and then back to the center position; the propellers will re-engage.

ALTITUDE HOLD

Altitude Hold is an intelligent flight control system that automatically maintains altitude.

PROPELLER REPLACEMENT

To remove a propeller, hold the motor in place while pulling the propeller out vertically.
To install a propeller, align it with the central shaft of the motors and press down (Picture 1).
Note: The propellers and motors are marked A and B (See diagrams below). Be sure to match the correct propellers with the correct motors, otherwise, the drone will not function properly.

CHARGING

1. With the drone-powered off, attach your USB cable to the drone, then connect it to your preferred charging source.
2. The drone’s charging indicator will turn red while charging, and green when fully charged.
3. The charge time is approximately 50 minutes.

WARNING:
DO NOT LEAVE BATTERY CHARGING UNSUPERVISED

Li-Pa Battery Disposal & Recycling 

Wasted Lithium-Polymer batteries must not be placed with household trash. Please contact the nearest Li-Pa battery recycling center.

FCC NOTES

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FCC Notice:

The equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. Modifications not authorized by the manufacturer may void user’s authority to operate this device.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

FCC Radiation Exposure Statement
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

To ensure that play is both safe and fun, please review these operating instructions:
Failure to follow all safety instructions may result in injury or property damage none of which Force1 will be held liable for as proper warnings are outlined in the manual.

• Upon use of this product, the end-user assumes all responsibility, and Force1 cannot be held liable for any personal injury and/or property damage.

• This item contains fast-moving parts, motors, and/or other wiring. When using it, basic precautions should always be followed including but not limited to
  the following:

  • Keep your eye on the product at all times
  • Tie back hair or wear a hat to avoid entanglement or injury
  • Keep hands, hair, and loose clothing away from moving parts when the power switch is turned ON.
  • Please ensure the product is turned off when not in use.

WARNING: CHANGES OR MODIFICATIONS TO THIS UNIT NOT EXPRESSLY APPROVED BY THE SELLER WILL VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>