Brookstone BKWIFICAM2 Smart Camera User Manual
- June 5, 2024
- Brookstone
Table of Contents
Smart Camera
USER MANUAL
FCC ID: 2AT5D-ZS-GX1
FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
To maintain compliance with FCC’s RF exposure guidelines, This equipment
should be installed and operated with a minimum distance of 20cm from the
radiator of your body: Use only the supplied antenna.
For more products please visit www.brookstone.com
SPECIFICATIONS
Model: BKWIFICAM2
Resolution: 1280×720
Alarm: Motion detection
Night Vision: 8-10m
Sensor: 1.0 Megapixel 1/4 CMOS
Audio: Microphone & Speaker built-in
Micro SD Card Storage: Up to 128GB
Compression: H.264
Power: 5V/1A (DC)
Operating System:
Android 8.0 or higher, iOS 7.0 or higher
WARRANTY INFORMATION
One Year Limited Warranty.
Customer Service: 732-994-2301; email:
help@smartpointco.com
The BROOKSTONE trademark. names and logos are owned by BKST Brand Holdings LLC
©2019. All rights reserved Manufactured, marketed, and distributed by
Smartpoint LLC, under license Google and Google Play are trademarks of Google
LLC. App Store ® is a registered trademark of Apple, Inc All trademarks and
Registered trademarks are property of their respective owners. Made in China
©Smartpoint LLC,
250 Liberty Street, Suite 1A
Metuchen, NJ 08840
FEATURES
- Wi-Fi remote controlled through App
- Remotely control tilt and pan movement of lens for 360° of coverage
- Night vision
- Motion detection
- Two-way audio
- Live video
- Video recording
- Takes still photos
PRODUCT CONFIGURATION
Items included in the package : Camera, Adapter, USB Cable, Mounting Kit, and User Manual.
DOWNLOAD APP
- Android: download the “Brookstone Smart” app on GooglePlay.
- iPhone: download the “Brookstone Smart” app from the App Store.
Brookstone Smart
|
---|---
https://itunes.apple.com/cn/app/brookstone
-smart/id1456388657?l=en&mt=8| https://play.google.com/store/apps/details?id=com.brookstone.smart
|
REGISTRATION AND LOGIN
- Run the “Brookstone Smart” app from your smartphone.
- Register and log in.
ADD DEVICE
- Plug-in Wi-Fi Camera into the wall. After about 20 seconds it will make a chiming sound and then the red light will start blinking rapidly. The camera is now ready to be set up.
- Make sure your phone is connected to your Wi-Fi network and that it is a 2.4GHz network.
- Press the (+) symbol in the top right corner of the app and select the Smart Camera from the list of devices to add
- Press the “next step” button
- Make sure the phone is connected to the Wi-Fi network that the device will be connected to. Enter your password for the Wi-Fi network.
- Follow the directions in the app and hold the QR code on the screen in front of the view of the camera.
- The connecting process will begin and the status light will turn blue. Do not turn off the Smart Camera or phone while connecting. Wait for the connection process to complete.
- Once the device has been successfully added, name the device that you would like it to be called in the app. The Smart Camera is ready for use.
PUSH NOTIFICATIONS
- You can turn on/off notifications for all devices connected to the app by clicking on the “Me” button at the bottom right of the screen.
- Then click on the” Settings” button. From there you can turn on/off all notifications.
REMOVE A DEVICE
- From the home screen, click on the device you would like to remove.
- Then click on the edit symbol on the top right of the screen.
- From there you would then click the “Remove Device” button at the bottom of the screen.
APP FUNCTIONS
Live Video
To view the live video simply click on the device under “All devices” and you
will see your live video at the top immediately. Tilt your phone sideways or
hit the full screen button in the bottom right corner of the live video to
see your live footage at full screen on your phone.
Video Recording
To record video press the “record” button on the main camera screen. To end
the recording, press the “record” button again. To view recordings, scroll
down on the main camera page and press the “Photo Album” button. All of the
video recordings and photos you take will be here in the photo album. To view
all footage that your camera has recorded, press “Playback”. You can also
purchase optional cloud storage by clicking on “Cloud Storage” if you do not
have a micro SD card inserted in your camera.
Taking a Photo
To take a photo, press “Screenshot” and the photo will be saved to your phone
in the photos and video section.
Infrared Night Vision
Infrared night vision is controlled by the camera automatically.
When the area around the camera becomes too dark, the infrared night vision
will activate automatically. When the area around the camera is bright again,
the night vision will deactivate automatically.
Two Way Audio
To activate two way audio, press the “Speak” button. When the button is blue,
whatever you say into your phone will come out of the speaker on the camera.
You can also hear at the same time any sounds from the live video on the
camera.
Motion Detection
The camera uses infrared sensors when someone/something appears within its
detection area. Push notifications will be sent to your phone once the motion
is detected.
To access control of motion detection press the camera setting button at the
top right. On the next page, you can select “Motion detection”. From there you
can turn it on/off and set the sensitivity setting. You can also get to this
by hitting the “alarm” button on the main camera page.
Remotely Controlling the Camera Lens
To remotely control the camera press the “Direction” button on the main camera
screen. From here you can rotate the pan or tilt the camera lens. You can also
control the pan and tilt movement of the lens by turning your phone sideways
and dragging your finger in any direction on the screen.
Hub controls (sound, video quality, signal strength)
You can control features from the live video feed. There is a volume button
that is used to mute and unmute the live feed. Next to that button is the
video quality button and it can be used to switch between standard and high
definition video. In the top right, the signal strength of the camera is
shown.
Sharing the Device
To share access to your camera with someone else’s Brookstone Smart
account, press the camera options button at the top right of the main camera
screen. Then hit “Share Device”. On the next page press “Add Sharing” at the
bottom. After that, enter the email on the person’s Brookstone Smart account
that you would like to share the camera. They will get a notification to accept
and after that, the other person will have access to view your camera through
the Brookstone Smart app on their phone.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>