Aprilla AHC 5007 Hair Trimmer Instruction Manual
- June 5, 2024
- Aprilla
Table of Contents
Aprilla AHC 5007 Hair Trimmer
SAFETY INSTRUCTIONS
IMPORTANT: OIL THE BLADES BEFORE THE FIRST USE, AND KEEP OILING THEM AFTER EVERY USE!
-
By ignoring the safety instructions the manufacturer can not be hold responsible for the damage.
-
Do not use this appliance with a damaged cord or plug or when the appliance has malfunctions, or has been damaged in any manner. To avoid a hazard make sure that a damaged cord or plug will be replaced by an Competent qualified repair service(*). Do not repair this appliance yourself.
-
Never move the appliance by pulling the cord and make sure the cord can not become entangled.
-
The appliance must be placed on a stable, level surface.
-
The user must not leave the device unattended while it is connected to the supply.
-
This appliance is only to be used for household purposes and only for the purpose it is made for.
-
To protect children against the dangers of electrical appliances, please make sure that you never leave the appliance unattended. Therefore you have to select a storage place for the appliance where children are not able to grab it. Make sure that the cable is not hanging in a downward position.
-
To protect yourself against an electric shock, do not immerse the cord, plug or appliance in the water or any other liquid.
-
This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.
-
WARNING: Keep the appliance dry.
The parts that have to be fixed must be installed so they cannot fall into water. -
Competent qualified repair service: after sales department of the producer or importer or any person who is qualified, approved and competent to perform this kind of repairs in order to avoid all danger. In any case you should return the appliance to this repair service.
PARTS DESCRIPTION
- Blades
- Combs 1 to 4
- On/off switch
- Blade lever
BEFORE THE FIRST USE
- Check the clippers, making sure that they are free of hair and lint. Clean it with the supplied cleaning brush and spread a drop of oil on the blades.
- Use the device only on dry hair.
USE
-
The following table provides which comb you need to cut the desired lengths.
-
To put the comb down, hold the comb with teeth up and push the comb firmly against the blade side.
Comb 1 leaves hair approx. 0.3 cm. in length.
Comb 2 leaves hair approx. 0.6 cm. in length.
Comb 3 leaves hair approx. 0.9 cm. in length.
Comb 4 leaves hair approx. 1.2 cm. in length. -
At the beginning, cut only a small amount of hair until you become accustomed to the length. Each comb leaves the hair. It is suggested to try the longest comb 4 on the clipper first, then use a another comb if the desired length is shorter. For uniform cutting, never push or force the clipper through the hair at a fast rate
-
Start by combing the hair in its natural direction, place the largest, attachment comb onto the clipper and start by trimming the sides from the bottom upwards. Hold the clipper lightly against the hair with teeth of the attachment comb pointing up.
Slowly lift the clipper up and outward through the hair, cutting only a small amount at a time. Repeat around sides and back of head.
Use blade lever
-
The allows you to gradually change the closeness of your cut without an attachment comb. When the lever is in the uppermost position, the blades will give you the closest cut and leave the hair very short. Pushing the lever downward gradually increases the cutting length.In its lowest position, the lever will leave the hair approximately the same
-
Always remove the plug from the outlet first. After each use, remove any hair with the cleaning brush and spread one or two drops of oil on the blades. Use only acid-free oil as supplied. Unscrew the blades regularly and remove all hair trimmings. When replacing the blades make sure that they are properly adjusted. The blades are adjusted as follows:
-
Screw the blades back on the clippers, but do not turn the screws tightly yet.
-
Turn the blade lever to the side downward.
Shift the top blade until it is even (parallel) with the bottom blade and be sure that the two blades are about 1.2mm (1/32 inch) apart. -
Now tighten screws firmly and make sure that the blades cannot shift.
-
Clean the outside of the clipper with a clean soft, damp cloth. Never immerce the device in water or other liquid.Do not place or store appliance where it can fall or be pulled into a tub or sink.
CLEANING AND MAINTENANCE
- Brush the blades using the cleaning brush to remove any hair.
- After each use it’s recommended to oil the trimmer blades with the supplied oil.
GUIDELINES FOR PROTECTION OF THE ENVIRONMENT
This appliance should not be put into the domestic garbage at the end of its
durability, but must be offered at a central point for the recycling of
electric and electronic domestic appliances. This symbol on the appliance,
instruction manual and packaging puts your attention to this important issue.
The materials used in this appliance can be recycled. By recycling of used
domestic appliances you contribute an important push to the protection of our
environment. Ask your local authorities for information regarding the point of
recollection.
Exporter-Manufacturer
BMVA Elektronik San. Tic. ve A.Ş. Osmangazi Mh, 2644. Sk. No:3/2 Kıraç-
Esenyurt / Istanbul – TURKEY export@bmva.com.tr
K1951/11.20 – Made in China
This device appropriate for regulations according to Waste Electrical and Electronic Equipment (WEEE).
© 2020 BMVA. All rights reserved. Aprilla logo is owned by BMVA and registered. All other trademarks and signs are property of their owners. BMVA is not responsible for printing and composing mistakes.