IPCAMPOWER IPCP-WIPOERECIEVER POE to 12V DC Adapter with Wireless Receiver User Manual

IPCP-WIPOERECIEVER POE to 12V DC Adapter with Wireless Receiver
User Manual

Connection and Setup:

1. Connect the PoE adapter with an Ethernet cable to a PoE Switch or Injector.
   Ensure that your POE power pushes at least 17 watts in order to achieve the maximum 12V DC output of 1.2 amps

2. Connect your 12V DC device to the Green DC Phoenix Terminals on the PoE adapter using correct polarity. Ensure that your 12V DC powered the device does not consume  more than 1.2 amps

Connection Diagram:

Specifications:

• Input Power PoE Standards, IEEE 802.3at (needs at least 17 watts for maximum power)
• Output Voltage: 12VDC
• Output Current: 1.2A
• Ports: 1 x RJ45 Ethernet POE Input 1 x 12VDC Green Phoenix Terminals
• Pin Assignment: Power (1/2+ & 3/6-)
• Dimensions: 108(L) x 38(W) x 30(H)mm
• Receiving frequency: 433.92Mhz
• Receive sensitivity: 110dBnn
• Decoding format: learning code 1527
• Program up to 31 individual IPCP-REMOTE SWITCH to 1 IPCP-WIPOERECEIVER
• 3 Different Programming Mode Options (Light Switch Mode, Constant Push Mode, Double Remote Mode)
• Working temperature: -20-80°C

Programming Instructions

*** Please note that this requires the use of an IPCamPower IPCP­ REMOTE SWITCH to operate and program.

You will need a pin or a tiny screwdriver to access and push the learning key button on the WIPOERECEIVER. This is within the tiny hole labeled “Key” on the unit. When pushing the learning button, you will see a led light within the case flash indicating that the button has been pushed.

Light Switch Mode:
This mode works like a typical light switch. When you push the REMOTE SWITCH, the current flows through to the device and stays flowing and constant until you push the  REMOTE SWITCH again which is when the current would stop.

• Quickly presses the learning button twice, and you will then see the internal learning light remain constant.

• Within 10 seconds, push the REMOTE SWITCH.
  You will then see the internal learning light flash 3 times

• Your REMOTE SWITCH is now learned in

Constant Push Mode:
This mode only allows current to flow through the adapter as long as the REMOTE SWITCH is pressed and held down. As soon as the REMOTE SWITCH is released, the current flow stops.

• Press the learning button once, you will then see the internal learning light remain constant.
• Within 10 seconds, push the REMOTE SWITCH.
• You will then see the internal learning light flash 3 times
• Your REMOTE SWITCH is now learned in

Double Remote Mode:
This mode requires the use of 2 REMOTE SWITCH units. Once you push REMOTES WITCH #1, the current flows and remains constant, and the current will not stop until  REMOTES WITCH #2 is pushed.

• Quickly press the learning button 3 times. you will then see the internal learning light remain constant.
• Within 10 seconds, push the REMOTE SWITCH.
• You will then see the internal learning light flash 3 times
• Your REMOTE SWITCH is now learned in

*** To clear any programming from the WIPOERECEIVER:
Quickly push the learning button 8 times. You will then see the learning led light flash rapidly.

FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the  user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by the manufacturer could void your authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RF Exposure Information
The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>