Brookstone BKWIFICAM Wi-Fi Camera User Manual
- June 5, 2024
- Brookstone
Table of Contents
__
Brookstone BKWIFICAM Wi-Fi Camera
FCC Statement:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Caution: The user is cautioned that changes or modifications not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more
of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator and any part of your body.
For more products please visit www.brookstone.com
SPECIFICATIONS
- Model: BKWIFICAM
- Resolution: 1280×720
- Alarm: Motion detection
- Night Vision: 8-10m
- Sensor: 1.0 Megapixel 1/4 CMOS
- Audio: Microphone & Speaker built-in TF Card
- Storage: Up to 128GB
- Compression: H.264
- Power: 5V/1A (DC)
- Operating System:
- Android 8.0 or higher, iOS 7.0 or higher
WARRANTY INFORMATION
One Year Limited Warranty.
Customer Service: 732-994-2301; email:
help@smartpointco.com
The BROOKSTONE trademark. names and logos are owned by
BKST Brand Holdings LLC ©2020. All rights reserved
Manufactured, marketed and distributed by Smartpoint LLC, under license Alexa®
is a registered trademark of Amazon, Inc
Android and Google Play are trademarks of Google LLC.
App Store® is a registered trademark of Apple, Inc
All trademarks and Registered trademarks are property of their respective
owners Made in China
©Smartpoint LLC,
250 Liberty Street Metuchen NJ, Suite 1A
FEATURES
- Wi-Fi remote controlled through App
- Remotely control tilt and pan movement of lens for 360° of coverage
- Night vision
- Motion detection
- Two way audio
- Live video
- Video recording
- Takes still photos
PRODUCT CONFIGURATION
Items included in package:
Camera, Adapter, USB Cable and User Manual.
DOWNLOAD APP
- Android: download “Brookstone Smart” app on Google Play.
- iPhone: download “Brookstone Smart” app from the App Store.
REGISTRATION AND LOGIN
- Run the “Brookstone Smart” app from your smart phone.
Register and login.
*Screenshots may slightly differ from actual app.
ADD DEVICE
-
Plug-in Wi-Fi Camera into the wall. After about 30 seconds camera will move around. After another 15 seconds it will make a chiming sound. Camera is now ready to be set up.
-
Make sure phone is connected to your Wi-Fi network and that it is a 2.4GHz network.
-
Press the (+) symbol in the top right corner of the app and select the Smart Camera from the list of devices to add.
-
. Press the “next step” button
-
Make sure phone is connected to the Wi-Fi network that the device will be connected to. Enter your password for the Wi-Fi network.
-
Follow the directions in the app and hold the QR code on the screen in front of the view of the camera.
-
Connecting process will begin. Do not turn off Wi-Fi Camera or phone while connecting. Wait for connection process to complete.
-
Once device has been successfully added, name the device what you would like it to be called in the app. The Wi-Fi Camera is ready for use.m
PUSH NOTIFICATIONS
- You can turn on/off notifications for all devices connected to app by clicking on the “Me” button at the bottom right of the screen.
- Then click on ”Settings” button. From there you can turn on/off all notifications.
**REMOVE A DEVICE
**
- From the home screen, click on the device you would like to remove.
- Then click on the edit symbol on the top right of the screen.
- From there you would then click the “Remove Device” button at the bottom of the screen.
APP FUNCTIONS
Live Video
To view live video simply click on the device under “All devices” and you will
see your live video at the top immediately. Tilt your phone sideways or hit
the full screen button in the bottom right corner of the live video to see
your live footage at full screen on your phone.
Video Recording
To record video press the “record” button one the main camera screen. To end
recording, press “record” button again. To view recordings, scroll down on the
main camera page and press the “Photo Album” button. All of the video
recordings and photos you take will be here in the photo album. To view all
footage that your camera has recorded, press “Playback”. You can also purcahse
optional cloud storage by clicking on “Cloud Storage” if you do not have a
miro SD card inserted in your camera.
Taking a Photo
To take a photo, press “take a photo” and the photo will be saved to your
phone in the photos and video section.
Infrared Night Vision
Infrared night vision is controlled by camera automatically. When the area
around the camera becomes too dark, the infrared night vision will activate
automatically. When the area around the camera is bright again, the night
vision will deactivate automatically.
Two Way Audio
To activate two way audio, press the “speak” button. When the button is blue,
whatever you say into your phone will come out of the speaker on the camera.
You can also hear at the same time any sounds from the live video on the
camera.
Motion Detection
The camera uses infrared sensors when someone/something appears within its
detection area. Push notifications will be sent your phone once motion is
detected.
To access control of motion detection press the camera setting button at the
top right. On the next page you can select “motion detection”. From there you
can turn it on/off and set the sensitivity setting. You can also get to this
from scrolling downand pressing the “alarm” button on the main camera page.
Remotely Controlling the Camera Lens
To remotely control the camera press the “Direction” button on the main camera
screen. From here you can rotate pan or tilt on the camera lens. You can also
control the pan and tilt movement of the lens by turning your phone sideways
and dragging your finger in any direction on the screen.
Hub controls (sound, video quality, signal strength)
You can control features from the live video feed. There is a volume button
that is used to mute and unmute the live feed. Next to that button is the
video quality button and it can be used to switch between standard and high
definition video. In the top right, the signal strength of the camera is shown.
Sharing the Device
To share access to your camera with someone else’s Brookstone Smart account,
press the camera options button at the top right of the main camera screen.
Then hit “Share Device”. On the next page press “Add Sharing” at the bottom.
After that, enter the email on the person’s Brookstone Smart account that you
would like to share the camera with. They will get a notification to accept and
after that the other person will have access to view your camera through the
Brookstone Smart app on their phone.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>